Green and fast determination of the alcoholic content of wines using thermal infrared enthalpimetry.

An innovative use of thermal infrared enthalpimetry (TIE) is proposed for the determination of alcoholic content of red and white wines. Notwithstanding the presence of ethanol in beverages, absolute ethanol was added directly to wines, and the temperature rise caused by the heat of dilution was monitored using an infrared camera. Analytical signals were obtained in only 10 s for four samples simultaneously, and a calibration curve was constructed with hydroalcoholic reference solutions. A linear calibration curve was obtained from 3.0 to 18.0% (v/v) ethanol (R2 = 0.9987). The results showed agreement ranging from 98.2 to 104.0% with 942.06 and 969.12 methods of AOAC. Organic compounds (e.g., sugar) did not interfere in the determinations. The proposed method provided fast results, with a throughput of 480 samples per hour and negligible energy consumption (0.001 kWh). In addition, the consumption of reagents was reduced when compared with conventional method fulfilling green analytical chemistry requirements.

Focused microwave-induced combustion: a new technique for sample digestion.

A procedure for sample digestion based on focused microwave-induced combustion (FMIC) is proposed. This system was developed using a commercial focused microwave oven with a lab-made quartz sample holder and a modified glass vessel. Oxygen flow was used to start and support the combustion. A botanical sample was used to evaluate the operational conditions for further Al, Ba, Ca, Fe, Mg, Mn, Sr, and Zn determination by inductively coupled plasma optical emission spectrometry. Pelletized samples were positioned on the quartz holder, and 50 microL of 6 mol L(-1) NH(4)NO(3) solution was added as igniter. Combustion was completed in less than 2 min, and the temperature was higher than 950 degrees C. The use of a reflux step, the position of sample holder inside the vessel, sample mass, ignition and combustion time, oxygen flow rate, and condenser type were evaluated. Results were compared with those obtained by focused microwave-assisted wet digestion and by high pressure microwave-assisted wet digestion. Agreement of 95-103% was obtained for certified reference materials digested by FMIC (reflux step with 10 mL of 4 mol L(-1) HNO(3)). With the proposed procedure, a complete sample decomposition (residual carbon content lower than 0.5%) was achieved with low consumption of reagents as only 10 mL of diluted nitric acid was necessary. Low relative standard deviation (lower than 3.8%) was observed and high amount of sample (up to 1500 mg) could be digested that allowed lower limits of detection.

Evaluation of sample preparation methods for elastomer digestion for further halogens determination.

In this work, three sample preparation methods were evaluated for further halogen determination in elastomers containing high concentrations of carbon black. Samples of nitrile-butadiene rubber, styrene-butadiene rubber, and ethylene-propylene-diene monomer elastomers were decomposed using oxygen flask combustion and microwave-induced combustion (MIC) for further Br and Cl determination by ion chromatography (IC), inductively coupled plasma optical emission spectrometry (ICP OES), and inductively coupled plasma mass spectrometry (ICP-MS). Extraction assisted by microwave radiation in closed vessels was also evaluated using water or alkaline solution. Digestion by MIC was carried out using 50 mmol l(-1) (NH(4))(2)CO(3) as the absorbing solution. The effect of the reflux step was also evaluated. Accuracy was evaluated using certified reference materials with polymeric matrix composition and by comparison of results using neutron activation analysis. Agreement for Br and Cl was better than 95% by MIC using 5 min of reflux, and no statistical difference was found using IC, ICP OES, and ICP-MS for determination of both analytes. For MIC, the relative standard deviation (RSD) was lower than 5%. Using extraction in closed vessels, a high amount of residues was observed, and recoveries were lower than 45% for both analytes. For oxygen flask combustion, the agreement was similar using MIC but RSD was higher (20%). The residual carbon content, an important parameter used to evaluate the digestion efficiency, was always below 1% for MIC. Using MIC, it was possible to digest elastomers with high efficiency, resulting in a single solution suitable for halogen determination by different techniques.

Comparison of advanced processes on the oxidation of acid orange 7 dye.

The degradation of acid orange 7 dye (AO7) was studied using a 1 L semi-batch tank stirred glass reactor for performing three different photochemical processes (photoperoxidation, Fenton, photo-Fenton). A commercial low pressure lamp was used for irradiation of samples. The advancement of degradation was monitored by measurement of color reduction, UV-spectra, HPLC-UV and COD. The obtained results showed that the photo-Fenton treatment was the most effective for the degradation of AO7.