Tuning the water intrinsic permeability of PEGDA hydrogel membranes by adding free PEG chains of varying molar masses.

We explore the effect of poly(ethylene glycol) (PEG) molar mass on the intrinsic permeability and structural characteristics of poly(ethylene glycol) diacrylate PEGDA/PEG composite hydrogel membranes. We observe that by varying the PEG content and molar mass, we can finely adjust the water intrinsic permeability by several orders of magnitude. Notably, we show the existence of maximum water intrinsic permeability, already identified in a previous study to be located at the critical overlap concentration C* of PEG chains, for the highest PEG molar mass studied. Furthermore, we note that the maximum intrinsic permeability follows a non-monotonic evolution with respect to the PEG molar mass and reaches its peak at 35 000 g mol-1. Besides, our results show that a significant fraction of PEG chains is irreversibly trapped within the PEGDA matrix even for the lowest molar masses down to 600 g mol-1. This observation suggests the possibility of covalent grafting of the PEG chains onto the PEGDA matrix. CryoSEM and AFM measurements demonstrate the presence of large micron-sized cavities separated by PEGDA-rich walls whose nanometric structures strongly depend on the PEG content. By combining our permeability and structural measurements, we suggest that the PEG chains trapped inside the PEGDA-rich walls induce nanoscale defects in the crosslinking density, resulting in increased permeability below C*. Conversely, above C*, we speculate that partially trapped PEG chains may form a brush-like arrangement on the surface of the PEGDA-rich walls, leading to a reduction in permeability. These two opposing effects are anticipated to exhibit molar-mass-dependent trends, contributing to the non-monotonic variation of the maximum intrinsic permeability at C*. Overall, our results demonstrate the potential to fine-tune the properties of hydrogel membranes, offering new opportunities for separation applications.

Relation between oxidation kinetics and reactant transport in an aqueous foam.

HYPOTHESIS: Aqueous foams are expected to constitute exquisite particularly suitable reactive medium for the oxidation of metals, since the reactant H+ can be supplied through the continuous liquid phase, while the reactant O2 can be transported through the gas bubbles. EXPERIMENTS: To test this hypothesis, we investigated the oxidation of a metallic copper cylinder immersed in an aqueous foam. To study the relation between the transport of these reactants and the kinetics of the chemical reaction we use a forced drainage setup which enables us to control both the advection velocity of the H+ ions through the foam and the foam liquid fraction. FINDINGS: We find experimentally that the mass of dissolved copper presents a maximum with the drainage flow rate, and thus with the foam liquid fraction. Modeling analytically the transfer of H+ and O2 through the foams enables us to show that this non-monotonic behavior results from a competition between the advective flux of H+ ions and the unsteady diffusion of O2 through the thin liquid films which tends to be slower as the area of the thin liquid films decreases with the drainage flow rate and the liquid fraction. This study shows for the first time how to optimize the foam structure and drainage flow in reactive foams in which the reactants are present both in the liquid and gaseous phases.

Formation and stabilization of multiple w/o/w emulsions encapsulating catechin, by mechanical and microfluidic methods using a single pH-sensitive copolymer: Effect of copolymer/drug interaction.

Multiple w/o/w emulsions (MEs) are promising systems for protecting fragile hydrophilic drugs and controlling their release. We explore the capacity of a single pH-sensitive copolymer, PDMS60-b-PDMAEMA50, and salts, to form and stabilize MEs loaded with sucrose or catechin by a one-step mechanical process or a microfluidic method. ME cytotoxicity was evaluated in various conditions of pH. Using the mechanical process, the most stable emulsions were obtained with Miglyol®812 N and isopropyl myristate in a final pH range of 8-12 and [0.3 M-1 M] NaCl concentrations. Conversely, with the microfluidic method, isopropyl myristate at pH 3 without salt was more efficient. Catechin strongly affected the formation of droplets by the mechanical process but did not modify the conditions of stability of MEs obtained by the microfluidic method. The antioxidant power of catechin was preserved in the inner droplets, even in emulsions prepared by the mechanical method at pH 8. An incomplete release of sucrose and catechin from the emulsions was observed and attributed to the interaction of molecules with the copolymer through hydrogen bonding. This study highlights some of the barriers to break to formulate multiple emulsions stabilized by a PDMS-b-PDMAEMA copolymer or other polymers which can form hydrogen bonds interaction with encapsulated drugs.

Growth Mechanism of Polymer Membranes Obtained by H-Bonding Across Immiscible Liquid Interfaces.

Complexation of polymers at liquid interfaces is an emerging technique to produce all-liquid printable and self-healing devices and membranes. It is crucial to control the assembly process, but the mechanisms at play remain unclear. Using two different reflectometric methods, we investigate the spontaneous growth of H-bonded PPO-PMAA (polypropylene oxide-polymetacrylic acid) membranes at a flat liquid-liquid interface. We find that the membrane thickness h grows with time t as h ∼ t1/2, which is reminiscent of a diffusion-limited process. However, counterintuitively, we observe that this process is faster as the PPO molar mass increases. We are able to rationalize these results with a model which considers the diffusion of the PPO chains within the growing membrane. The architecture of the latter is described as a gel-like porous network, with a pore size much smaller than the radius of the diffusing PPO chains, thus inducing entropic barriers that hinder the diffusion process. From the comparison between the experimental data and the result of the model, we extract some key piece of information about the microscopic structure of the membrane. This study opens the route toward the rational design of self-assembled membranes and capsules with optimal properties.

Controlled Synthesis of Gold Nanoparticles in Copolymers Nanomolds by X-ray Radiolysis.

We show by X-ray and neutron small-angle scattering that gold nanoparticles with controlled sizes and morphologies can be obtained by the metallic reduction of AuCl4- ions trapped in 3D organic molds by X-ray radiolysis. The molds are spherical frozen micelles of polystyrene-b-poly(dimethylaminoethyl methacrylate) (PS-b-PDMAEMA) block copolymer in acidic aqueous solution with a PS spherical core surrounded by a corona of PDMAEMA chains in good solvent. The behavior of micelles is controlled by the [AuCl4-]/[DMAEMA] ratio RAuCl4-/DMAEMA. At low gold concentration, AuCl4- ions condense on the positively charged DMAEMA moieties without changing the behavior of the PDMAEMA chains. At intermediate gold concentration, the ions induce a progressive contraction of the corona's chains and dehydration of micelles. At large gold concentration, the corona becomes a fully dry phase loaded with gold ions, which induces micelle aggregation. Radiolysis of the solution by an intense X-ray beam produces different types of gold nanoparticles with respect to RAuCl4-/DMAEMA and irradiation time. At RAuCl4-/DMAEMA = 0.033, irradiation produces in the first step gold clusters in the micelle corona which in the second step merge to form nanoparticles of a similar size to that of the micelle. Conversely, at RAuCl4-/DMAEMA = 0.33, micelles do not operate as templates but only as nucleation zones and large nanoparticles grow outside the micelles.

One-Step Fabrication of pH-Responsive Membranes and Microcapsules through Interfacial H-Bond Polymer Complexation.

Biocompatible microencapsulation is of widespread interest for the targeted delivery of active species in fields such as pharmaceuticals, cosmetics and agro-chemistry. Capsules obtained by the self-assembly of polymers at interfaces enable the combination of responsiveness to stimuli, biocompatibility and scaled up production. Here, we present a one-step method to produce in situ membranes at oil-water interfaces, based on the hydrogen bond complexation of polymers between H-bond acceptor and donor in the oil and aqueous phases, respectively. This robust process is realized through different methods, to obtain capsules of various sizes, from the micrometer scale using microfluidics or rotor-stator emulsification up to the centimeter scale using drop dripping. The polymer layer exhibits unique self-healing and pH-responsive properties. The membrane is viscoelastic at pH = 3, softens as pH is progressively raised, and eventually dissolves above pH = 6 to release the oil phase. This one-step method of preparation paves the way to the production of large quantities of functional capsules.

Biocompatible Stimuli-Responsive W/O/W Multiple Emulsions Prepared by One-Step Mixing with a Single Diblock Copolymer Emulsifier.

Multiple water-in-oil-in-water (W/O/W) emulsions are promising materials in designing carriers of hydrophilic molecules or drug delivery systems, provided stability issues are solved and biocompatible chemicals can be used. In this work, we designed a biocompatible amphiphilic copolymer, poly(dimethylsiloxane)-b-poly(2-(dimethylamino)ethyl methacrylate) (PDMS-b-PDMAEMA), that can stabilize emulsions made with various biocompatible oils. The hydrophilic/hydrophobic properties of the copolymer can be adjusted using both pH and ionic strength stimuli. Consequently, the making of O/W (oil in water), W/O (water in oil), and W/O/W emulsions can be achieved by sweeping the pH and ionic strength. Of importance, W/O/W emulsions are formulated over a large pH and ionic strength domain in a one-step emulsification process via transitional phase inversion and are stable for several months. Cryo-TEM and interfacial tension studies show that the formation of these W/O/W emulsions is likely to be correlated to the interfacial film curvature and microemulsion morphology.

Interfacial Rheology of Hydrogen-Bonded Polymer Multilayers Assembled at Liquid Interfaces: Influence of Anchoring Energy and Hydrophobic Interactions.

We study the 2D rheological properties of hydrogen-bonded polymer multilayers assembled directly at dodecane-water and air-water interfaces using pendant drop/bubble dilation and the double-wall ring method for interfacial shear. We use poly(vinylpyrrolidone) (PVP) as a proton acceptor and a series of polyacrylic acids as proton donors. The PAA series of chains with varying hydrophobicity was fashioned from poly(acrylic acid), (PAA), polymethacrylic acid (PMAA), and a homemade hydrophobically modified polymer. The latter consisted of a PAA backbone covalently grafted with C12 moieties at 1% mol (referred to as PAA-1C12). Replacing PAA with the more hydrophobic PMAA provides a route for combining hydrogen bonding and hydrophobic interactions to increase the strength and/or the number of links connecting the polyacid chains to PVP. This systematic replacement allows for control of the ability of the monomer units inside the absorbed polymer layer to reorganize as the interface is sheared or compressed. Consequently, the interplay of hydrogen bonding and hydrophobic interactions leads to control of the resistance of the polymer multilayers to both shear and dilation. Using PAA-1C12 as the first layer improves the anchoring energy of a few monomers of the chain without changing the strength of the monomer-monomer contact in the complex layer. In this way, the layer does not resist shear but resists compression. This strategy provides the means for using hydrophobicity to control the interfacial dynamics of the complexes adsorbed at the interface of the bubbles and droplets that either elongate or buckle upon compression. Moreover, we demonstrate the pH responsiveness of these interfacial multilayers by adding aliquots of NaOH to the acidic water subphase surrounding the bubbles and droplets. Subsequent pH changes can eventually break the polymer complex, providing opportunities for encapsulation/release applications.

Interplay of Hydrogen Bonding and Hydrophobic Interactions to Control the Mechanical Properties of Polymer Multilayers at the Oil-Water Interface.

We probe the mechanical shear and compression properties of hydrogen-bonded polymer multilayers directly assembled at the oil-water interface using interfacial rheology techniques. We show that the polymer multilayers behave mechanically like a transient network, with elastic moduli that can be varied over 2 orders of magnitude by controlling the type and strength of physical interactions involved in the multilayers, which are controlled by the pH and the hydrophobicity of the polymer. Indeed, the interplay of hydrogen and hydrophobic interactions enables one to obtain a tighter and stronger network at the interface. Moreover, we show how a simple LBL process applied directly on emulsion droplets leads to encapsulation of a model oil, dodecane, as well as perfume molecules.

Multiple emulsions controlled by stimuli-responsive polymers.

The phase inversion of water-toluene emulsions stabilized with a single thermo- and pH-sensitive copolymer occurs through the formation of multiple emulsions. At low pH and ambient temperature, oil in water emulsions are formed which transform into highly stable multiple emulsions at pHs immediately lower than the inversion border. At higher pHs, the emulsion turns into a water in oil one.

Poly(N-isopropylacrylamide) microgels at the oil-water interface: interfacial properties as a function of temperature.

Highly monodisperse poly(N-isopropylacrylamide), PNiPAM, microgels were prepared by the conventional radical polymerization of NiPAM in the presence of dimethylamino ethyl methacrylate (DMAEMA) monomers at various concentrations. The effect of DMAEMA on the polymerization of PNiPAM microgels was examined at constant initiator (V50) and cross-linker (MBA) concentrations. The presence of DMAEMA in the synthesis batch allows for the preparation of PNiPAM microgels with controlled size and a narrow size distribution. The oil(dodecane)/water interfacial properties of the model PNiPAM microgels were then investigated. The pendant drop technique was used to measure the interfacial tensions as a function of temperature. Over the whole range of temperature (20-45 degrees C), the interfacial tension remains low (on the order of 17 mN/m) and goes through a minimum (12 mN/m) at a temperature of about 34 degrees C, which well matches the volume phase transition temperature (VPTT) of PNiPAM microgels. Below the VPTT, the decrease in the interfacial tension with temperature is likely to be due to the adsorption of dense layers because of the decrease of the excluded volume interactions. Above the VPTT, we suggest that the increase in the interfacial tension with temperature comes from the adsorption of loosely packed PNiPAM microgels. We also studied the effect of temperature on the stability of emulsions. Dodecane in water emulsions, which form at ambient temperature, are destabilized as the temperature exceeds the VPTT. In light of the interfacial tension results, we suggest that emulsion destabilization arises from the adsorption of aggregates above the VPTT and not from an important desorption of microgels. Aggregate adsorption would bring a sufficiently high number of dodecane molecules into contact with water to induce coalescence without changing the interfacial tension very much.

Emulsion stabilization and inversion using a pH- and temperature-sensitive amphiphilic copolymer.

We describe how a versatile amphiphilic diblock copolymer can form oil-in-water (o/w) or water-in-oil (w/o) emulsions depending on pH and temperature. At high pH and temperature, this copolymer is mostly hydrophobic and forms w/o emulsions. Its spontaneous curvature is greatly increased upon pH and/or temperature lowering (due to protonation and/or hydration, respectively), which allows the formation of o/w emulsions. Conductivity measurements and confocal fluorescence micrographs evidence the two kinds of structures obtained over a wide range of pH and temperature. We also show how the emulsion type can be reversibly switched along a temperature scan under stirring. The lower stability of the w/o emulsions as compared to the o/w ones is attributed to a lack of electrostatic repulsion. The importance of the copolymer architecture and conformation with regards to droplet stability is discussed.

Enhancement of transfection efficiency through rapid and noncovalent post-PEGylation of poly(dimethylaminoethyl methacrylate)/DNA complexes.

PURPOSE: The aim of this work was to develop a new strategy to introduce poly(ethylene glycol) (PEG) into methacrylate-based polymer/ DNA complexes in order to produce hemocompatible particles able to transfect cells in the presence of serum. METHODS: Atom transfer radical polymerization was used to synthesize a well-defined poly(2-(dimethylamino)ethyl methacrylate) homopolymer (PDMAEMA) and a poly(2-(dimethylamino)ethyl methacrylate-b-poly(ethylene glycol) alpha-methyl ether, omega-methacrylate) palm-tree-like copolymer (P(DMAEMA-b-MAPEG)). The complexes obtained by self assembly of the pCMVbeta plasmid and the polymers were used to transfect Cos-7 cells. Their physical properties--particle size and zeta potential--were characterized respectively by dynamic light scattering and electrophoretic mobility measurements. Ex vivo hemocompatibility was also determined. RESULTS: The PDMAEMA/pCMVbeta complexes transfected Cos-7 cells exclusively in the absence of serum. Although the P(DMAEMA-bMAPEG) copolymer had no transfection activity per se, the addition of the latter to pre-formed PDMAEMA/DNA complexes significantly enhanced the activity and allowed transfection even in the presence of serum. The presence of palm-tree-like copolymers also improved the hemocompatibility properties of the complexes. No effect on platelet counts was observed for P(DMAEMA-b-MAPEG)/pCMVbeta complexes, whereas a decrease of platelets was clearly observed when blood cells were incubated with PDMAEMA/pCMVbeta complexes. CONCLUSIONS: Such a synergistic effect of noncovalent PEGylation of poly(amino methacrylate)/DNA complexes allows a new and versatile approach to tune up transfection efficiency.

Solvent-free synthesis and purification of poly[2-(dimethylamino)ethyl methacrylate] by atom transfer radical polymerization.

Solvent-free synthesis of well-defined poly[2-(dimethylamino)ethyl methacrylate] (PDMAEMA) (co)polymers was performed by atom transfer radical polymerization conducted under very mild conditions (in bulk at 25 degrees C). The pH-dependence and the thermo-responsive behaviour of PDMAEMA in aqueous solution were operated to isolate and purify the (co)polymers without using any organic solvent or further catalyst extraction. The viscosity in aqueous solution of so-purified PDMAEMA homopolymers and their block copolymers with poly(ethylene glycol) (PEG) was studied as a function of molar mass and concentration and a typical polyelectrolyte behaviour was observed, these catalyst-deprived polycations are able to form stable and non toxic complexes with DNA, showing good transfection efficacies in gene therapy.