Effect of Time and Method of Drying on Bond Strength of Tray Adhesives with Vinyl Polysiloxanes.

AIM: To establish an effective combination of drying time and drying method of the tray adhesive so that maximum bond strength can be achieved between impression tray and impression material. MATERIALS AND METHODS: Cylindrical specimens of auto-polymerizing resin and addition silicone impression material were made. A total of 150 specimens were tested. They were divided into two groups Dentsply and GC. Each group was further divided into five subgroups: • Drying with compressed air for half the time as recommended by the manufacturer • Drying with air blower for half the time as recommended by the manufacturer • Open air drying as recommended by the manufacturer • Open air drying for 15 minutes • Open air drying for 1 hour The samples were tested for tensile bond strength using the universal testing machine. The results were subjected to statistical analysis. RESULT: Open air drying as recommended by the manufacturer was better than drying with a blower or compressed air. There was no significant difference between open-air drying for 5 minutes and open-air drying for 15 minutes or 1 hour. CONCLUSION: Open air drying as recommended by the manufacturer, i.e. 5min, showed good bond strength and drying for more than 5mins does not significantly increase bond strength. CLINICAL SIGNIFICANCE: Tray adhesive should not be dried with compressed air or air blower. Tray adhesive should be applied and kept to dry according to the manufacturer's recommended time.

Prosthetic Rehabilitation of Cranial Deformity in Hyperostotic Convexity Meningioma.

Cranial defects lead to unesthetic appearance and are a constant source of apprehension to the patient. Meningioma with calvarial extension requires the excision of the involved bone for complete excision. Such total excision would leave behind a bony defect which would need reconstruction. Presurgical fabrication of acrylic flap helps in reconstruction of such cranial defect following complete excision in single stage, thereby decreasing the cost and morbidity of surgery. Further, it facilitates the reproduction of the contours, and the tissue bed is not exposed to the heat of polymerization or to the free monomer. The authors report a case of hyperostotic convexity meningioma in a middle-aged female where heat-cured acrylic resin alloplastic implant was prefabricated and used successfully.

Prosthodontic management of a patient with ectodermal dysplasia.

Ectodermal dysplasia is a rare congenital disease that affects the ectodermal structures. It is characterized by hypotrichosis, hypohidrosis and hypodontia. A 14-year-old boy with ectodermal dysplasia presenting with oligodontia and marked resorption of the maxillary and mandibular alveolar ridges is reported. Prosthetic rehabilitation in the form of a maxillary and mandibular partial denture was made with metal crowns on existing lower teeth to achieve appropriate vertical dimension. Significant improvement in speech, masticatory function and facial esthetics was achieved. Removable prosthodontics can provide an acceptable solution to esthetic, functional and psychological rehabilitation in patients with ectodermal dysplasia.

Comparison of dimensional accuracy of four different die materials before and after disinfection of the impression: an in vitro study.

BACKGROUND: This study was conducted to compare the linear dimensional accuracy of die materials before and after disinfection of the impression. Type IV and V conventional dental stone, type IV-resin impregnated and copper-plated die materials were studied. MATERIALS AND METHODS: A stainless-steel master die analogs to a complete veneer crown preparation with three scribed lines (I: vertical, II and III: horizontal) was machined and measurements were made from these scribed reference lines. Impressions were made with monophase addition silicone impression material for each of the specimens. 2% glutaraldehyde was used as a disinfectant. The fabricated dies were measured to the nearest 0.0001 mm. ANOVA and post hoc was carried out using Scheffe multiple comparison test at significance level of 0.05. RESULTS: Type IV resin-impregnated dental stone and copperplated dies approximated the dimensions of the master die. Type IV and V conventional dental stone dies showed greater variation in measurements. Statistically significant differences were observed for type IV resin-impregnated and copper-plated dies in dimension I and III. For dimension II no significant differences were found for dies fabricated from four die materials. A one-way analysis of variance indicated no statistical significant differences among the two groups of dies fabricated from disinfectant treated impressions and those fabricated from nondisinfectant treated impressions. CONCLUSION: Type IV resin-impregnated dental stone and copper-plated dies are dimensionally more accurate than type IV and V conventional dental stone die materials. No significant linear distortion in the dies fabricated from the disinfected impressions was observed.