Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 2 de 2
Filtrar
Mais filtros










Base de dados
Intervalo de ano de publicação
1.
Ann Biomed Eng ; 51(7): 1513-1522, 2023 Jul.
Artigo em Inglês | MEDLINE | ID: mdl-36841890

RESUMO

The use of ovine animal models in the study of injury biomechanics and modeling is increasing, due to their favorable size and other physiological characteristics. Along with this increase, there has also been increased interest in the development of in silico ovine models for computational studies to compliment physical experiments. However, there remains a gap in the literature characterizing the morphological and mechanical characteristics of ovine ribs. The objective of this study therefore is to report anatomical and mechanical properties of the ovine ribs using microtomography (micro-CT) and two types of mechanical testing (quasi-static bending and dynamic tension). Using microtomography, young ovine rib samples obtained from a local abattoir were cut into approximately fourteen 38 mm sections and scanned. From these scans, the cortical bone thickness and cross-sectional area were measured, and the moment of inertia was calculated to enhance the mechanical testing data. Based on a standard least squares statistical model, the cortical bone thickness varied depending on the region of the cross-section and the position along the length of the rib (p < 0.05), whereas the cross-sectional area remained consistent (p > 0.05). Quasi-static three-point bend testing was completed on ovine rib samples, and the resulting force-displacement data was analyzed to obtain the stiffness (44.67 ± 17.65 N/mm), maximum load (170.54 ± 48.28 N) and displacement at maximum load (7.19 ± 2.75 mm), yield load (167.81 ± 48.12 N) and displacement at yield (6.10 ± 2.25 mm), and the failure load (110.90 ± 39.30 N) and displacement at failure (18.43 ± 2.10 mm). The resulting properties were not significantly affected by the rib (p > 0.05), but by the animal they originated from (p < 0.05). For the dynamic testing, samples were cut into coupons and tested in tension with an average strain rate of 18.9 strain/sec. The resulting dynamic testing properties of elastic modulus (5.16 ± 2.03 GPa), failure stress (63.29 ± 14.02 MPa), and failure strain (0.0201 ± 0.0052) did not vary based on loading rate (p > 0.05).


Assuntos
Fenômenos Mecânicos , Costelas , Ovinos , Animais , Microtomografia por Raio-X , Costelas/diagnóstico por imagem , Costelas/lesões , Osso Cortical/anatomia & histologia , Fenômenos Biomecânicos , Estresse Mecânico
2.
Annu Int Conf IEEE Eng Med Biol Soc ; 2020: 3634-3637, 2020 07.
Artigo em Inglês | MEDLINE | ID: mdl-33018789

RESUMO

Deep brain stimulation (DBS) involves activation of targeted brain tissue through implantable electrodes to treat neurological disorders. In this study, two novel electrode designs, recessed flat-contact and recessed curvature-contact models were developed where the electrode contacts were recessed to a specified depth to improve directional selectivity. Furthermore, the contact geometry was also modified for the recessed curvature-contact model in order to obtain a hemispherical configuration that will help increase current steering and reduce the propensity of tissue damage. The predicted tissue damage produced by these models were compared to the standard array model using the Shannon tissue damage model criteria. Furthermore, the volume of tissue activated by each of the electrode models was analyzed, and the radial projection relative to the total projection of each geometry was determined as a measure of directional selectivity. Based on the trends observed in the current density, tissue damage, and volume of tissue activated (VTA) analyses, it is inferred that the recessed contact electrode geometries help improve directional selectivity and safety of DBS.


Assuntos
Estimulação Encefálica Profunda , Encéfalo , Eletrodos Implantados , Matemática , Modelos Neurológicos
SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA
...