Evaluation of thin film microextraction based on graphene oxide/ polymer composite: Experimental and theoretical insights.

Experimental and theoretical assessments of a graphene oxide-based polymer as adsorbent for thin film microextraction (TFME) were conducted as part of this research. Graphene oxide (GO) was embedded in the organic polymer poly(styrene-co-divinylbenzene) (PS-DVB) to prepare a sorbent suitable for direct-immersion TFME. A TFME membrane coating prepared with the GO/PS-DVB sorbent and polydimethylsiloxane (PDMS) as binder was then applied for extraction of organic pollutants from aqueous and gaseous samples. The surface morphology of the TFME coating was examined by scanning electron microscopy (SEM). Various TFME parameters influencing extraction efficiency, such as extraction time and temperature, desorption temperature, and ionic strength, were investigated and optimized. In a comparison of TFME membranes, the GO/PS-DVB/PDMS TFME membrane was shown to yield higher extraction efficiencies for the targeted analytes than the pure PDMS and DVB/PDMS TFME membranes. The calibration graphs of the organic pollutants displayed linearity for most of the target analytes within the 10-2000 ng L-1 concentration range. The repeatability (RSD %, n = 5) and reproducibility (RSD %, n = 3) of the method were in the ranges of 2.2-5.9 %, and 3.2-8.5 %, respectively, at a concentration level of 500 ng L-1, whereas accuracy (%) ranged between 79.8 and 119 %. The developed method was successfully applied for determinations of organic pollutants in tap water, lake water, and wastewater samples. Furthermore, the impact of mass transfer kinetics on extractions by the GO/PS-DVB/PDMS TFME membrane from gaseous samples was theoretically discussed and experimentally verified. The results of this work demonstrate that the GO/PS-DVB/PDMS TFME method is a simple, efficient, and environmentally friendly method for pre-treatment of organic pollutants.

Performance Evaluation of Extraction Coatings with Different Sorbent Particles and Binder Composition.

Binders are critical components used in the preparation of a range of extraction devices, including solid-phase microextraction (SPME) devices. While the main role of a binder is to affix the sorbent particles to the selected support, it is critical to select the optimal binder to ensure that it does not negatively impact the coating's particle sorption capability. This work presents the first comprehensive investigation of the interactions between binders and solid sorbent particles as these interactions can significantly impact the performance of the coating. Specifically, the findings presented herein provide a better understanding of the extraction mechanisms of composite coatings and new rules for predicting the particle adhesion forces and binder distribution in the coating. The influence of binder chemistry on coating performance is investigated by examining a selection of the most used binders, namely, polydimethylsiloxane (PDMS), polyacrylonitrile (PAN), poly(vinylidene difluoride) (PVDF), polytetrafluoroethylene amorphous fluoroplastics (PTFE AF 2400), and polybenzimidazole (PBI). The solid particles (e.g., hydrophilic-lipophilic balanced (HLB) and C18) used in this work were selected for their ability to provide optimal extraction coverage for a broad range of analytes. The results show that PDMS does not change the properties of the solid particles and that the binder occupies a negligible volume due to shrinking after polymerization, resulting in the solid particles making up most of the coating volume. Hence, the coating sorption characteristics correspond closely to the properties of the selected solid particles. On the other hand, the results also showed that PTFE AF 2400 can interact with the active surface of the sorbent, leading to the deactivation of the sorbent particles. Therefore, the extraction performance and permeability coefficients decrease as the size of the penetrant increases, indicating a rigid porous structure. The results of this study can aid in the optimization of SPME devices as they provide reference values that can be used to determine the optimal binder and the sorbent affinity for the targeted compounds. Finally, the present work also provides the broader scientific community with a strategy for investigating the properties of sorbent particle/binder structures and defines the characteristics of a good coating/membrane by analyzing all parameters such as kinetics, thermodynamic equilibria, and morphology.

Polybenzimidazole: a novel, fluorocarbon-free, SPME sorbent binder with good thermal and solvent resistance properties for GC and LC analysis.

A novel solid-phase microextraction (SPME) coating is presented that uses polybenzimidazole (PBI) as a binder to immobilize micro-size sorbent particles onto a support. An evaluation of the developed binder's thermal and solvent desorption capabilities demonstrated its compatibility with both gas and liquid chromatography (GC and LC). The incorporation of hydrophilic-lipophilic balanced (HLB) particles provided optimal extraction coverage for an array of chemically diverse analytes possessing a range of hydrophobicities and molecular weights. The developed binder's performance was assessed by comparing it to a selection of binders commonly used in the literature, including polydimethylsiloxane (PDMS) and polyacrylonitrile (PAN), as well as the more recently developed polyvinylidene fluoride (PVDF) and polytetrafluoroethylene amorphous fluoroplastic (PTFE AF 2400). The results revealed that PBI provides better performance compared to PVDF and PTFE AF 2400 in terms of its environmental impact, while also being convenient for use in coating preparation and offering good matrix compatibility. The thermal analysis revealed that PBI exhibited more than 93% weight retention at 550 °C, which is superior to PVDF's 80.07% weight retention at 393.78 °C. To the best of our knowledge, this work is the first to use PBI as a particle binder in SPME coatings. The PBI coating maintained high extraction efficiencies under extreme conditions with pH values of 3 and 12. The performance of PBI in combination with HLB was assessed by employing it to extract several drugs of abuse and McReynolds compounds for LC and GC analysis, respectively. The results indicated that PBI performs similarly to PAN for LC but is outperformed by PDMS in GC applications with respect to extraction and desorption kinetics. Nonetheless, the thermal and solvent desorption results indicated that PBI can be used for both applications, as it remains stable at temperatures over 350 °C and is stable when solvent desorption is applied.

Coupling of Solid-Phase Microextraction Directly to Mass Spectrometry via an Improved Microfluidic Open Interface to Facilitate High-Throughput Determinations.

Mass spectrometry analysis can be performed by introducing samples directly to mass spectrometry, allowing the increase of the analysis throughput; however, some disadvantages of direct-to-mass spectrometry analysis include susceptibility to matrix effects and risk of instrument contamination from inadequate sample preparation. Solid-phase microextraction is one of the most suitable sample preparation methods for direct-to-mass spectrometry analysis, as it offers matrix-compatible coatings which ensure analyte enrichment with minimal or no interference from matrix. One of the ways solid-phase microextraction can be coupled directly to mass spectrometry is via a microfluidic open interface. This manuscript reports improvements made to the initial microfluidic open interface design, where the system components have been simplified to mostly commercially available materials. In addition, the analysis of samples has been automated by implementing software that fully controls the analysis workflow, where the washing procedure is optimized to completely reduce the carryover. Herein, the extraction and desorption time profiles from thin and thick SPME devices was studied where the overall workflow consisted of high-throughput sample preparation of 1.3 min per 96 samples and <1 min per sample instrumental analysis.

Urinary bio-monitoring of aromatic amine derivatives by new needle trap device packed with the multi-component adsorbent.

Aromatic amines are a large group of chemical compounds that have attracted the attention of researchers due to their toxicity and carcinogenicity. This study aimed to develop an efficient method for sampling and analysis of aromatic amines (Aniline, N, N-dimethylaniline, 2-chloroaniline, and 3-chloroaniline) from the vapour phase (headspace) of urine samples. For the implementation of this plan, a needle trap device packed with the three-component adsorbent consisting of nano-Hydroxy Apatite (nHA), Zeolite (Ze), and Metal-Organic Framework (MOF) equipped with GC-FID was employed for the first phase. Examination of the prepared adsorbents was performed by FT-IR, PXRD, and FE-SEM techniques. The optimal value of considerable parameters such as time and temperature of extraction, salt content, and pH were established using the Response Surface Methodology-Central Composite Design (RMS-CCD) method. In this way, the optimal extraction of targeted analytes was accomplished in 41 min at 41 °C with NaCl content of 33.0% (w/v) and pH: 13.0, respectively. Also, the repeatability and reproducibility of the method were calculated to be in the range of 2.2-7.1% and 3.9-8.1%, respectively, which indicates the acceptable precision of the method. Also, the limit of detection (LOD) and limit of quantification (LOQ) were determined in the range of 0.3-32.0 ng.L-1 and 0.8-350.0 ng.L-1, respectively, which proves the high sensitivity of the proposed method. Furthermore, the recovery percent of the extracted analytes was concluded in the range of 97.0-99.0% after 6 and 30 days of the sampling and storage at 25 °C and 4 °C, respectively. Finally, the designed procedure was employed in the analysis of the above-mentioned aromatic amines in the real urine samples. The achieved results illustrate that the three-component absorbent system (nHA;Ze;MOF@NTD) can be introduced as an efficient, fast-response, sensitive, and versatile procedure for trace analysis of the different aromatic amine compounds in public and occupational health.

Rapid Sample Screening Method for Authenticity Controlling of Vanilla Flavours Using Liquid Chromatography with Electrochemical Detection Using Aluminium-Doped Zirconia Nanoparticles-Modified Electrode.

A rapid and sensitive technique for frauds determination in vanilla flavors was developed. The method comprises separation by liquid chromatography followed by an electrochemical detection using a homemade screen-printed carbon electrode modified with aluminium-doped zirconia nanoparticles (Al-ZrO2-NPs/SPCE). The prepared nanomaterials (Al-ZrO2-NPs) were characterized by using X-ray diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray (EDX). This method allows for the determination of six phenolic compounds of vanilla flavors, namely, vanillin, p-hydroxybenzoic acid, p-hydroxybenzaldehyde, vanillyl alcohol, vanillic acid and ethyl vanillin in a linear range between 0.5 and 25 µg g-1, with relative standard deviation values from 2.89 to 4.76%. Meanwhile, the limits of detection and quantification were in the range of 0.10 to 0.14 µg g-1 and 0.33 to 0.48 µg g-1, respectively. In addition, the Al-ZrO2-NPs/SPCE method displayed a good reproducibility, high sensitivity, and good selectivity towards the determination of the vanilla phenolic compounds, making it suitable for the determination of vanilla phenolic compounds in vanilla real extracts products.

Thin-film microextraction combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry screening for presence of multiclass organic pollutants in drinking water samples.

Organic compounds in drinking water can be potentially hazardous. In this study, we demonstrate for the first time that combining in-bottle thin-film microextraction (TFME), comprehensive two-dimensional gas chromatography, and time-of-flight mass spectrometry (GC × GC-TOFMS) can produce a powerful, green tool for determining multiple organic pollutants in drinking water and monitoring changes in water samples after treatment with a water purification system. In the developed approach, water is added to an amber sampling bottle containing TFME membranes and left to sit until equilibration is achieved. Once equilibration has been achieved, the membranes are withdrawn, and the extracted compounds are quantified via thermal desorption in the GC × GC-TOFMS system. This approach enabled a large number of organic compounds with a wide range of physicochemical properties to be identified based on their mass spectra. A series of drinking water samples (raw water, water after softener filter, and drinking water) were collected from a standard house faucet in order to analyze changes following treatment with a water purification system. The developed strategy was also applied to identify the concentrations of the 9 selected organic compounds in the water samples. Ultimately, the in-bottle TFME-GC × GC-TOFMS method is straightforward and provides comparable performance to other methods for low-level analyses of organic pollutants in drinking water samples.

Untargeted analysis of microbial metabolites and unsaturated fatty acids in salmon via hydrophilic-lipophilic balanced solid-phase microextraction arrow.

The ability to detect spoilage and the nutrient content of salmon is critical for ensuring food safety and determining market value. In this paper, we document the development of a hydrophilic-lipophilic balanced solid-phase microextraction arrow that offers better extraction performance than two other commercial devices. The devices were also compared using two operational models: headspace microextraction and direct immersion. The multidimensional statistical analysis and heatmap analysis for the headspace microextractions showed that the content levels of volatile metabolites including hydrocarbons, alcohols, ketones, acids, amino acids, and ethers increased with longer storage times, indicating an increase in the activity of spoilage-associated bacteria, such as gram-negative bacteria. For the direct immersion tests, important nutrients, including lipids, sterols, and squalene, were directly extracted from the salmon fillets with high efficiency. Thus, the developed method provides a simple and easy time-domain monitoring strategy for testing the freshness and quality of salmon for consumers.

Vacuum-assisted headspace thin-film microextraction: Theoretical formulation and method optimization for the extraction of polycyclic aromatic hydrocarbons from water samples.

The thin films used in headspace thin-film microextraction (HS-TFME) enable higher sensitivity and superior extraction rates compared to other microextraction approaches, largely due to their greater surface area-to-volume ratio and extraction-phase volume. Nonetheless, analytes exhibiting a low affinity for the headspace and/or large partitioning between the extraction phase and headspace will still require more time to reach equilibrium. In this paper, we detail the development of a new method, termed as vacuum-assisted HS-TFME (Vac-HS-TFME), and we demonstrate how its use of vacuum conditions can accelerate the extraction kinetics of analytes with long equilibration times. The pressure-dependence of the extraction process was formulated and related to improvements in gas-phase diffusivity when lowering the total pressure. Four low-molecular-weight polycyclic aromatic hydrocarbons (PAHs) were used to experimentally verify the improvements in extraction efficiencies enabled by Vac-HS-TFME (vs. HS-TFME). To this end, the effects of temperature and extraction time on Vac-HS-TFME were investigated, with the results being compared to those obtained via regular HS-TFME. Furthermore, the use of a high-capacity sorbent in TFME allowed the positive effects of temperature and vacuum conditions to be combined successfully. Extraction-time profiles constructed at 30 and 50 °C revealed substantial acceleration in the overall extraction kinetics when sampling under vacuum conditions. At 50 °C, all of the analytes extracted via Vac-HS-TFME reached equilibrium within 45 min, whereas only two reached this state under atmospheric pressure. Vac-HS-TFME's analytical performance was evaluated under optimized conditions, and the results were compared to those obtained with regular HS-TFME. The findings revealed that for the two lighter PAHs, the performance of the two methods was similar since they were extracted close or at equilibrium. However, the calibration models for the two heavier PAHs tested here were linear over a wider concentration range (50-10000 ng L-1) when using Vac-HS-TFME, had superior intra-day repeatability (7.4% and 6.7% vs. 11% and 9.3% with regular HS-TFME), and the limits of detection were lower compared to regular HS-TFME (15 and 11 ng L-1 compared to 136 to 100 ng L-1 with regular HS-TFME). Finally, the analysis of spiked wastewater effluent samples showed that the matrix did not affect extraction. The proposed Vac-HS-TFME approach combines the advantages of low-pressure sampling and high-capacity sorbent, and has a great potential for future applications in food, flavour, environmental, and biological analyses.

Profiling of Unsaturated Lipids by Raman Spectroscopy Directly on Solid-Phase Microextraction Probes.

Lipids play a critical role in cellular signaling, energy storage, and the construction of cellular membranes. In this paper, we propose a novel on-site approach for detecting and differentiating enriched unsaturated lipids based on the direct coupling of SPME probes with Raman spectroscopy. To this end, different SPME particles, namely, hydrophilic-lipophilic balanced (HLB), mixed-mode (C8-SCX), and C18, were embedded in polyacrylonitrile (PAN) and tested for their efficacy as biocompatible coatings. The C18/PAN coating showed less background interference compared to the other sorbent materials during the analysis of unsaturated lipids. In addition, different SPME parameters that influence extraction efficiency, such as extraction temperature, extraction time, and washing solvent, were also investigated. Our results indicate a clear dependence between the Raman band intensity related to the number of double bonds in fatty acids mixture and the number of double bonds in a fatty acid. Our findings further show that Raman spectroscopy is especially useful for the analysis of lipid unsaturation, which is calculated as the ratio of n(C═C)/n(CH2) using the intensities of the Raman bands at 1655/1445 cm-1. Furthermore, the developed protocol reveals great SPME activity and high detection ability for several unsaturated lipids in different complex matrixes, such as cod liver oil. Finally, the applicability of this technology was demonstrated via the characterization of cod liver oil and other vegetable oils. Thus, the proposed SPME-Raman spectroscopy approach has a great future potential in food, environmental, clinical, and biological applications.

The Effect of Sorbent Particles in a Binder on the Mass Transfer Kinetics in Separation Media: In Silico Study and Experimental Verification.

Selecting the optimal binder and the sorbent affinity for selected compounds can cause the composite to behave either as an efficient extraction coating, as a permeable membrane, or as an impermeable barrier. If the compound partitions onto the sorbent with high preference, it becomes stationary and the composite behaves as an impermeable barrier, while appropriately optimized affinity will result in effective permeation. To understand this phenomenon, we utilize solid-phase microextraction to characterize the mass transfer attributes of different separation composites. Our results indicate that for strong sorbents, the extraction rate is primarily controlled by the diffusion in the extraction phase rather than the sample matrix, even if it is relatively thin. Low analyte diffusion is caused by the retarding force generated by the partitioning of analytes into the sorbent, as migration through the composite is driven by the unbound form of the compound in the binder. One of the main contributions of this work is that an understanding of the extraction composite parameters that control mass transfer during extraction enables better optimization of binder/sorbent extraction phase composition for a given application. Another contribution of this work shows how a heterogeneous coating model can be simplified into a homogeneous coating model. The developed models enable an enhanced understanding of mass transfer kinetics, and they provide insight into how to optimize the extraction phase parameters for a given method involving sorbent particles in polymeric media, including membranes and paints, in addition to extraction coatings.

Surface Polymers on Multiwalled Carbon Nanotubes for Selective Extraction and Electrochemical Determination of Rhodamine B in Food Samples.

In this study, we combine magnetic solid phase extraction (MSPE), with the screen-printed carbon electrode (SPCE) modified by a molecular imprinted polymer (MIP) for sensitive and selective extraction and electrochemical determination of Rhodamine B in food samples. A magnetic solid phase extraction (MSPE) was carried out using magnetic poly(styrene-co-divinylbenzene) (PS-DVB) and magnetic nanoparticles (MNPs) synthetized on the surface of multiwalled carbon nanotubes (MWCNTs). An MIP was prepared on the surface of MWCNTs in the presence of titanium oxide nanoparticles (TiO2NPs) modifying the SPCE for the rapid electrochemical detection of Rhodamine B. The MIPs synthesis was optimized by varying the activated titanium oxide (TiO2) and multiwalled carbon nanotubes (MWCNTs) amounts. The MSPE and electrochemical detection conditions were optimized as well. The present method exhibited good selectivity, high sensitivity, and good reproducibility towards the determination of Rhodamine B, making it a suitable method for the determination of Rhodamine B in food samples.

Determination of selected volatile terpenes in fish samples via solid phase microextraction arrow coupled with GC-MS.

A high-efficiency enrichment method is required for determination of trace-level volatile terpenes in fish tissue, since the presence of such compounds in fish at elevated levels may induce bad sensory acceptance of fish meat, thus degrading its customer acceptance and consequently, its market value. In this study, a solid-phase microextraction (SPME) arrow configuration using a thick sorbent coating (120 µm, PDMS/CWR) was applied to enrich selected terpenes, namely α-pinene, limonene, linalool, and citronellol, in fish tissue (Oreochromis niloticus). Due to the thicker coating of the SPME arrow, a longer extraction time of 60 min was required to reach equilibrium extraction in comparison to the traditional fiber configuration. SPME conditions such as extraction temperature (60 °C), desorption temperature (250 °C), and salt effect (10% NaCl) were optimized for the developed application using the arrow configuration. The developed method exhibited good linearity at a concentration range of 5.0-500.0 µg L-1 for α-pinene and limonene, and 50.0-500.0 µg L-1 for linalool and citronellol. In addition, the coefficients of determination (R2) for all terpenes ranged from 0.9990 to 0.9999. The developed method was shown to be robust with good inter-day reproducibility in the range of 3.6-8.3%. Method sensitivity was assessed in terms of limits of detection (LODs) and limits of quantification (LOQs), with higher sensitivity achieved for α-pinene and limonene (LODs of 1.7 µg L-1) in comparison to linalool (LOD, 5.0 µg L-1) and citronellol (LOD, 17.0 µg L-1). Theoretical calculations verified that the increased coating thickness afforded by the arrow configuration can enable higher method sensitivity and widen the range of detected compounds for the headspace SPME.

Development and validation of an improved, thin film solid phase microextraction based, standard gas generating vial for the repeatable generation of gaseous standards.

This work presents the development and validation of novel thin film solid phase micro extraction (TF-SPME) based standard gas generating vials suitable for repeatable generation of gaseous standards for GC-MS analysis and quality control. The vials were developed using carbon mesh membranes loaded with pure polydimethylsiloxane (PDMS), divinylbenzene (DVB/PDMS), hydrophilic-lipophilic balance (HLB/PDMS), and carboxen (Car/PDMS) sorbents that were then spiked with modified McReynolds standards including benzene, 2-pentanone, 1-nitropropane, pyridine, 1-pentanol, octane, dodecane, and hexadecane. Sorbent strength was determined to follow the aforementioned order, with pure PDMS presenting the weakest sorption capabilities and Car/PDMS the strongest. While the weaker, pure PDMS based gas generating vials transferred an instrument-overloading amount of McReynolds probes to the 1.1 mm DVB/PDMS SPME arrows used for extraction, vials prepared using Car/PDMS TF-SPME as a sorbent failed to provide consistently detectable amounts of analytes less volatile than 1-nitropropane. The DVB/PDMS and HLB/PDMS based vials were found to maintain optimal sorption capabilities for the tested analytes, providing a sorption strength strong enough to not exhibit any depletion in 10 replicate runs, while still delivering a consistent amount of all the regular McReynolds components. Moreover, with intra-vial%RSDs of 5% or less for all analytes tested, these HLB and DVB vials were found to deliver very good repeatability. After purposely submitting vials to 200 accelerated depletion extractions (1.1 mm DVB/PDMS arrow at 55 °C for 3 min), vials prepared with DVB/PDMS were found to deplete by 33%, 38%, 34%, 33%, 40%, and 33% while vials prepared with HLB/PDMS were found to deplete by 21%, 16%, 12%, 31%, 16% and 0% for benzene, 2-pentanone, 1-nitropropane, pyridine, 1-pentanol, and octane, respectively. When user typical extractions conditions were used instead (50/30 µm DVB/Car/PDMS SPME fiber at 35 °C for 1 min), no depletion could be observed from the HLB/PDMS based vial while%RSDs ranged from 1.1-3.0% after the 300 extraction/desorption cycles. Finally, in efforts to demonstrate its real world applicability, the DVB/PDMS vial was used to evaluate the inter-fiber repeatability of commercial DVB/PDMS SPME arrows, with results demonstrating that arrows from a single package were statistically similar (ANOVA at 95% confidence).

Systematic Evaluation of Different Coating Chemistries Used in Thin-Film Microextraction.

A systematic evaluation of eight different coatings made of solid phase extraction (SPE) and carbon-based sorbents immobilized with polyacrylonitrile in the thin-film microextraction (TFME) format using LC-MS/MS was described. The investigated coatings included graphene, graphene oxide, multi-walled carbon nanotubes (MWCNTs), carboxylated MWCNTs, as carbon-based coatings, and polystyrene-divinylbenzene (PS-DVB), octadecyl-silica particles (C18), hydrophilic-hydrophobic balance particles (HLB) and phenyl-boronic acid modified particles (PBA), as SPE-based coatings. A total of 24 compounds of diverse moieties and of a wide range of polarities (log P from -2.99 to 6.98) were selected as probes. The investigated coatings were characterized based on their extraction performance toward the selected probes at different pH values and at optimized desorption conditions. In the case of SPE-based coatings, PS-DVB and HLB exhibited a balanced extraction for compounds within a wide range of polarities, and C18 showed superior extraction recoveries for non-polar analytes. Carbon-based coatings showed high affinity for non-polar compounds given that their main driving force for extraction is hydrophobic interactions. Interestingly, among the studied carbon-based coatings, graphene oxide showed the best extraction capabilities toward polar compounds owing to its oxygen-containing groups. Overall, this work provided important insights about the extraction mechanisms and properties of the investigated coatings, facilitating the coating selection when developing new TFME applications.

LC-MS determination of catecholamines and related metabolites in red deer urine and hair extracted using magnetic multi-walled carbon nanotube poly(styrene-co-divinylbenzene) composite.

A novel analytical methodology for the extraction and determination of catecholamines (dopamine, epinephrine and norepinephrine) and their metabolites DL-3,4-dihydroxyphenyl glycol and DL-3,4-dihydroxymandelic acid by LC-MS is developed and validated for its application to human and animal urine and hair samples. The method is based on the preliminary extraction of the analytes by a magnetic multi-walled carbon nanotube poly(styrene-co-divinylbenzene) composite. This is followed by a <9 min chromatographic separation of the target compounds in an Onyx Monolithic C18 column using a mixture of 0.01% (v/v) heptafluorobutyric acid in water and methanol at 500 µL min-1 flow rate. Detection limits within range from 0.055 to 0.093 µg mL-1, and precision values of the response and retention times of analytes were >90%. Accuracy values comprised the range 79.5-109.5% when the analytes were extracted from deer urine samples using the selected MMWCNT-poly(STY-DVB) sorbent. This methodology was applied to real red deer urine and hair samples, and concentrations within range from 0.05 to 0.5 µg mL-1 for norepinephrine and from 1.0 to 44.5 µg mL-1 for its metabolite 3,4-dihydroxyphenyl glycol were calculated. Analyses of red deer hair resulted in high amounts of 3,4-dihydroxyphenyl glycol (0.9-266.9 µg mL-1).

Analytical control of Rhodamine B by SERS using reduced graphene decorated with copper selenide.

A novel approach for the decoration of reduced graphene oxide with copper selenide (CuSe-rGO), using supercritical carbon dioxide (sc-CO2) as a medium, was developed and proposed as a new substrate for surface-enhanced Raman spectroscopy (SERS) to determine Rhodamine B in chili powder. The synthesized materials graphene oxide (GO), reduced graphene oxide (rGO) and CuSe-rGO were characterized by Raman spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). All SERS spectra were obtained by using a portable Raman spectrometer. The procedure presented involves a simple and rapid sample pretreatment in order to determine Rhodamine B in chili powder, with a limit of quantification of 44.5 ng g-1. The recovery values of the proposed method resulted in the 96% to 99% range, with RSD values from 2.4% to 3.0%. The developed SERS active hybrid substrate has an enhancement factor higher than those using gold or silver nanoparticles, providing a clear improvement in the sensitivity.

Unique evolution of vitamin A as an external pigment in tropical starlings.

Pigments are largely responsible for the appearance of organisms. Most biological pigments derive from the metabolism of shikimic acid (melanins), mevalonic acid (carotenoids) or levulinic acid (porphyrins), which thus generate the observed diversity of external phenotypes. Starlings are generally dark birds despite iridescence in feathers, but 10% of species have evolved plumage pigmentation comprising bright colors that are known to be produced only by carotenoids. However, using micro-Raman spectroscopy, we have discovered that the bright yellow plumage coloration of one of these species, the Afrotropical golden-breasted starling Cosmopsarus regius, is not produced by carotenoids, but by vitamin A (all-trans-retinol). This is the first organism reported to deposit significant amounts of vitamin A in its integument and use it as a body pigment. Phylogenetic reconstructions reveal that the retinol-based pigmentation of the golden-breasted starling has independently appeared in the starling family from dark ancestors. Our study thus unveils a unique evolution of a new class of external pigments consisting of retinoids.

Unprecedented high catecholamine production causing hair pigmentation after urinary excretion in red deer.

Hormones have not been found in concentrations of orders of magnitude higher than nanograms per milliliter. Here, we report urine concentrations of a catecholamine (norepinephrine) ranging from 0.05 to 0.5 g/l, and concentrations of its metabolite DL-3,4-dihydroxyphenyl glycol (DOPEG) ranging from 1.0 to 44.5 g/l, in wild male red deer Cervus elaphus hispanicus after LC-MS analyses. The dark ventral patch of male red deer, a recently described sexually selected signal, contains high amounts of DOPEG (0.9-266.9 mg/l) stuck in the hairs, while DOPEG is not present in non-darkened hair. The formation of this dark patch is explained by the chemical structure of DOPEG, which is a catecholamine-derived o-diphenol susceptible to be oxidized by air and form allomelanins, nitrogen-free pigments similar to cutaneous melanins; by its high concentration in urine; and by the urine spraying behavior of red deer by which urine is spread through the ventral body area. Accordingly, the size of the dark ventral patch was positively correlated with the concentration of DOPEG in urine, which was in turn correlated with DOPEG absorbed in ventral hair. These findings represent catecholamine concentrations about one million higher than those previously reported for any hormone in an organism. This may have favored the evolution of the dark ventral patch of red deer by transferring information on the fighting capacity to rivals and mates. Physiological limits for hormone production in animals are thus considerably higher than previously thought. These results also unveil a novel mechanism of pigmentation based on the self-application of urine over the fur.

A simple poly(styrene-co-divinylbenzene)-coated glass blood spot method for monitoring of seven antidepressants using capillary liquid chromatography-mass spectrometry.

A simple, rapid, selective and sensitive monitoring method for the simultaneous determination of the widely-prescribed antidepressants agomelatine, bupropion, citalopram, fluoxetine, mirtazapine, paroxetine, trazodone in just a human blood drop is here developed and validated. This methodology is based on the use of lab manufactured poly(styrene-co-divinylbenzene)-coated glass (PS-DVB) blood spot for the extraction of the analytes and their subsequent separation and detection by capillary liquid chromatography-mass spectrometry (CLC-MS). Briefly, 10 mm-side squares were punched out from blood spots collected on glass substrate coated by 10 µg of the PS-DVB polymer and eluted with 1.0 mL of 2.0% acetic acid in methanol. The analytes were then separated and detected in less than 20 min by capillary CLC-MS using a Jupiter 4 µm Proteo 90 Šcolumn and water: acetonitrile (20:80 v/v) and ammonium acetate (5 mM, pH 3.0) as mobile phase. Limit of detection (LOD) ranged from 0.018 to 0.038 µg mL-1, and remarkable precision values for the responses and retention times lower than 5.89% and 1.92% were calculated, respectively. Moreover, accuracy values ranging between 85% and 104% were obtained.