Expansion of nanotechnology for dentistry: effect of colloidal platinum nanoparticles on dentin adhesion mediated by 4-META/MMA-TBB.

PURPOSE: To investigate the effect of Colloidal Platinum Nanoparticles (CPN) on the bond strength between dentin and 4-META/MMA-TBB resin using different concentrations of CPN. MATERIALS AND METHODS: Twenty-five extracted human third molars were stored in 0.5% chloramine T. The occlusal dentin slices were prepared by grinding occlusal surfaces of each tooth and polishing with 600-grit silicon carbide paper under running water. One control and four experimental groups (2 specimens per group) were used as follows: a) dentin surfaces treated with 10-3 solution, followed by rinsing with water and subsequently an acrylic rod bonded with hand-mixed 4META/MMA-TBB resin (Super-Bond C&B, Sun Medical) (control); b) dentin surfaces treated with 10-3 etching solution, followed by rinsing with water and application of CPN (100% or 10%) as a primer solution for 60 s and rinsed with water for 20 s, then an acrylic rod bonded with Super-Bond C&B(Etch-CPN [100% or 10%]); c) dentin surfaces treated with CPN (100% or 10%) for 60 s, rinsed with water for 20 s, followed by application of 10-3 solution, then an acrylic rod bonded with Super-Bond C&B (CPN-Etch [100% or 10%]). After storage in 37°C water, specimens were sectioned into beams (cross-sectional area: 1 mm2) for microtensile bond strength testing at a crosshead speed of 1mm/min. The data were analyzed using the Games-Howell method (p < 0.05; n = 15). RESULTS: Etch-CPN (100), CPN-Etch(100) and CPN-Etch (10) showed significantly higher bond strengths compared to the control. When using 10% CPN, the highest bond strength was demonstrated. The bond strength of 4META/MMA-TBB resin was approximately doubled by CPN application. CONCLUSION: The results of this study showed that higher bond strengths are obtained when treating dentin with a lower concentration of CPN. Further evaluation to optimize conditions such as the application time and rinsing time are required.

Effect of application time of colloidal platinum nanoparticles on the microtensile bond strength to dentin.

The purpose of this study was to investigate the effect of application time of colloidal platinum nanoparticles (CPN) on bond strength. Dentin surfaces were subjected to one of the following treatments: (A) Etching with 10% citric acid-3% FeCl(3 )solution (10-3 solution); (B) Etching with 10-3 solution followed by applying CPN as a primer solution for 10, 20, 30, or 60 seconds; and (C) Priming with CPN for 10, 20, 30, or 60 seconds followed by etching with 10-3 solution. An acrylic rod was bonded to each treated dentin surface using 4-META/MMA-TBB resin. Bonded specimens were sectioned into beams for microtensile bond strength testing. In groups (B) and (C), highest bond strength was obtained when dentin surfaces were treated with CPN for 30 seconds. This meant that the CPN primer solution either enhanced the penetration of resin into dentin or the degree of conversion of 4-META/MMA-TBB resin. Within the limitations of this study, treatment with 0.1 mN CPN primer solution followed by 20 seconds of water rinsing resulted in high bond strength.

Ten-years degradation of resin-dentin bonds.

The purpose of this study was to evaluate the durability of resin-dentin bonds in 10-yr water-storage testing. Resin-dentin bonded bulk specimens were prepared using six commercially available resin adhesives. The resin-dentin bonded specimens were stored in water for 24 h (control group) or for 10 yr (experimental groups). After each storage period, the specimens were sectioned to make specimen beams and then subjected to a microtensile bond test. After the bond test, fractured surfaces were examined by scanning electron microscopy (SEM). In addition, interfacial observation of silver nanoleakage was performed using the backscatter electron mode of SEM. The bond strengths of four of the six adhesive systems tested decreased significantly after 10 yr. However, no significant bond-strength reduction was recorded for the other two systems. The interfacial observations showed water tree propagation in the bonding resin layer as a typical morphological change after aging for five of the six adhesives tested. Water tree propagation may be a symptom of degradation in the resin bonding layer of resin-dentin bonds.

Effect of monomer composition on crystal growth by resin containing bioglass.

This study evaluated the effect of resin monomer composition on crystal growth at the interface between the resin/bioglass composites and water. Light-cured resin that contained 2-bis[4(2-hydroxy-3-methacryloyloxy-propyloxy)-phenyl], 2-hydroxyethyl methacrylate, and triethylene glycol dimethacrylate with different compositions were used. Resin/bioglass composites were prepared with 40 mass% bioglass and 60 mass% resin. The resin/bioglass composites were stored in deionized distilled water for 24 h (control group) or 3-12 months (experimental groups). After water storage, the disk surfaces were examined by light- and scanning electron microscopy. Chemical states of the crystals were analyzed by laser-Raman spectroscopy and micro-X-ray diffractometry. The microscopic analysis showed crystal on the resin disks surface after six months of water storage for hydrophilic resins. However, there was no crystal formation in the control and the experimental groups of specimens of hydrophobic resins. Raman analysis showed the chemical states of the crystals formed on the resin matrix and bioglass to be different. The micro-X-ray analysis of crystals on resin disks identified them to be calcium carbonate. This crystal formation occurred in water instead of simulated body fluid. In conclusion, the resin monomer compositions affected the ability to induce crystal growth on the surfaces of disks containing bioglass.

Measurements of volatile compound contents in resins using a moisture analyzer.

The contents of volatile adhesive compounds, such as water, solvents, and residual unpolymerized monomers, affect the integrity and durability of adhesive bonding. However, there is no method available that can be used to rapidly assess the residual solvent or water contents of adhesive resins. This study examined the effectiveness of a digital moisture analyzer to measure the volatile compound contents of resins. Five self-etching adhesives and seven experimental light-cured resins prepared with different contents (0, 10, and 20% by weight) of water or solvents (acetone and ethanol) were examined in this study. The resins were prepared using different methods (with and without air blast or light-curing) to simulate the clinical conditions of adhesive application. Resin weight changes (% of weight loss) were determined as the residual volatile compound contents, using the moisture analyzer. After the measurements, the resin films were examined using a scanning electron microscope. The weight changes of the resins were found to depend on the amount of water or solvents evaporating from the resin. Water and solvents were evaporated by air blast or light-curing, but some of the water and solvents remained in the cured resin. The moisture analyzer is easy to operate and is a useful instrument for using to measure the residual volatile compound contents of adhesive resin.

Improved bond performance of a dental adhesive system using nano-technology.

Since adhesive technology was introduced into dental field, metal-based restoration has been gradually replaced by metal-free restoration. Using the adhesive technology, minimum invasive technique has been possible in daily clinical practice as well as esthetic tooth-colored restorations have become very popular all over the world.One of the current issues of the dental adhesive is durability of bond between tooth structure and adhesive resin. Several approaches to overcome the issues have been carried out. Self-etching approach is believed to create durable bond because demineralization of superficial tooth surface is very shallow. Other approach is to utilize the inhibitor of enzymes which are suggested to catalyze the decomposition of resin composites and are always secreted within the oral environment.In the present study, Colloidal Platinum Nanoparticles (CPN) was applied before the application of 4-META/MMA-TBB resin cement as the third possibility to prolong the durability of bond. This implies that the use of the CPN solution would create higher conversion at the interface compared with conventional bonding procedures.

Papilla preservation technique combined with Emdogain in the treatment of intrabony defects: a novel treatment regimen for chronic periodontitis.

BACKGROUND: Regenerative therapy with enamel matrix proteins derivative (EMD) was shown to induce periodontal regeneration in intrabony defects. However, the contribution of papilla preservation technique (PPT), to the clinical outcome of regenerative therapy is still not clarified. Therefore, we conducted the present study to evaluate clinically measurable results of a combined therapy by PPT and EMD in the treatment of isolated intrabony defects. METHODS: Sixty isolated intrabony defects in 25 patients were surgically assessed with EMD and PPT. The clinical parameters: clinical attachment level (CAL), probing depth (PD) and gingival recession (GR) were evaluated at baseline and at three years. RESULTS: The primary outcome variable was CAL. The sites treated with enamel matrix proteins demonstrated mean CAL change from 6.6+/-1.2 mm to 3.4+/-1.3 mm (p<0.001) and the mean PD was reduced from 5.9+/-1.0 mm to 2.7+/-0.8 mm (p<0.001) after three years. The mean GR decreased from 0.71+/-1.2 mm to 0.64+/-1.1 mm (p<0.821). CONCLUSIONS: The results of the present case cohort study indicate that PPT combined with EMD resulted in significant improvement of the clinical parameters in the treatment of intrabony defects in chronic periodontitis.

Effect of a new thermal cycling method on bond strength of two-step self-etching adhesive systems.

The purpose of this study was to examine the effect of a new thermal cycling method using PCR thermal cycler on the durability of two-step self-etching adhesive systems. Beam specimens for microtensile bond strength test were inserted into PCR tubes with distilled water. Thermal cycling (0, 1000, 2000, and 3000 cycles) was done with the PCR program at two different temperatures of 5 and 55 degrees C for 30 seconds each using a PCR thermal cycler. After thermal cycling, specimens were subjected to microtensile bond strength test and fractured surfaces were observed by SEM. The bond strength of Imperva Fluoro Bond after 3000 times of thermal cycling was significantly decreased compared to those of less than 2000 cycles (p < 0.05), whereas SI-R20401 showed no significant differences even after 3000 cycles (p > 0.05). Results of this study revealed that bond strength was affected by the thermal stress introduced in this experimental model. Therefore, this new thermal cycling method is a potentially useful and accessible means to evaluate the durability of dentin adhesive systems.

Effect of double-application of all-in-one adhesives on dentin bonding.

OBJECTIVES: To evaluate the effect of double-application of all-in-one adhesives using the micro-shear bond test. METHODS: The occlusal surfaces of extracted human third molars were ground perpendicular to the long axis of each tooth to expose a flat dentin surface. Three commercially available and one experimental bonding system were used in this study: Adper Prompt L-Pop (APL, 3M ESPE), REACTMER BOND (RB, Shofu), XENO III (Xeno, Dentsply-Sankin) and newly developed OBF-2 (OB2, Tokuyama Dental). These adhesives were applied on the dentin surfaces by either the manufacturers' instructions or by an experimental method (single-application or double-application). Resin composite was then placed and light-cured for 40s. After 24h immersion in water, a micro-shear bond test was carried out and the fractured dentin surfaces were observed microscopically. The data were analyzed by one-way ANOVA and Tukey's HSD tests (p<0.05). RESULTS: The mean bond strengths of APL, RB, Xeno and OB2 with single-application were 22.7, 28.3, 30.3 and 34.6MPa, respectively. The mean bond strengths of APL, RB, Xeno and OB2 with double-application were 29.5, 27.2, 29.6 and 32.5MPa, respectively. There were no statistically significant differences in micro-shear bond strengths between the single- and double-application methods for each adhesive system (p>0.05). The morphological observation of the fractured dentin surfaces revealed differences between the single- and double-application groups especially for APL and OB2. CONCLUSIONS: Micro-shear bond strengths of all-in-one adhesives in this study showed no statistically significant differences between the single-application and the double-application method.

Micro-shear bond strength of five single-step adhesives to dentin.

The micro-shear bond strengths (MSBSs) of five single-step self-etch adhesives (Adper Prompt L-Pop [APL], AQ Bond plus [AQP], OBF-2 [OB2], Reactmer Bond [RB], and Xeno III [XIII]) were compared with that of a two-step self-etch adhesive, Clearfil SE Bond [SE]. The adhesives were applied on dentin surfaces, according to manufacturers' instructions, for bonding of resin composite to dentin. After 24 hours, a micro-shear bond test was carried out and the data were analyzed by one-way ANOVA and Bonferroni test (p<0.05). The mean MSBSs in MPa were APL: 22.8, AQP: 37.4, OB2: 34.7, RB: 28.3, XIII: 30.3, and SE: 47.2. Among the single-step adhesives, the MSBS of AQP and OB2 were significantly higher than APL (p<0.05). In conclusion, the single-step adhesives used in this study, apart from AQP, produced significantly lower MSBS than the two-step adhesive (p<0.05).