RESUMO
In this study, a novel perovskite solar cell (PSC) architecture is presented that utilizes an HTL-free configuration with formamide tin iodide (FASnI3) as the active layer and fullerene (C60) as the electron transport layer (ETL), which represents a pioneering approach within the field. The elimination of hole transport layers (HTLs) reduces complexity and cost in PSC heterojunction structures, resulting in a simplified and more cost-effective PSC structure. In this context, an HTL-free tin HC(NH2)2SnI3-based PSC was simulated using the solar cell capacitance simulator (SCAPS) within a one-dimensional framework. Through this approach, the device performance of this novel HTL-free FASnI3-based PSC structure was engineered and evaluated. Key performance parameters, including the open-circuit voltage (Voc), short-circuit current density (Jsc), fill factor (FF), power conversion efficiency (PCE), I-V characteristics, and quantum efficiency (QE), were systematically assessed through the modulation of physical parameters across various layers of the device. A preliminary analysis indicated that the HTL-free configuration exhibited improved I-V characteristics, with a PCE increase of 1.93% over the HTL configuration due to improved electron and hole extraction characteristics, reduced current leakage at the back contact, and reduced trap-induced interfacial recombination. An additional boost to the device's key performance parameters has been achieved through the further optimization of several physical parameters, such as active layer thickness, bulk and interface defects, ETL thickness, carrier concentration, and back-contact materials. For instance, increasing the thickness of the active layer PSC up to 1500 nm revealed enhanced PV performance parameters; however, further increases in thickness have resulted in performance saturation due to an increased rate of hole-electron recombination. Moreover, a comprehensive correlation study has been conducted to determine the optimum thickness and donor doping level for the C60-ETL layer in the range of 10-200 nm and 1012-1019 cm-3, respectively. Optimum device performance was observed at an ETL-C60 ultra-thin thickness of 10 nm and a carrier concentration of 1019 cm-3. To maintain improved PCEs, bulk and interface defects must be less than 1016 cm-3 and 1015 cm-3, respectively. Additional device performance improvement was achieved with a back-contact work function of 5 eV. The optimized HTL-free FASnI3 structure demonstrated exceptional photovoltaic performance with a PCE of 19.63%, Voc of 0.87 V, Jsc of 27.86 mA/cm2, and FF of 81%. These findings highlight the potential for highly efficient photovoltaic (PV) technology solutions based on lead-free perovskite solar cell (PSC) structures that contribute to environmental remediation and cost-effectiveness.
RESUMO
In this study, a hybrid organic-inorganic perovskite solar cell (PSC) based on methylammonium germanium triiodide (MAGeI3), which is composed of methylammonium (CH3NH3+) cations and germanium triiodide (GeI3-) anions, has been numerically studied using SCAPS-1d codes. An extensive investigation of various electron transport layers (ETLs) and hole transport layers (HTLs) was conducted to identify the most optimal device configuration. The FTO/ZnOS/MAGeI3/PEDOT-WO3 structure performed the highest efficiency of all combinations tested, with an impressive optimized efficiency of 15.84%. This configuration exhibited a Voc of 1.38 V, Jsc of 13.79 mA/cm2, and FF of 82.58%. J-V characteristics and external quantum efficiency (EQE) measurements indicate that this device offers superior performance, as it has reduced current leakage, improved electron and hole extraction characteristics, and reduced trap-assisted interfacial recombination. Optimum device performance was achieved at active layer thickness of 560 nm. These findings may also serve as a basis for developing lightweight and ultra-thin solar cells, in addition to improving overall efficiency. Furthermore, a comprehensive correlation study was conducted to evaluate the optimum thickness and doping level for both ZnOS-ETL and PEDOT-WO3-HTL. The photovoltaic performance parameters of the FTO/ZnOS/MAGeI3/PEDOT-WO3 structure were analyzed over a wide temperature range (275 K to 450 K). The structure exhibited stable performance at elevated operating temperatures up to 385 K, with only minimal degradation in PCE of approximately 0.42%. Our study underscores the promise of utilizing cost-effective and long-term stability materials like ZnOS and PEDOT-WO3 alongside the toxic-free MAGeI3 perovskite. This combination exhibits significant potential for eco-friendly PSC, paving the way for the development of highly efficient ultra-thin PSC.
