Viable Properties of Natural Rubber/Halloysite Nanotubes Composites Affected by Various Silanes.

Natural rubber (NR) is incompatible with hydrophilic additives like halloysite nanotubes (HNT) due to their different polarity. The silane coupling agent is the ideal component to include in such a compound to solve this problem. Many types of silane are available for polymer composites depending on their functionalities. This work aimed to tune it to the composite based on NR and HNT. Four different silanes, namely Bis[3- (Triethoxysilyl)Propyl]Tetrasulfide (TESPT), 3-Aminopropyl triethoxysilane (APTES), N-[3-(Trimethoxysilyl)Propyl] Ethylenediamine (AEAPTMS), and Vinyltrimethoxysilane (VTMS) were used. Here, the mechanical properties were used to assess the properties, paying close attention to how their reinforcement influenced their crystallization behavior after stretching. It was revealed that adding silane coupling agents greatly improved the composites' modulus, tensile strength, and tear strength. From the overall findings, AEAPTMS was viable for NR/HNT composites. This was in direct agreement with the interactions between NR and HNT that silanes had encouraged. The findings from stress-strain curves describing the crystallization of the composites are in good agreement with the findings from synchrotron wide-angle X-ray scattering (WAXS). The corresponding silanes have substantially aided the strain-induced crystallization (SIC) of composites.

Potency of Urea-Treated Halloysite Nanotubes for the Simultaneous Boosting of Mechanical Properties and Crystallization of Epoxidized Natural Rubber Composites.

Halloysite nanotubes (HNTs) are naturally occurring tubular clay made of aluminosilicate sheets rolled several times. HNT has been used to reinforce many rubbers. However, the narrow diameter of this configuration causes HNT to have poor interfacial contact with the rubber matrix. Therefore, increasing the distance between layers could improve interfacial contact with the matrix. In this work, Epoxidized Natural Rubber (ENR)/HNT was the focus. The HNT layer distance was successfully increased by a urea-mechanochemical process. Attachment of urea onto HNT was verified by FTIR, where new peaks appeared around 3505 cm-1 and 3396 cm-1, corresponding to urea's functionalities. The intercalation of urea to the distance gallery of HNT was revealed by XRD. It was also found that the use of urea-treated HNT improved the modulus, tensile strength, and tear strength of the composites. This was clearly responsible for interactions between ENR and urea-treated HNT. It was further verified by observing the Payne effect. The value of the Payne effect was found to be reduced at 62.38% after using urea for treatment. As for the strain-induced crystallization (SIC) of the composites, the stress-strain curves correlated well with the results from synchrotron wide-angle X-ray scattering.

Effect of extraction methods on the molecular structure and thermal stability of kenaf (Hibiscus cannabinus core) biomass as an alternative bio-filler for rubber composites.

Lignin from kenaf (Hibiscus cannabinus) core was investigated as an alternative filler for rubber. Three types of extraction methods were used to isolate lignin from kenaf, namely kraft, soda and organosolv process. The particle size, surface area, functionalities changes, molecular weight and thermal properties of the lignin were characterized. The results showed that Kraft lignin (KL) has the smallest particle size (40.41 µm) compared to soda lignin (SL) (63.85 µm) and organosolv lignin (OL) (66.85 µm). This is in good agreement with the BET surface area of 9.52 m2/g, 1.25 m2/g and 2.40 m2/g respectively. However, the smaller surface area of SL compared to OL is due to the smaller pore size and pore volume of SL. KL also showed high hydroxyl content with corresponding high thermal stability as confirmed by NMR and TGA. The thermal stability of the lignin correlates well with the molecular weight (MW). From the overall characteristics, it can be concluded that KL, SL and OL can be used as an alternative filler in rubber compounds to substitute common fillers like silica and carbon.

Preparation and Characterization of Low-Molecular-Weight Natural Rubber Latex via Photodegradation Catalyzed by Nano TiO2.

Natural rubber is one of the most important renewable biopolymers used in many applications due to its special properties that cannot be easily mimicked by synthetic polymers. To sustain the existence of natural rubber in industries, modifications have been made to its chemical structure from time to time in order to obtain new properties and to enable it to be employed in new applications. The chemical structure of natural rubber can be modified by exposure to ultraviolet light to reduce its molecular weight. Under controlled conditions, the natural rubber chains will be broken by photodegradation to yield low-molecular-weight natural rubber. The aim of this work was to obtain what is known as liquid natural rubber via photodegradation, with titanium dioxide nanocrystals as the catalyst. Titanium dioxide, which was firstly synthesized using the sol⁻gel method, was confirmed to be in the form of an anatase, with a size of about 10 nm. In this work, the photodegradation was carried out in latex state and yielded low-molecular-weight natural rubber latex of less than 10,000 g/mol. The presence of hydroxyl and carbonyl groups on the liquid natural rubber (LNR) chains was observed, resulting from the breaking of the chains. Scanning electron microscopy of the NR latex particles showed that titanium dioxide nanocrystals were embedded on the latex surface, but then detached during the degradation reaction.