Simple Approach to Enhance Long-Term Environmental Stability of MXene Using Initiated Chemical Vapor Deposition Surface Coating.

Developing a methodology to enhance long-term stability is one of the most important issues in MXene research, since they are prone to oxidation in the ambient environment. Although various approaches have been suggested to improve the stability of MXene, they have suffered from complicated processes and limited applicability to various types of MXene nanostructures. Herein, we report a simple and versatile technique to enhance the environmental stability of MXenes. Ti3C2Tx MXene films were decorated with a highly hydrophobic polymer, 1H,1H,2H,2H-perfluorodecyl methacrylate (PFDMA), using initiated chemical vapor deposition (iCVD) where iCVD allows the facile postdeposition of polymer films of desired thickness on MXene films. The oxidation resistance was evaluated by fabricating MXene gas sensors and measuring the change in signal-to-noise ratio (SNR) of volatile organic compound (VOC) gases under harsh conditions (RH 100% at 50 °C) for several weeks where the performance in the absence and presence of PFDMA was compared. The results show that while the SNR of PFDMA-Ti3C2Tx sensors was retained, a dramatic increase of the noise level and a decrease in the SNR were observed in pristine Ti3C2Tx. We believe that this simple and nondestructive method will offer great potential to enhance the stability of a wide range of MXenes.

Microfluidic formation of surface nanodroplets using green deep eutectic solvents for liquid-liquid nanoextraction and controlled precipitation.

HYPOTHESIS: Surface nanodroplets have recently been employed for in situ chemical analysis leveraging their low volume, e.g. O(10-15 L), that enables rapid analyte extraction and pre-concentration. So far, most surface nanodroplets have been formed using single organic solvents such as 1-octanol, toluene, among others. Designing multicomponent surface nanodroplet with controllable composition is highly desirable for extending their application as extractant. EXPERIMENT: Here, we formed surface nanodroplets using green deep eutectic solvent (gDES) composed of thymol and decanoic acid, both of which are naturally occurring chemicals. The influence of parameters such as flowrate and the composition of deep eutectic solvent on the surface nanodroplet formation were studied. As proof-of-concept, the gDES surface nanodroplets were further used to extract and detect trace amounts of fluorescent rhodamine 6G dye and copper ions from water. FINDINGS: The formation of gDES surface nanodroplets follows the theoretical model which states that the final droplet volume (Vf) scales with the Peclét number (Pe) of the flow during formation by the solvent exchange process, that is Vf âˆ¼ Pe3/4, and the nanodroplets demonstrate excellent ability as extractant for rhodamine 6G and copper ions from water. Surprisingly, the confined volume of gDES surface nanodroplets enables fast and controlled formation of Cu (II)-decanoate crystal.

Springtail-inspired superomniphobic surface with extreme pressure resistance.

Both high static repellency and pressure resistance are critical to achieving a high-performance omniphobic surface. The cuticles of springtails have both of these features, which result from their hierarchical structure composed of primary doubly reentrant nanostructures on secondary microgrooves. Despite intensive efforts, none of the previous studies that were inspired by the springtail were able to simultaneously achieve both high static repellency and pressure resistance because of a general trade-off between these characteristics. We demonstrate for the first time a springtail-inspired superomniphobic surface displaying both features by fabricating a hierarchical system consisting of serif-T-shaped nanostructures on microscale wrinkles, overcoming previous limitations. Our biomimetic strategy yielded a surface showing high repellency to diverse liquids, from water to ethanol, with a contact angle above 150°. Simultaneously, the surface was able to endure extreme pressure resulting from the impacts of drops of water and of ethylene glycol with We >> 200, and of ethanol with We ~ 53, which is the highest pressure resistance ever reported. Overall, the omniphobicity of our springtail-inspired fabricated system was found to be superior to that of the natural springtail cuticle itself.

Robust Thin Film Surface with a Selective Antibacterial Property Enabled via a Cross-Linked Ionic Polymer Coating for Infection-Resistant Medical Applications.

Fabrication of new antibacterial surfaces has become a primary strategy for preventing device-associated infections (DAIs). Although considerable progress has recently been made in reducing DAIs, current antibacterial coating methods are technically complex and do not allow selective bacterial killing. Here, we propose novel anti-infective surfaces made of a cross-linked ionic polymer film that achieve selective bacteria killing while simultaneously favoring the survival of mammalian cells. A one-step polymerization process known as initiated chemical vapor deposition was used to generate a cross-linked ionic polymer film from 4-vinylbenzyl chloride and 2-(dimethylamino) ethyl methacrylate monomers in the vapor phase. In particular, the deposition process produced a polymer network with quaternary ammonium cross-linking sites, which provided the surface with an ionic moiety with an excellent antibacterial contact-killing property. This method confers substrate compatibility, which enables various materials to be coated with ionic polymer films for use in medical implants. Moreover, the ionic polymer-deposited surfaces supported the healthy growth of mammalian cells while selectively inhibiting bacterial growth in coculture models without any detectable cytotoxicity. Thus, the cross-linked ionic polymer-based antibacterial surface developed in this study can serve as an ideal platform for biomedical applications that require a highly sterile environment.

One-Step Synthesis of Cross-Linked Ionic Polymer Thin Films in Vapor Phase and Its Application to an Oil/Water Separation Membrane.

In spite of the huge research interest, ionic polymers could not have been synthesized in the vapor phase because the monomers of ionic polymers contain nonvolatile ionic salts, preventing the monomers from vaporization. Here, we suggest a new, one-step synthetic pathway to form a series of cross-linked ionic polymers (CIPs) in the vapor phase via initiated chemical vapor deposition (iCVD). 2-(Dimethylamino)ethyl methacrylate (DMAEMA) and 4-vinylbenzyl chloride (VBC) monomers are introduced into the iCVD reactor in the vapor phase to form a copolymer film. Simultaneously in the course of the deposition process, the tertiary amine in DMAEMA and benzylic chloride in VBC undergo a Menshutkin nucleophilic substitution reaction to form an ionic ammonium-chloride complex, forming a highly cross-linked ionic copolymer film of p(DMAEMA-co-VBC). To the best of our knowledge, this is the first report on the synthesis of CIP films in the vapor phase. The newly developed CIP thin film is further applied to the surface modification of the membrane for oil/water separation. With the hydrophilic and underwater oleophobic membrane whose surface is modified with the CIP film, excellent separation efficiency (>99%) and unprecedentedly high permeation flux (average 2.32 × 105 L m-2 h-1) are achieved.

Control of Reversible Self-Bending Behavior in Responsive Janus Microstrips.

Here, we demonstrate a simple method to systematically control the responsive self-bending behavior of Janus hydrogel microstrips consisting of a polymeric bilayer with a high modulus contrast. The Janus hydrogel microstrips could be easily fabricated by a simple micromolding technique combined with an initiated chemical vapor deposition (iCVD) coating, providing high flexibility in controlling the physical and chemical properties of the microstrips. The fabricated Janus hydrogel microstrip is composed of a soft, pH-responsive polymer hydrogel layer laminated with a highly cross-linked, rigid thin film, generating a geometric anisotropy at a micron scale. The large difference in the elastic moduli between the two layers of the Janus microstrips leads to a self-bending behavior in response to the pH change. More specifically, the impact of the physical and chemical properties of the microstrip on the self-bending phenomena was systematically investigated by changing the thickness and composition of two layers of the microstrip, which renders high controllability in bending of the microstrips. The curvature of the Janus microstrips, formed by self-bending, highly depends on the applied acidity. A reversible, responsive self-bending/unbending exhibits a perfect resilience pattern with repeated changes in pH for 5 cycles. We envision that the Janus microstrips can be engineered to form complex 3D microstructures applicable to various fields such as soft robotics, scaffolds, and drug delivery. The reliable responsive behaviors obtained from the systematic investigation will provide critical information in bridging the gap between the theoretical mechanical analysis and the chemical properties to achieve micron-scale soft robotics.

Application of monodirectional Janus patch to oromucosal delivery system.

Drug delivery through mucosae has received huge research attention owing to its advantageous characteristics such as accurate dose control and the avoidance of premature metabolism of vulnerable drugs by oral administration. However, body fluid in mucosae may dissolve the drug, releasing it to unwanted directions. Here, a Janus drug delivery patch with monodirectional diffusion property is devised to deliver drugs efficiently and to overcome the issue of unwanted drug release. A polyester fabric is coated with a hydrophobic polymer, poly(3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10-heptadecafluorodecyl methacrylate), via initiated chemical vapor deposition. Subsequently, hydrophilicity is rendered selectively on one surface by base-catalyzed hydrolysis to obtain a Janus substrate with both hydrophobic and hydrophilic surfaces. The hydrophilic surface of the Janus substrate is further coated with resveratrol-loaded hydrogel to produce a Janus drug delivery patch. The fabricated patch efficiently blocks fluid penetration from one side to the other in mucous environment. Delivery of resveratrol through hairless mouse skin and reconstructed human mucosae using Janus patch shows higher permeation flux compared to bare control patch. The Janus drug delivery patch shown in this study can be a useful tool for efficient transmucosal delivery of various kinds of drugs.

Three-dimensional clustering of Janus cylinders by convex curvature and hydrophobic interactions.

The three-dimensional (3D) clustering of Janus cylinders is controlled by simply tuning the cylinder geometry and hydrophobic interactions. Janus cylinders were prepared by combining two approaches: micromolding and initiated chemical vapor deposition (iCVD). Hydrophilic cylinders with a flat- or convex-top curvature were prepared by micromolding based on surface tension-induced flow. The iCVD process then provides a hydrophobic domain through the simple and precise deposition of a polymer film on the top surface, forming monodisperse Janus microcylinders. We use these Janus cylinders as building blocks to form 2D or 3D clusters via hydrophobic interactions in methanol. We investigate how cylinder geometry or degree of hydrophobic interaction affects the resulting cluster geometries. The convex-top Janus cylinders lead to 3D clustering through tip-to-tip interactions, and the flat-top Janus cylinders lead to 2D clustering through face-to-face attraction. The number of Janus cylinders in 3D clusters is tuned by controlling the degree of hydrophobic (or hydrophilic) interaction.

Scalable nanopillar arrays with layer-by-layer patterned overt and covert images.

Transferring flexible and scalable nano-pillar arrays on a variety of unconventional substrates, including fabric, paper, and metals, is achieved by a single-step replication process using UV-curable polymers. Local alteration of the contact angle on the nanopillar arrays by LBL films creates selectively hidden images. They can be revealed by the breath and used as an innovative anti-counterfeit technology.

Simple and reliable method to incorporate the Janus property onto arbitrary porous substrates.

Economical fabrication of waterproof/breathable substrates has many potential applications such as clothing or improved medical dressing. In this work, a facile and reproducible fabrication method was developed to render the Janus property to arbitrary porous substrates. First, a hydrophobic surface was obtained by depositing a fluoropolymer, poly(3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10-heptadecafluorodecyl methacrylate) (PHFDMA), on various porous substrates such as polyester fabric, nylon mesh, and filter paper. With a one-step vapor-phase deposition process, termed as initiated chemical vapor deposition (iCVD), a conformal coating of hydrophobic PHFDMA polymer film was achieved on both faces of the porous substrate. Since the hydrophobic perfluoroalkyl functionality is tethered on PHFDMA via hydrolyzable ester functionality, the hydrophobic functionality on PHFDMA was readily released by hydrolysis reaction. Here, by simply floating the PHFDMA-coated substrates on KOH(aq) solution, only the face of the PHFDMA-coated substrate in contact with the KOH(aq) solution became hydrophilic by the conversion of the fluoroalkyl ester group in the PHFDMA to hydrophilic carboxylic acid functionality. The hydrophilized face was able to easily absorb water, showing a contact angle of less than 37°. However, the top side of the PHFDMA-coated substrate was unaffected by the exposure to KOH(aq) solution and remained hydrophobic. Moreover, the carboxylated surface was further functionalized with aminated polystyrene beads. The porous Janus substrates fabricated using this method can be applied to various kinds of clothing such as pants and shirts, something that the lamination process for Gore-tex has not allowed.

reliable Synthesis of Monodisperse Microparticles: Prevention of Oxygen Diffusion and Organic Solvents Using Conformal Polymeric Coating onto Poly(dimethylsiloxane) Micromold.

An effective polymeric thin film deposited by initiated chemical vapor deposition (iCVD) process was presented and its application as a barrier film on the PDMS micromold blocking the penetration of oxygen and organic solvents was investigated. With this barrier film, we were able to synthesize monodisperse polymeric particles of sizes down to 3 µm, which has been reported to be extremely challenging with bare PDMS micromold. The polymeric barrier film on the PDMS micromold enabled this successful synthesis of microparticles by effectively blocking the diffusion of oxygen, which is a well-known radical quencher in radical polymerization, through the PDMS micromold. Furthermore, the iCVD barrier film substantially decreased the penetration of various organic solvents such as acetone, tert-butanol, PDMS oil, and decane as well as organic substances including fluorescent molecules like rhodamine B and fluorescein isothiocyanate (FITC). Therefore, the polymeric barrier film coated on PDMS micromold via iCVD process will broaden the application of PDMS to microfluidic area for the synthesis of smaller microparticles with various organic substances.