Analysis of the Facial Measurements and Dental Arch Dimensions for the Construction of Dental Prostheses among Adult Yemenis.

AIM: To investigate the dental arch dimension (width, length, and height) and facial measurements including inner-canthal width (ICW), bizygomatic width (BZW), inter-alar width (IAW), and mouth width (MW), and to assess the correlation between these facial measurements and dental arch width (canine width [CW], inter-first premolar width [I1PW], and inter-first molar width [I1MW]), to establish a preliminary reference for artificial teeth selection in Yemeni adult. MATERIALS AND METHODS: The study included 80 individuals (40 males and 40 females) with symmetrical faces and normal class I occlusion ranging in age from 20 to 35. Maxillary and mandibular stone casts were made for each individual. The dimensions of dental casts and facial measurements, including ICW, BZW, IAW, and MW, were assessed using a digital caliper. The collected data were analyzed by using the SPSS software program. The descriptive statistics for each measurement were made. Differences between males and females were tested using an independent-sample t-test with p-values below 0.05 considered significant. Pearson correlation coefficient between facial measurements and dental arch width was also done. RESULTS: Most dental arch dimensions and facial measurements exhibited larger mean values in the male than in the female group, with the greatest significant difference in the maxillary dental arch width and the lowest in mandibular dental arch length. A highly significant correlation is observed between ICW and maxillary canine width (CW) (r = 0.318, p = 0.004). In contrast, no significant correlation between dental arch width and BZW, IAW, and MW is shown. CONCLUSIONS: Within this study's limitations, the ICW can determine the ideal dimension of the artificial teeth in the anterior maxillary arch. While the other facial parameters, including BZW, IAW, and MW, cannot be used for artificial teeth selection in Yemeni populations. CLINICAL SIGNIFICANCE: The findings of this study established a reference database of facial measurements and their correlation to dental arch and teeth width in Yemeni populations. So, it can be implemented in artificial teeth and dental prostheses design and construction.

Hyaluronic Acid: A New Approach for the Treatment of Gingival Recession-A Systematic Review.

This systematic review aimed to investigate the effectiveness of hyaluronic acid (HA) on the clinical treatment outcomes of patients with gingival recession. A systematic search was performed in PubMed, Cochrane Central Register of Controlled Trials, Embase, Scopus, and Google Scholar for studies up to 15 August 2022. Two reviewers separately selected the papers for eligibility after conducting a thorough search. The study includes randomized controlled clinical trials in which participants were given HA in addition to periodontal treatment surgical procedures. The changes following the treatment protocol were evaluated for complete and mean root coverage as a primary outcome and gingival recession gain as the secondary outcome. Three articles met the eligibility criteria out of 557 titles. In periodontal surgery, HA exhibited better results in complete root coverage and mean root coverage when compared to the control group. Gingival recession reduction, clinical attachment level, and keratinized tissue gain were significantly increased compared to the control groups. However, the comparison presented in the following study might show heterogeneity among the studies and risk of bias in general. Given the scope of this analysis, results suggest that adjunctive treatment with HA gel for root coverage could be clinically beneficial.

Assessment of Conventionally and Digitally Fabricated Complete Dentures: A Comprehensive Review.

CAD/CAM technology is gaining popularity and replacing archaic conventional procedures for fabricating dentures. CAD/CAM supports using a digital workflow reduce the number of visits, chair time, and laboratory time, making it attractive to patients. This study aimed to provide a comparative review of complete dentures manufactured using CAD/CAM and conventional methods. The PubMed/Medline, Science Direct, Cochrane, and Google Scholar databases were searched for studies published in English within the last 11 years (from 2011 to 2021). The keywords used were "computer-engineered complete dentures", "CAD/CAM complete dentures", "computer-aided engineering complete dentures", and "digital complete dentures". The search yielded 102 articles. Eighteen relevant articles were included in this review. Overall, computer-engineered complete dentures have several advantages over conventional dentures. Patients reported greater satisfaction with computer-engineered complete dentures (CECDs) due to better fit, reduced chair time, shorter appointments, and fewer post-insertion visits. CAD/CAM allows for precision and reproducibility with fewer procedures compared to conventional dentures. Polymethyl methacrylate is used as the denture base material for conventional dentures. For CECDs, the resin can be modified and cross-linked to improve its mechanical properties. The advantages of CECDs include a reduced number of appointments, saving chairside time, a digital workflow allowing easy reproducibility and greater patient satisfaction with a better fit.

Effects of the Cervical Marginal Relocation Technique on the Marginal Adaptation of Lithium Disilicate CAD/CAM Ceramic Crowns on Premolars.

AIM AND OBJECTIVE: To evaluate the effect of cervical margin relocation (CMR) for crowns designed using CAD/CAM technology and fabricated from lithium disilicate (e.max, CAD) before and after aging; and to compare the fracture forces and failure type of the tested crowns. MATERIALS AND METHODS: Mesio-occluso-distal(MOD) cavities 1 mm above the cementoenamel junction(CEJ) were prepared on 40 maxillary first premolars. The teeth were divided into four groups. In group A, all cervical margins (CM) were located 1 mm above the CEJ. However, in both mesial and distal proximal boxes of groups B, C, and D, in addition to the MOD cavities, the CMs were extended 2 mm on both sides below the CEJ apically to simulate the CMR technique. In group B, the mesial and distal proximal boxes were filled with flowable composite, while for group C and group D, specimens were filled with composite resin fillings. To simulate the CMR technique, the cavities were filled with composite layers of 3 mm in two increments. Using the CAD/CAM system, 40 standard crowns were prepared on premolars, then cemented using a dual-curing adhesive cement. Assessments of the marginal integrity of interfaces of the proximal boxes of the cemented crowned teeth were recorded. Statistical differences between groups were analyzed using the ANOVA and Bonferroni's posthoc test. RESULTS: The first null hypothesis was accepted since no statistically significant differences were found in marginal integrity before and after aging (p>0.05), while the second was partially rejected since different fractured force values were recorded and a significant difference was detected between group D and group B. The third hypothesis was rejected because the catastrophic fracture rate was the highest among the four groups. CONCLUSION: The implementation of CMR before and after aging had a good effect on the marginal integrity of CM relocation. The CMR technique with resin luting cement of lithium disilicate crowns is effective and recommended for the restoration in deep proximal boxes of premolars or posterior teeth. CLINICAL SIGNIFICANCE: CAD/CAM-generated e. max all-ceramic crowns with composite as the CMR enable the reconstruction of severely destroyed teeth irrespective of the position of the cavity margins.

Effects of Khat on Surface Roughness and Color of Feldspathic and Zirconia Porcelain Materials under Simulated Oral Cavity Conditions.

Background and Objectives: Khat chewing is considered as a daily habit that is practiced by more than five million people globally. The effect of khat chewing on the surface roughness and the color stability of natural teeth and the material used in the fabrication of dental prosthesis remains unknown. This study was conducted to explore and compare the effect of khat homogenate (KH) on the surface roughness (Ra) and the average color changes (ΔE*) amongst natural teeth and selected shades from different porcelain types, namely, feldspathic metal ceramic (MC) VM13, computer-aided design/computer assisted manufacture (CAD/CAM) feldspathic (Vitablocs Mark II), and multilayer zirconia (Ceramill Zolid PS) porcelains. Materials and Methods: Seventy samples were prepared from natural teeth, feldspathic MC, CAD/CAM Vitablocs Mark II, and zirconia porcelain. The Ra values were measured using a profilometer and expressed in micrometers, whereas the ΔE* values were measured using VITA Easyshade® V spectrophotometer for all samples before and after frequent immersion and thermocycling in KH for 30 days. The surface topography was used to assess the materials surfaces (glazed or polished) after KH immersion by using a white light interferometry machine. Results: Results revealed that the Ra and the ΔE* values of the different types of tested porcelain were influenced by KH. The order of surface roughness values was glazed or polished MC > polished Zircon > polished Vitablocs Mark II > natural teeth. The lowest ΔE* values were recorded for glazed Vitablocs Mark II and MC, and the values could be arranged as polished zircon > natural teeth > glazed zircon > polished MC > polished Vitablocs Mark II. P values were significantly varied (< 0.001) among all the tested groups, except the zircon group (>0.05) for both Ra and ΔE*. Conclusion: KH significantly affected both surface parameter and color of glazed or polished porcelain materials and natural teeth.

Social Habits and Other Risk Factors that Cause Tooth Loss: An Associative Study Conducted in Taiz Governorate, Yemen.

AIMS: To investigate the relationship between tooth loss, age, gender, and its correlation with several local habits that affect oral health, especially the khat, and Shammah use. MATERIALS AND METHODS: The current study included 580 participants. They were divided into five age groups15-24, 25-34, 35-44, 45-54, and 55-64-years-old. Clinical and radiographic examinations were done for each subject. Reasons for teeth loss, age, gender, khat chewing, Shammah use, smoking, and use of oral hygiene aids were recorded. The data were statically analyzed using Chi-square tests of the statistical package for social sciences (SPSS) program. The p value < 0.05 were considered statistically significant. RESULTS: Caries was the most cause of tooth loss in the young age groups 15-34 years-old and was significantly more common compared to the older groups (p < 0.001). The periodontal diseases increased with age and progressively became the main cause of tooth loss of 100% in the 55-64 years-old group. Orthodontic reasons for tooth extractions were limited to the young age group 15-24 years old. Third molars were the highest extracted teeth in the maxillary arch, while the first molars were the highest in the mandibular arch. Anterior teeth were the lowest extracted teeth ranging from 9; 1.6% in maxillary teeth and 9-29; 1.6-5% in the mandibular teeth. CONCLUSION: This study highlights the importance of local habitual use of khat 52.9% and Shammah 8.1% besides smoking in tooth loss. Caries was the main cause of tooth loss in the young age groups, followed by the periodontal disease in the older age. Molars were frequently extracted followed by maxillary first premolars. CLINICAL SIGNIFICANCE: Limited number of epidemiological surveys were carried out in Taiz Governorate to investigate the reasons of tooth loss and its relationship with social habits like Khat chewing, Shammah use, smoking, using of Miswake and toothbrush. The results of this study will guide us to develop a preventive program which may minimize tooth loss and its adverse effects.