Recent Advances in Phosphorene: Structure, Synthesis, and Properties.

Phosphorene is a 2D phosphorus atomic layer arranged in a honeycomb lattice like graphene but with a buckled structure. Since its exfoliation from black phosphorus in 2014, phosphorene has attracted tremendous research interest both in terms of synthesis and fundamental research, as well as in potential applications. Recently, significant attention in phosphorene is motivated not only by research on its fundamental physical properties as a novel 2D semiconductor material, such as tunable bandgap, strong in-plane anisotropy, and high carrier mobility, but also by the study of its wide range of potential applications, such as electronic, optoelectronic, and spintronic devices, energy conversion and storage devices. However, a lot of avenues remain to be explored including the fundamental properties of phosphorene and its device applications. This review recalls the current state of the art of phosphorene and its derivatives, touching upon topics on structure, synthesis, characterization, properties, stability, and applications. The current needs and future opportunities for phosphorene are also discussed.

Pathways of Water-Induced Lead-Halide Perovskite Surface Degradation: Insights from In Situ Atomic-Scale Analysis.

While organic-inorganic hybrid perovskites are emerging as promising materials for next-generation photovoltaic applications, the origins and pathways of perovskite instability remain speculative. In particular, the degradation of perovskite surfaces by ambient water is a crucial subject for determining the long-term viability of perovskite-based solar cells. Here, we conducted surface characterization and atomic-scale analysis of the reaction mechanisms for methylammonium lead bromide (MA(CH3NH3)PbBr3) single crystals using ambient-pressure atomic force microscopy (AP-AFM) and near-ambient-pressure X-ray photoelectron spectroscopy (NAP-XPS) in environments ranging from ultrahigh vacuum to 0.01 mbar of water vapor. MAPbBr3 single crystals, grown by a solution process, were mechanically cleaved under UHV conditions to obtain an atomically clean surface. Consecutive topography and friction force measurements in low-pressure water (pwater ≈ 10-5 mbar) revealed the formation of degraded patches, one atomic layer deep, gradually increasing their coverage until the surface was entirely covered at a water exposure of 4.7 × 104 langmuir (L). At the perimeters of these degraded patches, a higher friction coefficient was observed, along with an interstitial step height, which we attribute to a structure equivalent to that of the MA-Br terminated surface. Combined with NAP-XPS analysis, our results demonstrate that water vapor induces the dissociation of surface methylammonium ligands, eventually resulting in the depletion of the surface MA and the full coverage of hydrocarbon species after exposure to 0.01 mbar of water vapor.

Modulation of perovskite degradation with multiple-barrier for light-heat stable perovskite solar cells.

The long-term stability of perovskite solar cells remains one of the most important challenges for the commercialization of this emerging photovoltaic technology. Here, we adopt a non-noble metal/metal oxide/polymer multiple-barrier to suppress the halide consumption and gaseous perovskite decomposition products release with the chemically inert bismuth electrode and Al2O3/parylene thin-film encapsulation, as well as the tightly closed system created by the multiple-barrier to jointly suppress the degradation of perovskite solar cells, allowing the corresponding decomposition reactions to reach benign equilibria. The resulting encapsulated formamidinium cesium-based perovskite solar cells with multiple-barrier maintain 90% of their initial efficiencies after continuous operation at 45 °C for 5200 h and 93% of their initial efficiency after continuous operation at 75 °C for 1000 h under 1 sun equivalent white-light LED illumination.

Local Built-In Field at the Sub-nanometric Heterointerface Mediates Cascade Electrochemical Conversion of Lithium-sulfur Batteries.

Heterogeneous catalytic mediators have been proposed to play a vital role in enhancing the multiorder reaction and nucleation kinetics in multielectron sulfur electrochemistry. However, the predictive design of heterogeneous catalysts is still challenging, owing to the lack of in-depth understanding of interfacial electronic states and electron transfer on cascade reaction in Li-S batteries. Here, a heterogeneous catalytic mediator based on monodispersed titanium carbide sub-nanoclusters embedded in titanium dioxide nanobelts is reported. The tunable catalytic and anchoring effects of the resulting catalyst are achieved by the redistribution of localized electrons caused by the abundant built-in fields in heterointerfaces. Subsequently, the resulting sulfur cathodes deliver an areal capacity of 5.6 mAh cm-2 and excellent stability at 1 C under sulfur loading of 8.0 mg cm-2 . The catalytic mechanism especially on enhancing the multiorder reaction kinetic of polysulfides is further demonstrated via operando time-resolved Raman spectroscopy during the reduction process in conjunction with theoretical analysis.

Graphene-Like Conjugated Molecule as Hole-Selective Contact for Operationally Stable Inverted Perovskite Solar Cells and Modules.

Further enhancing the operational lifetime of inverted-structure perovskite solar cells (PSCs) is crucial for their commercialization, and the design of hole-selective contacts at the illumination side plays a key role in operational stability. In this work, the self-anchoring benzo[rst]pentaphene (SA-BPP) is developed as a new type of hole-selective contact toward long-term operationally stable inverted PSCs. The SA-BPP molecule with a graphene-like conjugated structure shows a higher photostability and mobility than that of the frequently-used triphenylamine and carbazole-based hole-selective molecules. Besides, the anchoring groups of SA-BPP promote the formation of a large-scale uniform hole contact on ITO substrate and efficiently passivate the perovskite absorbers. Benefiting from these merits, the champion efficiencies of 22.03% for the small-sized cells and 17.08% for 5 × 5 cm2 solar modules on an aperture area of 22.4 cm2 are achieved based on this SA-BPP contact. Also, the SA-BPP-based device exhibits promising operational stability, with an efficiency retention of 87.4% after 2000 h continuous operation at the maximum power point under simulated 1-sun illumination, which indicates an estimated T80 lifetime of 3175 h. This novel design concept of hole-selective contacts provides a promising strategy for further improving the PSC stability.

Heterogeneous FASnI3 Absorber with Enhanced Electric Field for High-Performance Lead-Free Perovskite Solar Cells.

Lead-free tin perovskite solar cells (PSCs) have undergone rapid development in recent years and are regarded as a promising eco-friendly photovoltaic technology. However, a strategy to suppress charge recombination via a built-in electric field inside a tin perovskite crystal is still lacking. In the present study, a formamidinium tin iodide (FASnI3) perovskite absorber with a vertical Sn2+ gradient was fabricated using a Lewis base-assisted recrystallization method to enhance the built-in electric field and minimize the bulk recombination loss inside the tin perovskites. Depth-dependent X-ray photoelectron spectroscopy revealed that the Fermi level upshifts with an increase in Sn2+ content from the bottom to the top in this heterogeneous FASnI3 film, which generates an additional electric field to prevent the trapping of photo-induced electrons and holes. Consequently, the Sn2+-gradient FASnI3 absorber exhibits a promising efficiency of 13.82% for inverted tin PSCs with an open-circuit voltage increase of 130 mV, and the optimized cell maintains over 13% efficiency after continuous operation under 1-sun illumination for 1,000 h.

Atomic Level Insights into Metal Halide Perovskite Materials by Scanning Tunneling Microscopy and Spectroscopy.

Metal halide perovskite materials (MHPMs) have attracted significant attention because of their superior optoelectronic properties and versatile applications. The power conversion efficiency of MHPM solar cells (PSCs) has skyrocketed to 25.5 %. Although the performance of PSCs is already competitive, several important challenges still need to be solved to realize commercial applications. A thorough understanding of surface atomic structures and structure-property relationships is at the heart of these remaining issues. Scanning tunneling microscopy (STM) and spectroscopy (STS) can be used to characterize the surface properties of MHPMs, which can offer crucial insights into MHPMs at the atomic scale. This Review summarizes recent progress in STM and STS studies on MHPMs, with a focus on the surface properties. We provide understanding from the comparative perspective of several different MHPMs. We also highlight a series of novel phenomena observed by STM and STS. Finally, we outline a few research topics of primary importance for future studies.

Spectral Stable Blue-Light-Emitting Diodes via Asymmetric Organic Diamine Based Dion-Jacobson Perovskites.

The spectral instability issue is a challenge in blue perovskite light-emitting diodes (PeLEDs). Dion-Jacobson (DJ) phase perovskites are promising alternatives to achieve high-quality blue PeLEDs. However, the current exploration of DJ phase perovskites is focused on symmetric divalent cations, and the corresponding efficiency of blue PeLEDs is still inferior to that of green and red ones. In this work, we report a new type of DJ phase CsPb(Br/Cl)3 perovskite via introduction of an asymmetric molecular configuration as the organic spacer cation in perovskites. The primary and tertiary ammonium groups on the asymmetric cations bridge with the lead halide octahedra forming the DJ phase structures. Stable photoluminescence spectra were demonstrated in perovskite films owing to the suppressed halide segregation. Meanwhile, the radiative recombination efficiency of charges is improved significantly as a result of the confinement effects and passivation of charge traps. Finally, we achieved an external quantum efficiency of 2.65% in blue PeLEDs with stable spectra emission under applied bias voltages. To our best knowledge, this is the first report of asymmetric cations used in PeLEDs, which provides a facile solution to the halide segregation issue in PeLEDs.

Atomic Scale Investigation of the CuPc-MAPbX3 Interface and the Effect of Non-Stoichiometric Perovskite Films on Interfacial Structures.

Metal halide perovskites (MHPs) have become a major topic of research in thin film photovoltaics due to their advantageous optoelectronic properties. These devices typically have the MHP absorber layer sandwiched between two charge selective layers (CSLs). The interfaces between the perovskite layer and these CSLs are potential areas of higher charge recombination. Understanding the nature of these interfaces is key for device improvement. Additionally, non-stoichiometric perovskite films are expected to strongly impact the interfacial properties. In this study, the interface between CH3NH3PbI3 (MAPbI3) and copper phthalocyanine (CuPc), a hole transport layer (HTL), is studied at the atomic scale. We use scanning tunneling microscopy (STM) combined with density functional theory (DFT) predictions to show that CuPc deposited on MAPbX3 (X = I,Br) forms a self-assembled layer consistent with the α-polymorph of CuPc. Additionally, STM images show a distinctly different adsorption orientation for CuPc on non-perovskite domains of the thin film samples. These findings highlight the effect of non-stoichiometric films on the relative orientation at the MHP/HTL interface, which may affect interfacial charge transport in a device. Our work provides an atomic scale view of the MHP/CuPc interface and underscores the importance of understanding interfacial structures and the effect that the film stoichiometry can have on interfacial properties.

Long-life lithium-sulfur batteries with high areal capacity based on coaxial CNTs@TiN-TiO2 sponge.

Rational design of heterostructures opens up new opportunities as an ideal catalyst system for lithium polysulfides conversion in lithium-sulfur battery. However, its traditional fabrication process is complex, which makes it difficult to reasonably control the content and distribution of each component. In this work, to rationally design the heterostructure, the atomic layer deposition is utilized to hybridize the TiO2-TiN heterostructure with the three-dimensional carbon nanotube sponge. Through optimizing the deposited thickness of TiO2 and TiN layers and adopting the annealing post-treatment, the derived coaxial sponge with uniform TiN-TiO2 heterostructure exhibits the best catalytic ability. The corresponding lithium-sulfur battery shows enhanced electrochemical performance with high specific capacity of 1289 mAh g-1 at 1 C and capacity retention of 85% after 500 cycles at 2 C. Furthermore, benefiting from the highly porous structure and interconnected conductive pathways from the sponge, its areal capacity reaches up to 21.5 mAh cm-2.

Up-Scalable Fabrication of SnO2 with Multifunctional Interface for High Performance Perovskite Solar Modules.

Tin dioxide (SnO2) has been demonstrated as one of the promising electron transport layers for high-efficiency perovskite solar cells (PSCs). However, scalable fabrication of SnO2 films with uniform coverage, desirable thickness and a low defect density in perovskite solar modules (PSMs) is still challenging. Here, we report preparation of high-quality large-area SnO2 films by chemical bath deposition (CBD) with the addition of KMnO4. The strong oxidizing nature of KMnO4 promotes the conversion from Sn(II) to Sn(VI), leading to reduced trap defects and a higher carrier mobility of SnO2. In addition, K ions diffuse into the perovskite film resulting in larger grain sizes, passivated grain boundaries, and reduced hysteresis of PSCs. Furthermore, Mn ion doping improves both the crystallinity and the phase stability of the perovskite film. Such a multifunctional interface engineering strategy enabled us to achieve a power conversion efficiency (PCE) of 21.70% with less hysteresis for lab-scale PSCs. Using this method, we also fabricated 5 × 5 and 10 × 10 cm2 PSMs, which showed PCEs of 15.62% and 11.80% (active area PCEs are 17.26% and 13.72%), respectively. For the encapsulated 5 × 5 cm2 PSM, we obtained a T80 operation lifetime (the lifespan during which the solar module PCE drops to 80% of its initial value) exceeding 1000 h in ambient condition.

Lead halide-templated crystallization of methylamine-free perovskite for efficient photovoltaic modules.

Upscaling efficient and stable perovskite layers is one of the most challenging issues in the commercialization of perovskite solar cells. Here, a lead halide-templated crystallization strategy is developed for printing formamidinium (FA)-cesium (Cs) lead triiodide perovskite films. High-quality large-area films are achieved through controlled nucleation and growth of a lead halide•N-methyl-2-pyrrolidone adduct that can react in situ with embedded FAI/CsI to directly form α-phase perovskite, sidestepping the phase transformation from δ-phase. A nonencapsulated device with 23% efficiency and excellent long-term thermal stability (at 85°C) in ambient air (~80% efficiency retention after 500 hours) is achieved with further addition of potassium hexafluorophosphate. The slot die-printed minimodules achieve champion efficiencies of 20.42% (certified efficiency 19.3%) and 19.54% with an active area of 17.1 and 65.0 square centimeters, respectively.

Slot-die coating large-area formamidinium-cesium perovskite film for efficient and stable parallel solar module.

Perovskite solar cells have emerged as one of the most promising thin-film photovoltaic (PV) technologies and have made a strong debut in the PV field. However, they still face difficulties with up-scaling to module-level devices and long-term stability issue. Here, we report the use of a room-temperature nonvolatile Lewis base additive, diphenyl sulfoxide(DPSO), in formamidinium-cesium (FACs) perovskite precursor solution to enhance the nucleation barrier and stabilize the wet precursor film for the scalable fabrication of uniform, large-area FACs perovskite films. With a parallel-interconnected module design, the resultant solar module realized a certified quasi-stabilized efficiency of 16.63% with an active area of 20.77 cm2 The encapsulated modules maintained 97 and 95% of their initial efficiencies after 10,000 and 1187 hours under day/night cycling and 1-sun equivalent white-light light-emitting diode array illumination with maximum power point tracking at 50°C, respectively.

Inverse Growth of Large-Grain-Size and Stable Inorganic Perovskite Micronanowire Photodetectors.

Control of forward and inverse reactions between perovskites and precursor materials is key to attaining high-quality perovskite materials. Many techniques focus on synthesizing nanostructured CsPbX3 materials (e.g., nanowires) via a forward reaction (CsX + PbX2 → CsPbX3). However, low solubility of inorganic perovskites and complex phase transition make it difficult to realize the precise control of composition and length of nanowires using the conventional forward approach. Herein, we report the self-assembly inverse growth of CsPbBr3 micronanowires (MWs) (CsPb2Br5 → CsPbBr3 + PbBr2↑) by controlling phase transition from CsPb2Br5 to CsPbBr3. The two-dimensional (2D) structure of CsPb2Br5 serves as nucleation sites to induce initial CsPbBr3 MW growth. Also, phase transition allows crystal rearrangement and slows down crystal growth, which facilitates the MW growth of CsPbBr3 crystals along the 2D planes of CsPb2Br5. A CsPbBr3 MW photodetector constructed based on the inverse growth shows a high responsivity of 6.44 A W-1 and detectivity of ∼1012 Jones. Large grain size, high crystallinity, and large thickness can effectively alleviate decomposition/degradation of perovskites, which leads to storage stability for over 60 days in humid environment (relative humidity = 45%) and operational stability for over 3000 min under illumination (wavelength = 400 nm, light intensity = 20.06 mW cm-2).

Imaging of the Atomic Structure of All-Inorganic Halide Perovskites.

All-inorganic halide perovskites are promising materials for optoelectronic applications. The surface or interface structure of the perovskites plays a crucial role in determining the optoelectronic conversion efficiency, as well as the material stability. A thorough understanding of surface atomic structures of the inorganic perovskites and their contributions to their optoelectronic properties and stability is lacking. Here we show a scanning tunneling microscopy investigation on the atomic and electronic structure of CsPbBr3 perovskite. Two different surface structures with a stripe and an armchair domain are identified, which originates from a complex interplay between Cs cations and Br anions. Our findings are further supported and correlated with density functional theory calculations and photoemission spectroscopy measurements. The stability evaluation of photovoltaic devices indicates a higher stability for CsPbBr3 in comparison with MAPbBr3, which is closely related to the low volatility of Cs from the perovskite surface.

Reducing Detrimental Defects for High-Performance Metal Halide Perovskite Solar Cells.

In several photovoltaic (PV) technologies, the presence of electronic defects within the semiconductor band gap limit the efficiency, reproducibility, as well as lifetime. Metal halide perovskites (MHPs) have drawn great attention because of their excellent photovoltaic properties that can be achieved even without a very strict film-growth control processing. Much has been done theoretically in describing the different point defects in MHPs. Herein, we discuss the experimental challenges in thoroughly characterizing the defects in MHPs such as, experimental assignment of the type of defects, defects densities, and the energy positions within the band gap induced by these defects. The second topic of this Review is passivation strategies. Based on a literature survey, the different types of defects that are important to consider and need to be minimized are examined. A complete fundamental understanding of defect nature in MHPs is needed to further improve their optoelectronic functionalities.

Surface Defect Dynamics in Organic-Inorganic Hybrid Perovskites: From Mechanism to Interfacial Properties.

Organic-inorganic hybrid perovskites (OHPs) have garnered much attention among the photovoltaic and light-emitting diode research community due to their excellent optoelectronic properties and low-cost fabrication. Defects in perovskites have been proposed to affect device efficiency and stability and to have a potential role in enabling ion migration. In this study, the dynamic behavior and electronic properties of intrinsic defects in CH3NH3PbBr3 (MAPbBr3) were explored at the atomic scale. We use scanning tunneling microscopy to show unambiguously the occurrence of vacancy-assisted transport of individual ions as well as the existence of vacancy defect clusters at the OHP surface. We combine these observations with density functional theory (DFT) calculations to identify the mechanisms for this ion motion and show that ion transport energy barriers, as well as transport mechanisms, at the surface depend on crystal direction. DFT calculations also reveal that vacancy defect clusters can significantly modify the local work function of the perovskite surface, which is then expected to alter interfacial charge transport in a device. Our work provides a microscopic insight into the mechanism of ion migration in OHPs and also delivers the useful information for device improvement from the perspective of interface engineering.

Thermodynamically stabilized ß-CsPbI3-based perovskite solar cells with efficiencies >18.

Although ß-CsPbI3 has a bandgap favorable for application in tandem solar cells, depositing and stabilizing ß-CsPbI3 experimentally has remained a challenge. We obtained highly crystalline ß-CsPbI3 films with an extended spectral response and enhanced phase stability. Synchrotron-based x-ray scattering revealed the presence of highly oriented ß-CsPbI3 grains, and sensitive elemental analyses-including inductively coupled plasma mass spectrometry and time-of-flight secondary ion mass spectrometry-confirmed their all-inorganic composition. We further mitigated the effects of cracks and pinholes in the perovskite layer by surface treating with choline iodide, which increased the charge-carrier lifetime and improved the energy-level alignment between the ß-CsPbI3 absorber layer and carrier-selective contacts. The perovskite solar cells made from the treated material have highly reproducible and stable efficiencies reaching 18.4% under 45 ± 5°C ambient conditions.

Significant THz absorption in CH3NH2 molecular defect-incorporated organic-inorganic hybrid perovskite thin film.

The valid strong THz absorption at 1.58 THz was probed in the organic-inorganic hybrid perovskite thin film, CH3NH3PbI3, fabricated by sequential vacuum evaporation method. In usual solution-based methods such as 2-step solution and antisolvent, we observed the relatively weak two main absorption peaks at 0.95 and 1.87 THz. The measured absorption spectrum is analyzed by density-functional theory calculations. The modes at 0.95 and 1.87 THz are assigned to the Pb-I vibrations of the inorganic components in the tetragonal phase. By contrast, the origin of the 1.58 THz absorption is due to the structural deformation of Pb-I bonding at the grain boundary incorporated with a CH3NH2 molecular defect.

Degradation Mechanism and Relative Stability of Methylammonium Halide Based Perovskites Analyzed on the Basis of Acid-Base Theory.

The correct identification of all gases released during hybrid perovskite degradation is of great significance to develop strategies to extend the lifespan of any device based on this semiconductor. CH3X (X = Br/I) is a released degradation gas/low boiling point liquid arising from methylammonium (MA+) based perovskites, which has been largely overlooked in the literature focusing on stability of perovskite solar cells. Herein, we present an unambiguous identification of CH3I release using microwave (rotational) spectroscopy. An experimental back-reaction test demonstrates that the well-known CH3NH2/HX degradation route may not be the ultimate degradation pathway of MAPbX3 in thermodynamic closed systems. Meanwhile, the CH3X/NH3 route cannot back-react selectively to MAX formation as occurred for the former back-reaction. Metadynamics calculations uncover the X halide effect on energy barriers for both degradation reactions showing a better stability of Br based perovskite ascribed to two aspects: (i) lower Brönsted-Lowry acidity of HBr compared to HI and (ii) higher nucleophilic character of CH3NH2 compared to NH3. The latter property makes CH3NH2 molecules stay preferentially attached on the electrophilic perovskite surface (Pb2+) during the dynamic simulation instead of being detached as observed for the NH3 molecule.