High intensity vanadium beam for synthesis of new superheavy elements with well-controlled emittance by using "slit triplet".

To provide a very powerful vanadium (V) beam with an intensity of at least 6 particle µA for synthesizing a new superheavy element (SHE) with atomic number Z = 119, we have developed a high-temperature oven (HTO) system to evaporate the metallic V powder inside the new superconducting (SC) electron cyclotron ion source. We successfully extracted a V13+ beam with a maximum beam intensity of 600 eµA with 2.8-kW microwave power and 900-W heating power of the HTO. Furthermore, from a systematic study of the dependence of the beam intensity on the microwave power and the HTO power, we successfully produced a V13+ beam of 300 eµA at a consumption rate of 3 mg/h, allowing a one-month duration continuous beam to carry out the SHE synthesis. In addition, to avoid serious damage to newly introduced SC acceleration cavities by beam losses, the beam should be transported with a well-controlled emittance. To efficiently limit the beam emittance, we employed a slit triplet consisting of three pairs of slits installed around the focus point of the low-energy beam transport. The first result of the emittance reduction was observed by a pepper-pot type emittance meter as a function of the acceptance of the slit triplet.

Control system for the new RIKEN 28-GHz superconducting electron cyclotron resonance ion source for SRILAC.

A new RIKEN 28-GHz superconducting electron cyclotron resonance ion source (SC-ECRIS) has been installed for the superconducting RIKEN linear accelerator (SRILAC). The new SC-ECRIS control system mainly consists of programmable logic controllers (PLCs) embedded with the Experimental Physics and Industrial Control System. To improve the reliability as compared with previous control systems, two types of PLC central processing units, sequential and Linux, have been installed in the same unit. Past experience has shown that new types of designs that can rapidly respond to system scalability are key. By connecting PLC stations using star-topology field buses, their rapid and cost-effective response to system changes is realized for the new devices. Furthermore, a unique data acquisition system employing a 920-MHz-band radio was developed to measure analog data such as the temperature at the high-voltage stage.

Progress in high-temperature oven development for 28 GHz electron cyclotron resonance ion source.

We have been developing a high-temperature oven using UO2 in the 28 GHz superconducting electron cyclotron resonance ion source at RIKEN since 2013. A total of eleven on-line tests were performed. The longest operation time in a single test was 411 h, and the consumption rate of UO2 was approximately 2.4 mg/h. In these tests, we experienced several problems: the ejection hole of a crucible was blocked with UO2 and a crucible was damaged because of the reduction of tungsten strength at high temperature. In order to solve these problems, improvements to the crucible shape were made by simulations using ANSYS.

Development of a high-temperature oven for the 28 GHz electron cyclotron resonance ion source.

We have been developing the 28 GHz ECR ion source in order to accelerate high-intensity uranium beams at the RIKEN RI-beam Factory. Although we have generated U(35+) beams by the sputtering method thus far, we began developing a high-temperature oven with the aim of increasing and stabilizing the beams. Because the oven method uses UO2, a crucible must be heated to a temperature higher than 2000 °C to supply an appropriate amount of UO2 vapor to the ECR plasma. Our high-temperature oven uses a tungsten crucible joule-heated with DC current of approximately 450 A. Its inside dimensions are ϕ11 mm × 13.5 mm. Since the crucible is placed in a magnetic field of approximately 3 T, it is subject to a magnetic force of approximately 40 N. Therefore, we used ANSYS to carefully design the crucible, which was manufactured by machining a tungsten rod. We could raise the oven up to 1900 °C in the first off-line test. Subsequently, UO2 was loaded into the crucible, and the oven was installed in the 28 GHz ECR ion source and was tested. As a result, a U(35+) beam current of 150 µA was extracted successfully at a RF power of approximately 3 kW.

Recent development of RIKEN 28 GHz superconducting electron cyclotron resonance ion source.

Over the past two years, we have tried to improve the performance of the RIKEN superconducting electron cyclotron resonance ion source using several methods. For the production of U vapor, we chose the sputtering method because it is possible to install a large amount of material inside the plasma chamber and thus achieve long-term operation without a break, although it is assumed that the beam intensity is weaker than in the oven technique. We also used an aluminum chamber instead of a stainless steel one. Using these methods, we successfully produced ∼180 eµA of U(35+) and ∼230 eµA of U(33+) at the injected radio frequency (RF) power of ∼4 kW (28 GHz). Very recently, to further increase the beam intensity of U(35+), we have started to develop a high temperature oven and have successfully produced a highly charged U ion beam. In this contribution, we report on the beam intensity of highly charged U ions as a function of various parameters (RF power and sputtering voltage) and discuss the effects of these parameters on the beam stability in detail.

Results of RIKEN superconducting electron cyclotron resonance ion source with 28 GHz.

We measured the beam intensity of highly charged heavy ions and x-ray heat load for RIKEN superconducting electron cyclotron resonance ion source with 28 GHz microwaves under the various conditions. The beam intensity of Xe(20+) became maximum at B(min) ∼ 0.65 T, which was ∼65% of the magnetic field strength of electron cyclotron resonance (B(ECR)) for 28 GHz microwaves. We observed that the heat load of x-ray increased with decreasing gas pressure and field gradient at resonance zone. It seems that the beam intensity of highly charged heavy ions with 28 GHz is higher than that with 18 GHz at same RF power.

Production of a highly charged uranium ion beam with RIKEN superconducting electron cyclotron resonance ion source.

A highly charged uranium (U) ion beam is produced from the RIKEN superconducting electron cyclotron resonance ion source using 18 and 28 GHz microwaves. The sputtering method is used to produce this U ion beam. The beam intensity is strongly dependent on the rod position and sputtering voltage. We observe that the emittance of U(35+) for 28 GHz microwaves is almost the same as that for 18 GHz microwaves. It seems that the beam intensity of U ions produced using 28 GHz microwaves is higher than that produced using 18 GHz microwaves at the same Radio Frequency (RF) power.

First results from the new RIKEN superconducting electron cyclotron resonance ion source (invited).

The next generation heavy ion accelerator facility, such as the RIKEN radio isotope (RI) beam factory, requires an intense beam of high charged heavy ions. In the past decade, performance of the electron cyclotron resonance (ECR) ion sources has been dramatically improved with increasing the magnetic field and rf frequency to enhance the density and confinement time of plasma. Furthermore, the effects of the key parameters (magnetic field configuration, gas pressure, etc.) on the ECR plasma have been revealed. Such basic studies give us how to optimize the ion source structure. Based on these studies and modern superconducting (SC) technology, we successfully constructed the new 28 GHz SC-ECRIS, which has a flexible magnetic field configuration to enlarge the ECR zone and to optimize the field gradient at ECR point. Using it, we investigated the effect of ECR zone size, magnetic field configuration, and biased disk on the beam intensity of the highly charged heavy ions with 18 GHz microwaves. In this article, we present the structure of the ion source and first experimental results with 18 GHz microwave in detail.

High temperatures activate local viral multiplication and cell-to-cell movement of Melon necrotic spot virus but restrict expression of systemic symptoms.

The infection of melon plants by Melon necrotic spot virus (MNSV) and the development of necrotic disease symptoms are a seasonal occurrence in Japan, which take place between winter and early summer, but not during mid-summer. In this paper we investigate the effect of three different temperatures (15, 20, and 25 degrees C) on the local and systemic expression of MNSV in melon plants. Previously, the incidence of plants expressing systemic symptoms caused by MNSV and other viruses was found to be greater at temperatures less than 20 degrees C. In this study, our temperature-shift experiments support previous studies that found the expression of systemic symptoms increases as temperature falls from 25 to 20 degrees C and decreases as temperature rises from 20 to 25 degrees C. However, MNSV replication in melon cells and local viral movement within leaves following the inoculation of melon protoplasts or cotyledons were more frequent at 25 degrees C than at 15 or 20 degrees C.

Frankliniella cephalica, a New Vector for Tomato spotted wilt virus.

Frankliniella cephalica (Crawford) is an invasive species of thrips found in the islands of Yaeyama in the Okinawa Prefecture, Japan. During the late 1990s to early 2000s, a species of thrips was isolated from wild flowers of Bidens pilosa L. and Ipomoea batatas L. growing close to cultivated fields. They were subsequently identified as F. cephalica using fine morphological characteristics with the help of Steve Nakahara (U.S. Department of Agriculture, Beltsville, MD) and Laurence Mound (CSIRO, Australia). Voucher specimens were deposited in the Laboratory of Insect Resources, Faculty of Agriculture, Tokyo University of Agriculture by Shuji Okajima (2). We investigated the ability of F. cephalica to vector Tomato spotted wilt virus (TSWV) by experimentally determining virus transmission efficiency. Newly hatched larvae as much as 12 h old underwent a viral acquisition-access period (AAP) of 24 h, during which they fed on the leaves of Datura stramonium infected with TSWV-O, a Japanese type isolate. Transmission efficiency of adults 4 days after emergence from molt (14 days after the AAP) was determined by a petunia leaf disk assay (3) in which the adults were individually allowed to feed for successive 24-h inoculation access periods (IAP) on two different leaf disks of Petunia × hybrida cv. Polo Blue. Transmission of the virus by the adults was considered positive if at least one of the leaf disks showed viral necrotic spot. We tested 20 randomly selected leaf disks with clear necrotic spots using a simplified rapid immunofilter paper assay. All selected disks were positive for TWSV. The transmission efficiencies were 24.6% for female (n = 57) and 54.4% for male (n = 125) adults. The efficiency was significantly different between sexes (Fisher's exact probability test, P < 0.001). We also examined changes in the virus infection site at different developmental stages in thrips using immunofluorescence microscopy with a polyclonal antibody to N protein of the virus (4). After a 6-h AAP feeding by first instar larvae, the virus was found initially to infect the epithelial cells and then spread throughout the midgut tissue in the second instar larvae 5 days after acquisition of the virus. In viruliferous adults, the virus was present in the salivary glands and on the basement membrane of the midgut tissue. These data indicate that F. cephalica is a new insect vector for TSWV. F. cephalica is a major insect pest of tropical crops in tropical and subtropical coastal belts (1). The presence of a thrips vector in weed hosts surrounding cultivated fields might increase the chance of crops in this habitat becoming infected with viruses. References: (1) M. Lamberts and J. H. Crane. Page 337 in: Advances in New Crops. J. Janick and J. E. Simon, eds. Timber Press, Portland, OR, 1990. (2) M. Masumoto and S. Okajima. Jpn. J. Appl. Entomol. Zool. 48:225, 2004. (3) T. Sakurai et al. Appl. Entomol. Zool. 39:71, 2004. (4) S. Tsuda et al. Ann. Phytopathol. Soc. Jpn. 60:216, 1994.

A gene homologous to beta-type carbonic anhydrase is essential for the growth of Corynebacterium glutamicum under atmospheric conditions.

Carbonic anhydrase catalyzes the interconversion of CO(2) and bicarbonate. We focused on this enzyme in the amino acid-producing organism Corynebacterium glutamicum in order to assess the availability of bicarbonate for carboxylation reactions essential to growth and for those required for L-lysine overproduction. A whole-genome sequence revealed two genes encoding putative beta-type and gamma-type carbonic anhydrases in C. glutamicum. These genes encode polypeptides containing zinc ligands strictly conserved in each type of carbonic anhydrase and were designated bca and gca, respectively. Internal deletion of the chromosomal bca gene resulted in a phenotype showing severely reduced growth under atmospheric conditions (0.04% CO(2)) on both complete and minimal media. The growth defect of the Delta bca strain was restored under elevated CO(2) conditions (5% CO(2)). Introduction of the red alga Porphyridium purpureum carbonic anhydrase gene ( pca) could compensate for the bca deletion, allowing normal growth under an atmospheric level of CO(2). In contrast, the Delta gca strain behaved identically to the wild-type strain with respect to growth, irrespective of the CO(2) conditions. Attempts to increase the dosage of bca, gca, and pca in the defined L-lysine-producing strain C. glutamicum AHD-2 led to no discernable effects on growth and production. Northern blot analysis indicated that the bca transcript in strain AHD-2 and another L-lysine producer, C. glutamicum B-6, was present at a much higher level than in the wild-type strain, particularly during exponential growth phases. These results indicate that: (1) the bca product is essential to achieving normal growth under ordinary atmospheric conditions, and this effect is most likely due to the bca product's ability to maintain favorable intracellular bicarbonate/CO(2) levels, and (2) the expression of bca is induced during exponential growth phases and also in the case of L-lysine overproduction, both of which are conditions of higher bicarbonate demand.

Efficient 40 degrees C fermentation of L-lysine by a new Corynebacterium glutamicum mutant developed by genome breeding.

We have recently developed a new L-lysine-producing mutant of Corynebacterium glutamicum by "genome breeding" consisting of characterization and reconstitution of a mutation set essential for high-level production. The strain AHP-3 was examined for L-lysine fermentation on glucose at temperatures above 35 degrees C, at which no examples of efficient L-lysine production have been reported for this organism. We found that the strain had inherited the thermotolerance that the original coryneform bacteria was endowed with, and thereby grew and produced L-lysine efficiently up to 41 degrees C. A final titer of 85 g/l after only 28 h was achieved at temperatures around 40 degrees C, indicating the superior performance of the strain developed by genome breeding. When compared with the traditional 30 degrees C fermentation, the 40 degrees C fermentation allowed an increase in yield of about 20% with a concomitant decrease in final growth level, suggesting a significant transition of carbon flux distribution in glucose metabolism. DNA array analysis of metabolic changes between the 30 degrees C and 40 degrees C fermentations identified several differentially expressed genes in central carbon metabolism although we could not find stringent control-like global induction of amino-acid-biosynthetic genes in the 40 degrees C fermentation. Among these changes, two candidates were picked out as the potential causes of the increased production at 40 degrees C; decreased expression of the citrate synthase gene gltA and increased expression of malE, the product of which involves regeneration of pyruvate and NADPH.

ER stress induces caspase-8 activation, stimulating cytochrome c release and caspase-9 activation.

Excess ER stress induces caspase-12 activation and/or cytochrome c release, causing caspase-9 activation. Little is known about their relationship during ER stress-mediated cell death. Upon ER stress, P19 embryonal carcinoma (EC) cells showed activation of various caspases, including caspase-3, caspase-8, caspase-9, and caspase-12, and extensive DNA fragmentation. We examined the relationship between ER stress-mediated cytochrome c/caspase-9 and caspase-12 activation by using caspase-9- and caspase-8-deficient mouse embryonic fibroblasts and a P19 EC cell clone [P19-36/12 (-) cells] lacking expression of caspase-12. Caspase-9 and caspase-8 deficiency inhibited and delayed the onset of DNA fragmentation but did not inhibit caspase-12 processing induced by ER stress. P19-36/12 (-) cells underwent apoptosis upon ER stress, with cytochrome c release and caspase-8 and caspase-9 activation. The dominant negative form of FADD and z-VAD-fmk inhibited caspase-8, caspase-9, Bid processing, cytochrome c release, and DNA fragmentation induced by ER stress, suggesting that caspase-8 and caspase-9 are the main caspases involved in ER stress-mediated apoptosis of P19-36/12 (-) cells. Caspase-8 deficiency also inhibited the cytochrome c release induced by ER stress. Thus, in parallel with the caspase-12 activation, ER stress triggers caspase-8 activation, resulting in cytochrome c/caspase-9 activation via Bid processing.

A novel methodology employing Corynebacterium glutamicum genome information to generate a new L-lysine-producing mutant.

Classical whole-cell mutagenesis has achieved great success in development of many industrial fermentation strains, but has the serious disadvantage of accumulation of uncharacterized secondary mutations that are detrimental to their performance. In the post-genomic era, a novel methodology which avoids this drawback presents itself. This "genome-based strain reconstruction" involves identifying mutations by comparative genomic analysis, defining mutations beneficial for production, and assembling them in a single wild-type background. Described herein is an initial challenge involving reconstruction of classically derived L-lysine-producing Corynebacterium glutamicum. Comparative genomic analysis for the relevant terminal pathways, the efflux step, and the anaplerotic reactions between the wild-type and production strains identified a Val-59-->Ala mutation in the homoserine dehydrogenase gene (hom), a Thr-311-->Ile mutation in the aspartokinase gene (lysC), and a Pro-458-->Ser mutation in the pyruvate carboxylase gene (pyc). Introduction of the hom and lysC mutations into the wild-type strain by allelic replacement resulted in accumulation of 8 g and 55 g of L-lysine/l, respectively, indicating that both these specific mutations are relevant to production. The two mutations were then reconstituted in the wild-type genome, which led to a synergistic effect on production (75 g/l). Further introduction of the pyc mutation resulted in an additional contribution and accumulation of 80 g/l after only 27 h. This high-speed fermentation achieved the highest productivity (3.0 g l(-1) h(-1)) so far reported for microbes producing L-lysine in fed-batch fermentation.

Tumour invasion and metastasis are promoted in mice deficient in tenascin-X.

BACKGROUND: Tenascin-X (TNX) is a member of the tenascin family of large oligomeric glycoproteins of the extracellular matrix (ECM). To determine whether TNX plays a part in tumour invasion and metastasis and to disclose its normal physiological role, we disrupted its gene in mouse embryonic stem cells by homologous recombination and created mice deficient in TNX. RESULTS: TNX-null mutant (TNX-/-) mice arose at normal frequency and showed no obvious defects during their adult life. However, when TNX-/- mice were subcutaneously inoculated in foot-pads with a highly invasive and metastatic cell line, B16-BL6 melanoma cells, the primary tumour size at 30 days after inoculation in the TNX-/- mice had increased by 1.2-fold compared with that in wild-type mice, and the invasion to the ankle and pulmonary metastasis in TNX-/- mice were also augmented by 2.2-fold and 6.8-fold, respectively, compared to those in wild-type mice. To disclose the molecular mechanism(s) of the promotion of tumour invasion and metastasis in TNX-/- mice, we measured the protein levels of matrix metalloproteinases (MMPs), which are recognized as playing a key role in these events, in the foot-pad homogenates of TNX-/- mice prior to the inoculation of melanoma cells. Gelatin zymography showed that the activities of proMMP-2, active MMP-2 and proMMP-9 were significantly higher in TNX-/- mice than in wild-type mice. Furthermore, a Northern blot analysis demonstrated that this increased activity of MMP-2 in TNX-/- mice was due to the induced expression of MMP-2 at the transcriptional level. The elevated expression of MMP-2 and MMP-9 resulted in decreased laminin levels, to less than half that of wild-type mice in the homogenates of TNX-/- mice. CONCLUSIONS: TNX deficiency led to an increase in the production of MMPs, and the increased activity of MMPs may result in the degradation of laminin. Consequently, the melanoma cells inoculated in TNX-/- mice might facilitate invasion and metastasis. These results imply that TNX is required for impeding the invasion and metastasis of tumour cells.

Fused heterocyclic antioxidants: antioxidative activities of hydrocoumarins in a homogeneous solution.

We compared the antioxidative activities of seven hydrocoumarins with those of alpha-tocopherol for the oxidation of tetralin and linoleic acid in a homogeneous solution. Hydrocoumarins exhibited a higher induction period than that of alpha-Toc in both systems. However, the rate of oxygen absorption during the induction period for alpha-Toc was slower than that of the hydrocoumarins in both systems. In addition, 6,7-dihydroxy-4,4-dimethylhydrocoumarin showed less cytotoxicity toward human fibroblasts than did 2,6-di-t-butyl-4-methylphenol.

Cloning and characterization of a rat ortholog of MMP-23 (matrix metalloproteinase-23), a unique type of membrane-anchored matrix metalloproteinase and conditioned switching of its expression during the ovarian follicular development.

In our attempt to study the role of matrix metalloproteinases (MMPs) in the process of mammalian ovulation, we isolated a rat ortholog of the recently reported human MMP-23 from gonadotropin-primed immature rat ovaries. Transient expression of epitope-tagged rat and human MMP-23 in COS-1 cells revealed that they were synthesized as a membrane-anchored glycoprotein with type II topology. Indirect immunofluorescent analysis showed that subcellular localization of MMP-23 was predominantly in the perinuclear regions. The transfected human MMP-23 protein was processed endogenously to the soluble form in COS-1 cells. However, cotransfection of MMP-23 with the mouse furin cDNA did not enhance this processing, indicating that furin may not be involved in this event. Notably, in situ hybridization analysis revealed a dramatic switching of MMP-23 mRNA localization from granulosa cells to theca-externa/fibroblasts and ovarian surface epithelium during the follicular development. In serum-free primary culture of rat granulosa cells, a drastic diminution of MMP-23 mRNA expression was observed in response to FSH action between 24 h and 48 h of culture. The observed effect of FSH on MMP-23 expression was mimicked by treatment of granulosa cells with forskolin or 8-bromo (Br)-cAMP. In contrast, MMP-23 mRNA levels increased in theca-interstitial cells regardless of the presence of LH in the culture. However, treatment of theca-interstitial cells with forskolin or 8-Br-cAMP markedly reduced the expression of MMP-23 with a concomitant increase in progesterone production. These results indicate that the MMP-23 gene is spatially and temporally regulated in a cell type-specific manner in ovary via the cAMP signaling pathway.

Contrasts in tick innate immune responses to Borrelia burgdorferi challenge: immunotolerance in Ixodes scapularis versus immunocompetence in Dermacentor variabilis (Acari: Ixodidae).

The blacklegged tick, Ixodes scapularis Say, transmits the Lyme disease spirochete Borrelia burgdorferi, whereas the American dog tick, Dermacentor variabilis (Say), is unable to transmit the bacterium. We compared the innate immune response of these ticks against spirochetes directly inoculated into the hemocoel cavity of ticks. In I. scapularis, some Borrelia were found associated with hemocytes, while numerous other spiral-shaped, intact bacteria remained free in the hemolymph. In contrast, in D. variabilis only remnants of the bacteria were evident in the hemolymph, indicating lysis; intact spirochetes were rare. Spirochetes were observed bound to or within the organs of both tick species, although many more spirochetes were found associated with the I. scapularis organs. The few spirochetes observed with the D. variabilis organs appeared to be dead because D. variabilis tissues rarely contained culturable bacteria, unlike I. scapularis tissues. When spirochetes were incubated with I. scapularis hemolymph plasma in vitro, bacterial survival and motility were not reduced. In contrast, incubation of spirochetes with D. variabilis hemolymph plasma resulted in > 50% of the spirochetes becoming nonmotile by 45 min. The differences in the responses of the two different tick species indicate that I. scapularis is immunotolerant when challenged with B. burgdorferi and dependent on a slow phagocytic response to clear Borrelia from the hemolymph. In contrast, D. variabilis is highly immunocompetent (i.e., innate immunity), using plasma borreliacidal factors and a rapid increase in phagocytic cells to clear the infection and limit tissue invasion.