Development and validation of a solid phase extraction sample cleanup procedure for the recovery of trace levels of nitro-organic explosives in soil.

An improved cleanup method has been developed for the recovery of trace levels of 12 nitro-organic explosives in soil, which is important not only for the forensic community, but also has environmental implications. A wide variety of explosives or explosive-related compounds were evaluated, including nitramines, nitrate esters, nitroaromatics, and a nitroalkane. Fortified soil samples were extracted with acetone, processed via solid phase extraction (SPE), and then analyzed by gas chromatography with electron capture detection. The following three SPE sorbents in cartridge format were compared: Empore™ SDB-XC, Oasis® HLB, and Bond Elut NEXUS cartridges. The NEXUS cartridges provided the best overall recoveries for the 12 explosives in potting soil (average 48%) and the fastest processing times (<30min). It also rejected matrix components from spent motor oil on potting soil. The SPE method was validated by assessing limit of detection (LOD), processed sample stability, and interferences. All 12 compounds were detectable at 0.02µg explosive/gram of soil or lower in the three matrices tested (potting soil, sand, and loam) over three days. Seven explosives were stable up to seven days at 2µg/g and three were stable at 0.2µg/g, both in processed loam, which was the most challenging matrix. In the interference study, five interferences above the determined LOD for soil were detected in matrices collected across the United States and in purchased all-purpose sand, potting soil, and loam. This represented a 3.2% false positive rate for the 13 matrices processed by the screening method for interferences. The reported SPE cleanup method provides a fast and simple extraction process for separating organic explosives from matrix components, facilitating sample throughput and reducing instrument maintenance. In addition, a comparison study of the validated SPE method versus conventional syringe filtration was completed and highlighted the benefits of sample cleanup for removing matrix interferences, while also providing lower supply cost, order of magnitude lower LODs for most explosives, higher percent recoveries for complex matrices, and fewer instrument maintenance issues.

Post-Blast Analysis of Hexamethylene Triperoxide Diamine using Liquid Chromatography-Atmospheric Pressure Chemical Ionization-Mass Spectrometry.

A qualitative method using liquid chromatography-atmospheric pressure chemical ionization-mass spectrometry (LC/APCI-MS) has been developed and validated for the identification of trace hexamethylene triperoxide diamine (HMTD) using three structurally-specific ions. Residues are extracted with deionized water (DI) and identified using a gradient mobile phase program and positive ion full scan mode on a Thermo Finnigan LCQ Ion Trap Mass Spectrometer. This method was validated according to several performance characteristics for the qualitative identification of an analyte using the characteristic ions, demonstrating the method's reliability for use on forensic applications. The method's limit of detection (LOD) can identify HMTD in an extract from a cotton matrix to which 20 µg of HMTD has been applied (equivalent to 10 ppm in extract). Previous scientific publications using LC/MS have not demonstrated post-blast HMTD residue analyses and suffer from a lack of chromatographic retention, sufficient number of mass spectral ions with validation, or require more complex/expensive instrumental methods (accurate mass or MS/MS). Post-blast analyses were successfully conducted with two syringe detonations that verified the efficacy of the method on the analysis of debris and residues following detonation.

Forensic utility of isotope ratio analysis of the explosive urea nitrate and its precursors.

Urea nitrate (UN) is an improvised explosive made from readily available materials. The carbon and nitrogen isotope composition of UN and its component ions, urea and nitrate, could aid in a forensic investigation. A method was developed to separate UN into its component ions for δ(15)N measurements by dissolving the sample with KOH, drying the sample, followed by removal of the urea by dissolution into 100% methanol. UN was synthesized to assess for preservation of the carbon and nitrogen isotope compositions of reactants (urea and nitric acid) and product UN. Based on nitrogen isotope mass balance, all UN samples contained varying amounts of excess nitric acid, making the ionic separation an essential step in the nitrogen isotope analysis. During UN synthesis experiments, isotopic composition of the reactants is preserved in the product UN, but the urea in the product UN is slightly enriched in (15)N (<1‰) relative to the reactant urea. Published isotopic compositions of UN reactants, urea and nitric acid, have large ranges (urea δ(15)N = -10.8 to +3.3‰; urea δ(13)C = -18.2 to -50.6‰; and nitric acid δ(15)N = -1.8 to +4.0‰). The preservation of isotopic composition of reactants in UN, along with a significant variability in isotopic composition of reactants, indicates that isotope ratio analysis may be used to test if urea or nitric acid collected during an investigation is a possible reactant for a specific UN sample. The carbon and nitrogen isotope ratios differ significantly between two field-collected UN samples, as well as the lab-synthesized UN samples. These observed variations suggest that this approach is useful for discriminating between materials which are otherwise chemically identical.

Forensic discrimination of photocopy and printer toners. III. Multivariate statistics applied to scanning electron microscopy and pyrolysis gas chromatography/mass spectrometry.

Copy toner samples were analyzed using scanning electron microscopy with X-ray dispersive analysis (SEM-EDX) and pyrolysis gas chromatography/mass spectrometry (Py-GC/MS). Principal component and cluster analysis of SEM data for 166 copy toner samples established 13 statistically different subgroups, with the presence or absence of a ferrite base being a major division. When toners were compared for which both SEM and reflection-absorption infrared spectral data were available, 41% of the samples could be assigned to specific manufacturers. Py-GC/MS on poly(styrene:acrylate)-based toners produced eight peaks relevant to toner differentiation. One third of the toners clustered in a small group that contained five statistically different subgroups. Of the 57 toners for which both Py-GC/MS and SEM data were available, 31 could be differentiated using the combined analytical results. The synergy of the complementary information provided by Py-GC/MS and SEM narrows matching possibilities for forensic investigations involving copied or laser printed documents.