The Effect of Viscous Drag on the Maximum Residual Stresses Achievable in High-Yield-Strength Materials in Laser Shock Processing.

In this paper, the experimentally observed significant increase in yield stress for strain rates beyond 104 s-1 (viscous regime) is explicitly considered in laser shock processing (LSP) simulations. First, a detailed review of the most common high-strain-rate deformation models is presented, highlighting the expected strain rates in materials subject to LSP for a wide range of treatment conditions. Second, the abrupt yield stress increase presented beyond 104 s-1 is explicitly considered in the material model of a titanium alloy subject to LSP. A combined numerical-analytical approach is used to predict the time evolution of the plastic strain. Finally, extended areas are irradiated covering a squared area of 25 × 25 mm2 for numerical-experimental validation. The in-depth experimental residual stress profiles are obtained by means of the hole drilling method. Near-surface-temperature gradients are explicitly considered in simulations. In summary, the conventionally accepted strain rate range in LSP (106-107 s-1) is challenged in this paper. Results show that the conventional high-strain-rate hardening models widely used in LSP simulations (i.e., Johnson Cook model) clearly overestimate the induced compressive residual stresses. Additionally, pressure decay, whose importance is usually neglected, has been found to play a significant role in the total plastic strain achieved by LSP treatments.

Morphological Analysis of Laser Surface Texturing Effect on AISI 430 Stainless Steel.

Laser surface texturing (LST) is a method to obtain micro-structures on the material's surface for improving tribological performances, wetting tuning, surface treatment, and increasing adhesion. The material selected for LST is AISI 430 ferritic stainless steel, distinguished by the low cost in manufacturing, corrosion resistance, and high strength at elevated temperature. The present study addresses the morphology of new pattern designs (crater array, ellipse, and octagonal shapes). The patterns are applied on the stainless-steel surface by a non-contact method with high quality and precision nanosecond pulsed laser equipment. The investigation of laser parameter influence on thermal affected area and micro-structures is accomplished by morphological and elemental analysis (SEM + EDX). The parameters of the laser micro-patterning have a marked influence on the morphology, creating groove-type sections with different depths and recast material features. From the SEM characterization, the highest level of recast material is observed for concentric octagon LST design. Its application is more recommended for the preparation of the metal surface before hybrid welding. Additionally, the lack of the oxygen element in the case of this design suggests the possible use of the pattern in hybrid joining.

Wettability and Surface Roughness Analysis of Laser Surface Texturing of AISI 430 Stainless Steel.

Due to its wide applicability in industry, devising microstructures on the surface of materials can be easily implemented and automated in technological processes. Laser Surface Texturing (LST) is applied to modify the chemical composition, morphology, and roughness of surfaces (wettability), cleaning (remove contaminants), reducing internal stresses of metals (hardening, tempering), surface energy (polymers, metals), increasing the adhesion (hybrid joining, bioengineering) and decreasing the growth of pathogenic bacteria (bioengineering). This paper is a continuation and extension of our previous studies in laser-assisted texturing of surfaces. Three different patterns (crater array-type C, two ellipses at 90° overlapping with its mirror-type B and 3 concentric octagons-type A) were applied with a nanosecond pulsed laser (active medium Nd: Fiber Diode-pumped) on the surface of a ferritic stainless steel (AISI 430). Micro texturing the surface of a material can modify its wettability behavior. A hydrophobic surface (contact angle greater than 90°) was obtained with different variations depending on the parameters. The analysis performed in this research (surface roughness, wettability) is critical for assessing the surface functionality, characteristics and properties of the stainless steel surface after the LST process. The values of the surface roughness and the contact angle are directly proportional to the number of repetitions and inversely proportional to the speed. Recommendations for the use of different texturing pattern designs are also made.

Direct Generation of High-Aspect-Ratio Structures of AISI 316L by Laser-Assisted Powder Deposition.

The effect of process parameters and the orientation of the cladding layer on the mechanical properties of 316L stainless steel components manufactured by laser metal deposition (LMD) was investigated. High aspect-ratio walls were manufactured with layers of a 4.5 mm wide single-cladding track to study the microstructure and mechanical properties along the length and the height of the wall. Samples for the tensile test (according to ASTM E-8M-04) were machined from the wall along both the direction of the layers and the direction perpendicular to them. Cross-sections of the LMD samples were analyzed by optical and scanning electron microscopy (SEM). The orientation of the growing grain was observed. It was associated with the thermal gradient through the building part. A homogeneous microstructure between consecutive layers and some degree of microporosity was observed by SEM. Uniaxial tension tests were performed on samples extracted from the wall in perpendicular and parallel directions. Results for ultimate tensile strength were similar in both cases and with the wrought material. The σ0.2 were similar in both cases but slightly superior to the wrought material.