RESUMO
AIM: The aim of this study was to evaluate post-core design on Stress distribution in maxillary central incisor with various designs retentive channels placed on the face of the root with no remaining coronal tooth structure. MATERIALS AND METHODS: 3 dimensional finite element model of a maxillary central incisor was developed and seven other study modes were developed. Tooth was scanned using CBCT unit, with reverse engineering software. 3D wire mesh, with ten node tetrahedral element, developed was transferred to ANASYS software. Composite was used for post-core-crown as post endodontic restoration. Mechanical properties were assigned to each component for FEA. All the materials were assumed to be isotropic, linearly elastic, homogenous and tightly bonded. A load of 100N were applied from vertical, horizontal and lateral oblique from incisal and palatal surface respectively. RESULTS: Analysis revealed that stresses were concentrated at the point of load application on crown(vertical(V) 14.35MPa, horizontal(H) 27.04 MPa and lateral oblique(L)13.75MPa) and depending on the post core design the stresses were homogenous evenly distributed over the root dentin, core and least over the post. There was variation in stress distribution under vertical horizontal and lateral oblique load. CONCLUSION: Teeth with no remaining coronal structure and by placing retentive channels on the face of the root will enable homogenous stress distribution, promote mechanical retention and stability to the post core crown post endodontic restoration.
RESUMO
PURPOSE: The purpose of the study was to evaluate by a 3-dimensional finite element analysis the load transmission to periimplant bone by a framework supported by 6 implants placed in an edentulous mandible and to compare the stress distribution for varying cantilever lengths. METHODOLOGY: A computerized model of the anterior segment of a mandible with a 6-implant-supported bridge was created in software. The length of the cantilever segment was considered as 10, 15, and 20 mm. A 150 N load was applied to the terminal point of the cantilever segment, and Von Mises stresses were analyzed along implants, framework, and bone. RESULTS: When the cantilever length was increased from 10 to 20 mm, the stress increased 79.66% in the framework, 68.16% in implants, and 59.96% and 52.81% in cortical and cancellous bones, respectively. CONCLUSION: The greatest amount of stress was seen around the distal-most region of the distal-most implant. The framework absorbed the maximum amount of stresses followed by the implants, cortical bone, and cancellous bone. Extension of the cantilever beyond 15 mm could lead to greater stress in the lingual cortical plate, which could compromise the integrity of the implants.
Assuntos
Implantes Dentários , Prótese Dentária Fixada por Implante , Simulação por Computador , Análise do Estresse Dentário , Humanos , Mandíbula , Estresse Mecânico , Suporte de CargaRESUMO
BACKGROUND: The success of dental implants depends on the manner in which stresses are transferred to the surrounding bone. An important consideration is to design an implant with a geometry that will minimize the peak bone stresses caused by standard loading. The aim of this study was to assess the influence of implant thread geometry on biomechanical load transfer and to compare the difference between two different thread designs. MATERIALS AND METHODS: A three-dimensional finite element model of D2 bone representing mandibular premolar region was constructed. Two implants of differing thread geometries, 13-mm length, and 4-mm diameter along with superstructures were simulated. One design featured fourfold microthread of 0.4-mm pitch, 0.25-mm depth in the crestal one-third; 0.8-mm pitch, 0.5-mm depth in the apical two-third. The other design had a single-pitch microthread of 0.8-mm pitch, 0.25-mm depth in the crestal one-third; 0.8-mm pitch, 0.5-mm depth in the apical two-third. A static axial load of 100-N was applied to the occlusal surface of the prosthesis. ANSYS CLASSIC 9.0 (PA,USA)software was used for stress analysis as von Mises stresses. RESULTS: A comparison of von Mises stresses between two thread designs revealed that fourfold microthread allows better stress distribution within the implant body by 43.85%, abutment by 15.68%, its superstructure by 39.70% and 36.30% within cancellous bone as compared to single-pitch microthread. The effective stress transfer to the cortical bone is lowered by 60.47% with single-pitch microthread. CONCLUSION: Single-pitch microthread dissipates lesser stresses to cortical bone while the implant body, abutment, and superstructure absorb more stress. This will have a positive influence on the bone-implant contact and contribute to preservation of crestal bone. Implant with single pitch microthread will thus be preferable to be used in areas where the amount of cortical bone available is less.
RESUMO
PURPOSE: This meta-analysis aims to systematically review and draw a comparison between conventional implant designs and "platform-switched" implants in terms of crestal bone loss. MATERIALS AND METHODS: Electronic (PubMed) and hand searches were conducted. Literature, clinical studies, and case reports pertaining to reduction of crestal bone loss and obtaining better esthetic outcome by platform switching were reviewed till October 2011. Controlled trials comparing marginal bone-level changes around platform-switched and platform-matched implants were selected. For the assessment of accuracy, meta-analysis was performed. RESULTS: The marginal bone loss around platform-switched implants was significantly lesser than platform-matched implants (mean difference [MD]: -0.34; 95% confidence interval [CI]: -0.37 to -0.30; P < 0.00001). CONCLUSIONS: According to this review and meta-analysis, platform switching seems to preserve periimplant bone and soft tissue levels. However, long-term clinical studies on the proper diameter of abutment without deformation and the effective degree of platform switching in terms of the bone resorption are still awaited.
