Analysis of the environmental impact on a stream: is only tannery to blame?

The contribution of wastewater from a tannery industry to the pollution of a stream was investigated. The main parameters studied were biochemical oxygen demand, chemical oxygen demand, chromium, dissolved oxygen, fecal and total coliforms, nitrogen, oils and greases, pH, phosphorous, sulfides, suspended solids, turbidity, and volatile solids. Three sampling points were located: (1) at the discharge point of tannery wastewater, (2) 50 m upstream, and (3) 80 m downstream of discharge point. Also was investigated the pollution at the stream source.

Simultaneous determination of the textile dyes in industrial effluents by first-order derivative spectrophotometry.

A first-order derivative spectrophotometric method for the simultaneous determination of three textile dyes, Procion Yellow HE4R, Procion Red HE7B and Remazol Black 5 (RB5), has been developed. The effects of pH, heating and ionic strength of the solution on the absorption spectra of the dyes were investigated. The wavelengths selected for the measures of the derivative signals of HE4R (395 nm), HE7B (604 nm) and RB5 (659 nm) presented these coefficients of linear correlation: 0.9978, 0.9992 and 0.9999, and these detection limits: 0.180, 0.317 and 0.0233 mg L(-1), respectively. The reliability and reproducibility of the method were tested and showed recovery values of 95.7 to 109%. The proposed method was applied for the determination of dyes in binary and ternary mixtures of textile effluents and showed an estimate of the loss of dyes for the effluents between 6.67 and 28.9%.

Combined electrocoagulation and TiO(2) photoassisted treatment applied to wastewater effluents from pharmaceutical and cosmetic industries.

The treated wastewater consists of refractory materials and high organic content of hydrolyzed peptone residues from pharmaceutical factory. The combination of electrocoagulation (EC) followed by heterogeneous photocatalysis (TiO(2)) conditions was maximized. The EC: iron cathode/anode (12.50 cmx2.50 cmx0.10 cm), current density 763Am(-2), 90min and initial pH 6.0. As EC consequence, the majority of the dissolved organic and suspended material was removed (about 91% and 86% of the turbidity and chemical oxygen demand (COD), respectively). After EC, refractory residues still remained in the effluent. The subsequent photocatalysis: UV/TiO(2)/H(2)O(2) (mercury lamps), pH 3.0, 4h irradiation, 0.25gL(-1) TiO(2) and 10mmolL(-1) H(2)O(2) shows high levels of inorganic and organic compounds eliminations. The obtained COD values: 1753mgL(-1) for the sample from the factory, 160mgL(-1) after EC and 50mgL(-1) after EC/photocatalyzed effluents pointed out that the combined treatment stresses this water purification.

Square wave voltammetry in the determination of Ni2+ and Al3+ in biological sample.

In this contribution, the amounts of Ni (nickel) and Al (aluminum) in tilapias (Oreochromis niloticus) were determined using square wave voltammetry (SWV) with glassy carbon working microelectrode with a mercury thin film, platinum counter electrode, and Ag/AgCl reference electrode. Ni was studied through the formation of the dimethylglyoxime-Ni (Ni-DMG) complex, while Al was studied through the formation of the Alizarin R-Al complex. The detection limit found for Ni-DMG and Alizarin R-Al complexes were 1.70 x 10(-7) and 1.0 x 10(-8) mol L(-1), respectively. The voltammetric anodic curves for the Alizarin R-Al complex were recorded over the potential range from -0.8 to -0.05 V while the voltammetric cathodic curve for the Ni-DMG complex was recorded over the potential range from -0.7 to -1.2 V. These methods detected low concentrations of Ni and Al in biological samples efficiently.

The effect of operational parameters on electrocoagulation-flotation process followed by photocatalysis applied to the decontamination of water effluents from cellulose and paper factories.

Cellulose and paper pulp factories utilize a large amount of water generating several undesirable contaminants. The present work is a preliminary investigation that associates the electrocoagulation-flotation (EC) method followed by photocatalysis to treat such wastewater. For EC, the experiment with aluminium and iron electrodes showed similar efficiency. Iron electrodes (anode and cathode) were chosen. By applying 30min of EC/Fe(0), 153A m(-2) and pH 6.0, the COD values, UV-vis absorbance and turbidity underwent an intense decrease. For the subsequent UV photocatalysis (mercury lamps) TiO(2) was employed and the favourable operational conditions found were 0.25g L(-1) of the catalyst and solution pH 3.0. The addition of hydrogen peroxide (50mmol L(-1)) highly increased the photo-process performance. By employing the UV/TiO(2)/H(2)O(2) system, the COD reduction was 88% compared to pre-treated effluents and complete sample photobleaching was verified. The salt concentration on EC (iron electrodes) showed that the electrolysis duration can be reduced from 30 to 10min by the addition of 5.0g L(-1) of NaCl. The biodegradability index (BOD/COD) increased from 0.15 (pre-treated) to 0.48 (after EC) and to 0.89 (after EC/photocatalysis irradiated for 6h), showing that the employed sequence is very helpful to improve the water quality. This result was confirmed by biotoxicity tests performed with microcrustaceous Artemia salina.

Capacity of adsorption of Pb2+ and Ni2+ from aqueous solutions by chitosan produced from silkworm chrysalides in different degrees of deacetylation.

The binding capacities of chitin (CT) and chitosan (CS) produced from silkworm chrysalides were investigated aiming at their future application in the removal of Pb2+ and Ni2+ from wastewaters. CS with 75% deacetylation degree (DD) exhibited good binding performance for Pb(2+), but bad efficiency for Ni2+. The maximum binding capacity obtained from isotherms for CS-Pb was 141.10 mg g(-1) and 52.81 mg g(-1) for CS-Ni. The binding capacities for CT were 32.01 mg g(-1) for Pb2+ and 61.24 mg g(-1) for Ni2+. The authors attribute these behaviors to two main factors: (i) the large ionic size of Pb2+ and (ii) the steric hindrance due to CT acetyl groups. Metal binding onto CS was evaluated by the Freundlich and Langmuir isotherm models. The parameter values obtained from the isotherm analysis confirmed that Pb2+ and Ni2+ interact differently with CS and that various factors influence their adsorption. Thermogravimetric analysis (TGA) showed that the thermal behavior of CS with 75% deacetylation degree was in the same profile of standard CS; however, the binding of the metals onto its structure affects the curve profile.

Removal of methylene blue dye from an aqueous media using superabsorbent hydrogel supported on modified polysaccharide.

The removal of methylene blue (MB) in water with the superabsorbent hydrogel (SH) formed by modified gum arabic, polyacrylate, and polyacrylamide was investigated. The SH exhibited excellent performance in MB absorption. The maximum absorption capacity was 48 mg of the dye per g of SH, representing 98% of the MB removed. Experimental parameters were used as follows: pH 8, hydrogel mass 50 mg, and initial concentration of MB 50 mg L(-1). In a procedure with an individual solution of orange II, an opposite effect related to the MB was observed: the hydrogel only absorbed water, resulting in an orange II-richer solution. The orange II concentration in solution increased about 50 times (relative to the initial concentration). In another experiment using an aqueous mixture of orange II and MB, the SH absorbed the MB exclusively. Compared to the MB, the orange II is separated from water by SH selectivity-absorption through an inverse process. This effect was attributed to the formation of a ionic complex between the imine groups of MB and the ionized carboxylic groups of SH.

Novel adsorbent based on silkworm chrysalides for removal of heavy metals from wastewaters.

In this contribution, maximum capacity for adsorption of Pb(2+), Ni(2+), and Cu(2+) by silkworm chrysalides (SC) was determined. The raw silkworm chrysalides (SC(r)) and chrysalides after acidic washing (SC(w)) were used. Chitin (CT), extracted from SC, and chitosan (CS), with 85% deacetylation, were employed as reference samples. Adsorption tests showed that all the studied adsorbents exhibited excellent performance in removal of metals. The choice of a more appropriate adsorbent is related to its efficiency for removal of a specific metal. The studied materials presented different intensities for metal adsorption as follows: (i) Ni(2+)>Cu(2+)>Pb(2+) for SC(r); (ii) Pb(2+)>Cu(2+)>Ni(2+) for SC(w); (iii) Ni(2+)>Cu(2+)>Pb(2+) for CT; and (iv) Cu(2+)>Pb(2+)>Ni(2+) for CS. Metal adsorption onto SC(r) and CS was analyzed by Freundlich and Langmuir isotherm equations. Adsorption values for CS-Pb and SC(r)-Ni were provided by the Freundlich model, while the adsorption values for CS-Cu, CS-Ni, SC(r)-Pb, and SC(r)-Cu were provided by the Langmuir model. The studied adsorbents are suitable for use in treatment of wastewater. From the economic point of view, the use of SC(r) as an adsorbent of heavy metals (mainly Ni(2+)) on the large industrial scale would be more appropriate.

Spectrophotometric determination of Blue Procion HEGN in effluents of textile industry exploiting the dye aggregation effect and flow injection analysis.

A new spectrophotometric method involving flow injection analysis and textile dye aggregation effect is proposed. The method is based on the aggregation effect of Blue Procion HEGN at pH 3, which relocates its maximum absorption wavelength from 620 to 776 nm, avoiding the interference of other blue textile dyes. For this task, a simple and robust flow injection system was designed, which became a very stable analytical method. When the system was applied to Blue Procion determination in effluent of textile industry, precise results were observed (RSD < 2% within 1.0 and 5.0 mg l(-1) HEGN). The analytical frequency was 80 measurements per hour; the analytical curve was linear from 1.0 to 5.0 mg l(-1) HEGN; the detection limit considering three times the standard deviation of the blank solution (n = 10) was estimated as 0.03 mg l(-1) HEGN; and recoveries between 95% and 105% were found. The system consumes 20 mg of sodium citrate and 125 microl of the sample per determination. No baseline drift was observed during extended (5 h) operation periods.

Interpretation of seasonal variation of metals and abiotic properties in a tropical lake using multivariate analysis and MINTEQA2 program.

The hydrological cycle of Lake Ipê and the principal parameters that could affect its abiotic parameters and its metal (Fe, Mn, and Cd) concentrations were investigated. A detailed study of seasonal variations using Principal Components Analysis (PCA) for the most relevant metals (Fe, Mn and Cd) was performed, assisted by the MINTEQA2 geochemical equilibrium program using 15 water abiotic parameters. The abiotic variables and metals in the lake were governed by the hydrological regimen of the Parana River and by the occurrence of occasional flood pulses and rainfall. The occurrence of cadmium is a concern; its presence could be due to industrial or agricultural activities or even to a natural geochemical process.

Comparison of metal analysis in sediments using EDXRF and ICP-OES with the HCl and Tessie extraction methods.

The work presents an investigation on metal availability in sediments during 13 months using the dispersive-energy X-ray fluorescence (EDXRF) and atomic emission spectrometry with induced argon plasma (ICP-OES) techniques and single extraction (0.1moll(-1) HCl) and Tessie's sequential speciation methods. The EDXRF technique could yield essentially the same profile as ICP-OES for the seasonal variation of metals in sediments, but in a more practical way. The sequential extraction procedure (SEP) was more efficient in metal dissolution than single extraction. The Pb, Ni, Al, Cr, and Fe elements were less efficiently extracted with single extraction in relation to sequential extraction. For Co both methodologies were equivalent, but for Cu and Mn the extraction was higher with single extraction. Single extraction does not mobilize Pb, Ni, Al, Cr, and Fe adsorbed on oxides and bound to organic matter. However for Cu and Mn, not only extracted these metals from the four fractions, but it also dissolved part of the fifth fraction (residual). Principal Component Analysis discriminated seasonal variations in the content of several metals, mainly Fe, Co, Ni, and Zn. The mobility of metallic ions in the sediments is conditioned to the seasonal flow of organic and inorganic material coming from the river or by the erosion of adjacent soils.