Quantifying thermal transport in buried semiconductor nanostructures via cross-sectional scanning thermal microscopy.

Managing thermal transport in nanostructures became a major challenge in the development of active microelectronic, optoelectronic and thermoelectric devices, stalling the famous Moore's law of clock speed increase of microprocessors for more than a decade. To find the solution to this and linked problems, one needs to quantify the ability of these nanostructures to conduct heat with adequate precision, nanoscale resolution, and, essentially, for the internal layers buried in the 3D structure of modern semiconductor devices. Existing thermoreflectance measurements and "hot wire" 3ω methods cannot be effectively used at lateral dimensions of a layer below a micrometre; moreover, they are sensitive mainly to the surface layers of a relatively high thickness of above 100 nm. Scanning thermal microscopy (SThM), while providing the required lateral resolution, provides mainly qualitative data of the layer conductance due to undefined tip-surface and interlayer contact resistances. In this study, we used cross-sectional SThM (xSThM), a new method combining scanning probe microscopy compatible Ar-ion beam exit nano-cross-sectioning (BEXP) and SThM, to quantify thermal conductance in complex multilayer nanostructures and to measure local thermal conductivity of oxide and semiconductor materials, such as SiO2, SiGex and GeSny. By using the new method that provides 10 nm thickness and few tens of nm lateral resolution, we pinpoint crystalline defects in SiGe/GeSn optoelectronic materials by measuring nanoscale thermal transport and quantifying thermal conductivity and interfacial thermal resistance in thin spin-on materials used in extreme ultraviolet lithography (eUV) fabrication processing. The new capability of xSThM demonstrated here for the first time is poised to provide vital insights into thermal transport in advanced nanoscale materials and devices.

Weak localization and weak antilocalization in doped Ge1-y Sn y layers with up to 8% Sn.

Low-temperature magnetoresistance measurements of n- and p-doped germanium-tin (Ge1-y Sn y ) layers with Sn concentrations up to 8% show contributions arising from effects of weak localization for n-type and weak antilocalization for p-type doped samples independent of the Sn concentration. Calculations of the magnetoresistance using the Hikami-Larkin-Nagaoka model for two-dimensional transport allow us to extract the phase-coherence length for all samples as well as the spin-orbit length for the p-type doped samples. For pure Ge, we find phase-coherence lengths as long as (349.0 ± 1.4) nm and (614.0 ± 0.9) nm for n-type and p-type doped samples, respectively. The phase-coherence length decreases with increasing Sn concentration. From the spin-orbit scattering length, we determine the spin-diffusion scattering length in the range of 20-30 nm for all highly degenerate p-type doped samples irrespective of Sn concentration. These results show that Ge1-y Sn y is a promising material for future spintronic applications.

Electrical detection of spin transport in Si two-dimensional electron gas systems.

Spin transport in a semiconductor-based two-dimensional electron gas (2DEG) system has been attractive in spintronics for more than ten years. The inherent advantages of high-mobility channel and enhanced spin-orbital interaction promise a long spin diffusion length and efficient spin manipulation, which are essential for the application of spintronics devices. However, the difficulty of making high-quality ferromagnetic (FM) contacts to the buried 2DEG channel in the heterostructure systems limits the potential developments in functional devices. In this paper, we experimentally demonstrate electrical detection of spin transport in a high-mobility 2DEG system using FM Mn-germanosilicide (Mn(Si0.7Ge0.3)x) end contacts, which is the first report of spin injection and detection in a 2DEG confined in a Si/SiGe modulation doped quantum well structure (MODQW). The extracted spin diffusion length and lifetime are l sf = 4.5 µm and [Formula: see text] at 1.9 K respectively. Our results provide a promising approach for spin injection into 2DEG system in the Si-based MODQW, which may lead to innovative spintronic applications such as spin-based transistor, logic, and memory devices.

Electroluminescence of GeSn/Ge MQW LEDs on Si substrate.

Multi-quantum well light-emitting diodes, consisting of ten alternating GeSn/Ge-layers, were grown by molecular beam epitaxy on Si. The Ge barriers were 10 nm thick, and the GeSn wells were grown with 7% Sn and thicknesses between 6 and 12 nm. The electroluminescence spectra measured at 300 and 80 K yield a broad and intensive luminescence band. Deconvolution revealed three major lines produced by the GeSn wells that can be interpreted in terms of quantum confinement. We interpret that the three lines represent two direct lines, formed by transitions with the light and heavy hole band, respectively, and an indirect line. Biaxial compressive strain causes a splitting of light and heavy holes in the GeSn wells. This interpretation is supported by an effective mass band structure calculation.

Electrically pumped lasing from Ge Fabry-Perot resonators on Si.

Room temperature lasing from electrically pumped n-type doped Ge edge emitting devices has been observed. The edge emitter is formed by cleaving Si-Ge waveguide heterodiodes, providing optical feedback through a Fabry-Perot resonator. The electroluminescence spectra of the devices showed optical bleaching and intensity gain for wavelengths between 1660 nm and 1700 nm. This fits the theoretically predicted behavior for the n-type Ge material system. With further pulsed electrical injection of 500 kA/cm2 it was possible to reach the lasing threshold for such edge emitters. Different lengths and widths of devices have been investigated in order to maintain best gain-absorption ratios.

GeSn-on-Si normal incidence photodetectors with bandwidths more than 40 GHz.

GeSn (Sn content up to 4.2%) photodiodes with vertical pin structures were grown on thin Ge virtual substrates on Si by a low temperature (160 °C) molecular beam epitaxy. Vertical detectors were fabricated by a double mesa process with mesa radii between 5 µm and 80 µm. The nominal intrinsic absorber contains carrier densities from below 1 · 10(16) cm(-3) to 1 · 10(17) cm(-3) for Ge reference detectors and GeSn detectors with 4.2% Sn, respectively. The photodetectors were investigated with electrical and optoelectrical methods from direct current up to high frequencies (40 GHz). For a laser wavelength of 1550 nm an increasing of the optical responsivities (84 mA/W -218 mA/W) for vertical incidence detectors with thin (300 nm) absorbers as function of the Sn content were found. Most important from an application perspective all detectors had bandwidth above 40 GHz at enough reverse voltage which increased from zero to -5 V within the given Sn range. Increasing carrier densities (up to 1 · 10(17) cm(-3)) with Sn contents caused the depletion of the nominal intrinsic absorber at increasing reverse voltages.

Direct bandgap narrowing in Ge LED's on Si substrates.

In this paper we investigate the influence of n-type doping in Ge light emitting diodes on Si substrates on the room temperature emission spectrum. The layer structures are grown with a special low temperature molecular beam epitaxy process resulting in a slight tensile strain of 0.13%. The Ge LED's show a dominant direct bandgap emission with shrinking bandgap at the Γ point in dependence of n-type doping level. The emission shift (38 meV at 10²°cm⁻³) is mainly assigned to bandgap narrowing at high doping. The electroluminescence intensity increases with doping concentrations up to 3x10¹9cm⁻³ and decreases sharply at higher doping levels. The integrated direct gap emission intensity increases superlinear with electrical current density. Power exponents vary from about 2 at low doping densities up to 3.6 at 10²°cm⁻³ doping density.

Development of a comprehensive analytical method for the determination of chlorinated paraffins in spruce needles applied in passive air sampling.

Conifer needles are used for the monitoring of atmospheric persistent organic pollutants. The objective of the present study was to develop a method for the detection of airborne chlorinated paraffins (CPs) using spruce needles as a passive sampler. The method is based on liquid extraction of the cuticular wax layer followed by chromatographic fractionation and detection of CPs using two different GCMS techniques. Total CP concentrations (sum of short (SCCP), medium (MCCP) and long chain CPs (LCCP)) were determined by EI-MS/MS. SCCP and MCCP levels as well as congener group patterns (n-alkane chain length, chlorine content) could be evaluated using ECNI-LRMS. For the first time, data on environmental airborne CPs on spruce needles taken within the Monitoring Network in the Alpine Region for Persistent and other Organic Pollutants (MONARPOP) are presented providing evidence that spruce needles are a suitable passive sampling system for the monitoring of atmospheric CPs.

Altitude profiles of total chlorinated paraffins in humus and spruce needles from the Alps (MONARPOP).

Chlorinated paraffins (CPs) are toxic, bioaccumulative, persistent, and ubiquitously present in the environment. CPs were analyzed in humus and needle samples, which were taken within the Monitoring Network in the Alpine Region for Persistent and other Organic Pollutants (MONARPOP) at sampling sites of 7 different altitude profiles in the Alps. Gas chromatography combined with electron ionization tandem mass spectrometry (EI-MS/MS) was used for the determination of total CPs (sum of short, medium and long chain CPs). CPs were found in all samples; the concentrations varied between 7 and 199 ng g(-1) dry weight (dw) and within 26 and 460 ng g(-1) dw in humus and needle samples, respectively. A clear vertical tendency within the individual altitude profiles could not be ascertained. Within all altitude profiles, elevated concentrations were observed in humus samples taken between 700 and 900 m and between 1300 and 1500 m. In the needle samples no similar correlation could be observed due to higher variation of the data.

Historical profiles of chlorinated paraffins and polychlorinated biphenyls in a dated sediment core from Lake Thun (Switzerland).

A dated sediment core from Lake Thun covering the last 120 years was analyzed to get an overview of the historical trend of the chlorinated paraffin (CP) and polychlorinated biphenyl (PCB) deposition, because CPs and PCBs have/had similar applications as plasticizers and flame retardants. Total CP concentrations (sum of short chain (SCCP), medium chain (MCCP), and long chain CPs (LCCP)) showed a steep increase in the 1980s and a more-or-less stable level of 50 ng g(-1) dry weight (dw) since then. The concentration-time profile is in good agreement with the available information on global production data. The quantification of higher chlorinated SCCPs using electron capture negative ionization low resolution mass spectrometry (ECNI-LRMS) revealed an increase in recent years. In addition, the degree of chlorination of SCCPs has strongly increased during the past 40 years, which may indicate its use as an additive for plastics, paints, and coatings. Furthermore, PCBs were analyzed in dated sediment slices. The PCB concentrations (sum of the six indicator congeners) peaked around 1969 (18 ng g(-1) dw) and decreased to 1.3 ng g(-1) dw in the surface layer corresponding to 2004. The peak level of CPs exceeded those of PCBs by about a factor of 3.

Mass spectral studies of perfluorooctane sulfonate derivatives separated by high-resolution gas chromatography.

The mass spectral characteristics of perfluorooctane sulfonate (PFOS, C(8)F(17)SO(3)-) isomers present in technical PFOS were obtained using high-resolution gas chromatography (HRGC) combined with mass spectrometry (MS). To make PFOS amenable to HRGC separation, a simple derivatization procedure was developed. The method involved the conversion of PFOS into the iso-propyl ester using iso-propanol as the derivatization reagent under acidic conditions. Mass spectra were generated employing electron ionization (EI) and negative chemical ionization (NCI). Interpretation of fragment ions was possible due to the use of deuterium-labeled iso-propanol as derivatization reagent, which induced mass shifts in the electron ionization (EI) and negative chemical ionization (NCI) mass spectra. HRMS allowed the accurate mass measurement of important EI fragments and confirmed the derivatization reaction as well as the proposed fragmentation pathway involving rearrangement. Moreover, the high resolution provided by HRGC enabled the separation of eleven PFOS isomers present in the technical product. This is an improvement over the previously reported high-performance liquid chromatography (HPLC) separation. A complete identification of all isomers was not possible due to lack of pure reference materials. Finally, the developed derivatization procedure was successfully applied to perfluoroalkyl carboxylates (PFCA) and corresponding fragmentation involving rearrangement of the derivatized PFCA was observed. The described qualitative derivatization offers a promising alternative technique for the separation and identification of isomers of perfluoroalkyl sulfonates and carboxylates by HRGC/MS.

Peak splitting in the CE separation of enantiomers caused by organic solvents in the sample.

Two robust chiral standard separation systems were developed for the analysis of the chiral purity of chemically different model compounds applied in homogeneous asymmetric hydrogenation catalysis. Sulfated CDs were used as chiral selectors as they allow the analysis of neutral, acidic as well as basic compounds in the same electrophoretic system. Poorly water-soluble amines were dissolved in different organic solvent/buffer mixtures. Reproducibly, depending on the amount of organic solvent in the sample solution, peak splitting occurred and/or more peaks than expected were observed, implying impure model compounds. The dependence of the "chiral purity" on experimental parameters, e.g., kind and amount of sample solvent, length of injection plug, inner surface modification of the capillary, kind of sulfated CD, hydrophobicity, and basicity of the analytes, etc. was investigated. It is gathered that different equilibrium constants of the strong binding basic analytes and highly sulfated CD complex in the organic phase of the injection plug and the aqueous electrolyte phase are resulting in two different mobility zones for each enantiomer. It follows that each enantiomer is showing two peaks instead of one. Experimental strategies are shown to avoid these peak splitting/artificial impurity effects and obtain the "real" chiral purity picture of the samples.

Organic pollutants in compost and digestate. Part 2. Polychlorinated dibenzo-p-dioxins, and -furans, dioxin-like polychlorinated biphenyls, brominated flame retardants, perfluorinated alkyl substances, pesticides, and other compounds.

Compost and digestate are important recycling fertilizers and have beneficial effects on soil parameters. However, they can contain significant amounts of organic pollutants. Here, the first comprehensive data set on dibenzo-p-dioxins and -furans (PCDD/F), dioxin-like polychlorinated biphenyls (DL-PCB), brominated flame retardants, perfluorinated alkyl substances (PFAS), pesticides, phthalates, nonylphenol and chlorinated paraffins (CP) in source-separated compost and digestate from Switzerland is presented (n = 3-18). The median summation 17PCDD/F and summation 12DL-PCB concentrations were at 3.2 ng I-TEQ kg(-1)dry weight (dw) and 3.0 ng WHO-TEQ kg(-1)dw, respectively. Brominated diphenyl ether 209 (BDE 209) accounted for 72% of the total polyBDE content (10 microg kg(-1)dw). Hexabromocyclododecane (HBCD) and tetrabromobisphenol A (TBBPA) levels were at 100 and 0.51 microg kg(-1)dw, respectively. PFAS were identified for the first time in compost and digestate (median concentration 6.3 microg kg(-1)dw, summation 21compounds). Out of 269 pesticides analysed, 30 fungicides, 14 herbicides, eight insecticides and one acaricide were detected. Di-(2-ethylhexyl)phthalate (DEHP) median concentration accounted for 280 microg kg(-1)dw and nonylphenol was below the detection limit of 1 mg kg(-1)dw. The sum of short and medium chain CP was between 90 and 390 microg kg(-1)dw. The concentrations observed were at or above the levels found in background soils, which are the main recipient of compost and digestate. Where actually applied, compost can contribute considerably to the total input of organic pollutants to the soil. However, on a total Swiss agricultural area base, inputs seem to be limited.

Identification and pattern of perfluorooctane sulfonate (PFOS) isomers in human serum and plasma.

Human serum and plasma from Sweden (n=17), the United Kingdom (the UK) (n=13) and Australia (n=40) were analyzed by high performance liquid chromatography coupled to mass spectrometry. The objective was to identify different perfluorooctane sulfonate (PFOS) isomers. Similar isomer patterns typical for the electrochemical fluorination (ECF) process were found for all samples. The linear PFOS (L-PFOS) was the major isomer found (58-70%) followed by the monosubstituted PFOS isomers 1/6-CF(3)-PFOS (18-22%) and 3/4/5-CF(3)-PFOS (13-18%). Disubstituted isomers were also detected. The percentage of L-PFOS found in the serum and plasma samples was lower compared to a standard PFOS product (76-79%). The pattern of PFOS isomers in human serum and plasma may be suggestive concerning potential isomeric discrimination since PFOS is only produced by ECF. Possibilities for such isomer discrimination are discussed. Significant higher content of L-PFOS (68%) in Swedish samples compared to Australia and the UK (59%) was also found, which may suggest differences in exposure sources for humans.

Short- and medium-chain chlorinated paraffins in biota from the European Arctic -- differences in homologue group patterns.

Congener and homologue group patterns of chlorinated paraffins (CPs) in biota can be influenced by different processes, but these are not well studied yet. Short- (SCCPs) and medium-chain chlorinated paraffins (MCCPs) were quantified in liver from Arctic char and seabirds (little auk and kittiwake) collected at Bear Island (European Arctic) as well as in cod from Iceland and Norway. CP concentrations were between 5 and 88 ng/g wet weight (ww) for SCCPs and between 5 and 55 ng/g ww for MCCPs with one exception of 370 ng/g measured in a liver sample from little auk. The SCCP homologue group patterns were compared with those of technical mixtures and of SCCPs present in cod liver from the Baltic Sea. The latter showed a more common SCCP homologue distribution (sum of C(11) and C(12)>60%) in contrast to cod liver from the Northwest of Europe, which had a high abundance of C(10) and C(12) congeners. Seabirds from Bear Island contained an equally distributed SCCP homologue group pattern. In Arctic char, the SCCP distribution was closer to technical products, but with a high proportion (average of 18.9%) of C(10) congeners. A comparison of C(10)/C(12) ratios confirmed the higher abundance of C(10) congeners in samples from higher latitudes. For the first time, MCCPs could be detected in Arctic samples. The average proportion of C(14) congeners was 65.8%. The C(14)/C(15) abundance ratio was similar to technical mixtures. High-chlorinated CPs (Cl(>7)) were also detectable. The average chlorine content of the SCCPs was 61.9% (59.0-63.3%), and that of the MCCPs 55.8% (54.5-57.4%).

Structural identification of isomers present in technical perfluorooctane sulfonate by tandem mass spectrometry.

The structures of isomeric by-products of technical perfluorooctane sulfonate (PFOS, C8F17SO3-) were characterized by high-performance liquid chromatography coupled to mass spectrometry. Ion trap (IT) as well as triple quadrupole (TQ) tandem mass spectrometry (MS/MS) identified ten PFOS isomers with best results being achieved by ion trap MS/MS. In addition to the linear isomer, the main by-products were isomers with geminal diperfluoromethyl groups and perfluoromethyl-substituted compounds. Purified fractions of the perfluoromethyl isomers allowed the elucidation of structures and the assignment of the retention times of perfluoroisopropyl-, 5-perfluoromethyl-, 4-perfluoromethyl-, 3-perfluoromethyl- and 1-perfluoromethyl-PFOS. The concentration of 2-perfluoromethyl-PFOS was too low in technical PFOS for a proper identification. Retention times of the geminal substituted diperfluoromethyl isomers could not be properly assigned due to co-elutions. The number and position of the CF3 groups can be derived from the MS/MS spectra, which allow an unequivocal identification of the isomers. TQ-MS/MS also allowed us to identify most of the isomers.

Congener group patterns of chloroparaffins in marine sediments obtained by chloride attachment chemical ionization and electron capture negative ionization.

Congener group patterns of technical short chain and medium chain chloroparaffins (SCCP and MCCP) were determined by electron capture negative ionization (ECNI) and chloride attachment chemical ionization (CACI) mass spectrometry (MS). In contrast to CACI-MS, congener patterns obtained by ECNI showed always a shift to the next higher chlorinated congener and carbon chain length group. Consequently, the calculated molecular masses and chlorine contents were higher for ECNI (factor 1.10+/-0.03 and 1.09+/-0.03, respectively). ECNI/CACI ratios in sediment samples from the North and Baltic Sea were also slightly higher. However, a more pronounced shift of the congener pattern for a given carbon chain length to congeners with 2-3 more chlorine atoms was observed. SCCP and MCCP concentrations obtained by ECNI-MS were in the range of 8-63ngg(-1) (North Sea) and 22-149ngg(-1) dry weight (Baltic Sea). MCCP levels were highest in all samples (MCCP/SCCP factor 1.1-3.2).

Presence of chlorinated paraffins in sediments from the North and Baltic Seas.

Chloroparaffins (CPs) were determined in sediments collected from the North and Baltic Seas during monitoring campaigns in 2001-2003. Electron ionization tandem mass spectrometry (MS/MS) was used for a first screening. It allowed the simultaneous determination of short (SCCP) and medium chain chlorinated paraffins (MCCP). SCCP+MCCP concentrations between 5 and 499 ng/g dry weight were found. In general, Baltic Sea sediments were more highly contaminated by CPs than the North Sea was. However, concentrations related to the total organic carbon content were on the same order of magnitude due to the higher organic content in the Baltic Sea. Additional information about the congener and homologue pattern was obtained for selected samples from the Baltic Sea by high-resolution gas chromatography combined with negative ion chemical ionization and low-resolution mass spectrometry, Concentrations in the North Sea were in general too low for this approach. In the Baltic Sea, MCCP concentrations were 1.7-2.4 times higher than for SCCPs. Lower chlorinated C(13) and C(14) compounds were the main CP compounds. The CP congener and homologue patterns showed similarities with technical SCCP and MCCP mixtures when compared using principal component analysis.