Comparing the effects of Al-based coagulants in waste activated sludge anaerobic digestion: Methane yield, kinetics and sludge implications.

Due to its effectiveness and ease of application, the process of flocculation and coagulation is often used for pollution removal in wastewater treatment. Most of these coagulants precipitate and accumulate in waste activated sludge (WAS), and could negatively affect sludge treatments, as observed for anaerobic digestion. Nowadays, wastewater treatment plants (WWTPs) are widely discussed because of the current paradigm shift from linear to circular economy, and the treatments performed at the facility should be planned to avoid or reduce adverse effects on other processes. The aim of this study was to compare the impact of poly aluminum chloride (PAC) and aluminum sulfate (AS) on WAS anaerobic digestion, by feeding replicate serum reactors with different levels of coagulant (5, 10 and 20 mg Al/g TS). Reactors without the addition of any coagulants represented the control group. Results revealed that Al-based coagulants inhibited methane production, which decreased as the coagulant addition increased. The inhibition was much more severe in AS-conditioned reactors, showing average reductions in methane yield from 14.4 to 31.7%, compared to the control (167.76 ± 1.88 mL CH4/g VS). Analytical analysis, FTIR and SEM investigations revealed that the addition of coagulants affected the initial conditions of the anaerobic reactors, penalizing the solubilization, hydrolysis and acidogenesis phases. Furthermore, the massive formation of H2S in AS-conditioned reactors played a key role in the suppression of methane phase. On the other hand, the use of coagulant can promote the accumulation and recovery of nutrient in WAS, especially in terms of phosphorus. Our findings will expand research knowledge in this field and guide stakeholders in the choice of coagulants at full scale plant. Future research should focus on reducing the effect of coagulants on methane production by modifying or testing new types of flocculants.

Removal of heavy metals from dredging marine sediments via electrokinetic hexagonal system: A pilot study in Italy.

Among the several treatment options, electrokinetic (EK) remediation is recognized as an effective technique for the removal of heavy metals from low-permeability porous matrices. However, most of the EK decontamination research reported was performed on linear configuration systems at a laboratory scale. In this study, a series of experiments were performed on a pilot-scale system where the electrodes were arranged in a hexagonal configuration, to assess the improvement of the EK process in the removal of inorganic contaminants from sediments dredged in the harbor of Piombino, Italy. HNO3 was used as acid conditioning and both pH effect and treatment duration time were investigated. Sediment characterization and metal fractionation were also presented, in order to understand how the bioavailability of metals affects the process efficiency. The increase in pH due to the buffering capacity of the sediment in the sections close to the cathode favored the precipitation and accumulation of metals. However, the results highlighted that longer treatment times, combined with an efficient pH reduction, can improve treatment performance, resulting in high removal efficiencies for all the target metals considered (a percentage removal greater than 50% was reached for Cd, Ni, Pb, Cu and Zn). Compared to different EK configuration systems, the hexagonal configuration arrangement applied in our study provides better results for the remediation of dredged marine sediment.

A Fenton-based approach at neutral and un-conditioned pH for recalcitrant COD removal in tannery wastewater: Experimental test and sludge characterization.

The combination of raw animal skin manufacturing processes involves the use of large amounts of chemicals, resulting in the generation of complex and highly polluted tannery wastewater. In this context, the high concentration of chloride in tannery wastewater represents a crucial bottleneck. Indeed, sodium chloride, commonly used in tannery industry to prevent skin rot, increases the concentration of chlorides up to 50 %. At the same time, most of the advanced oxidation processes usually employed in tannery wastewater treatment to remove recalcitrant COD involve the use of conditioning agents, thus increasing the overall concentration of chlorides in the treated effluent. The aim of this study was to evaluate the electrochemical peroxidation process (ECP) efficiency in the treatment of tannery wastewater without changing pH, to improve Fenton technology by avoiding the use of chemicals. The influence of different electric currents on COD and color removal was investigated. The characterization of the produced sludge was conducted through FTIR, SEM and XRD analysis, exploring the morphology and composition of precipitate, depending on the applied current. Although an electrical current of 750 mA yields the highest COD and color removal efficiency (69.7 % and 97.8 %, respectively), 500 mA can be considered the best compromise because of energy consumptions. Iron oxides and hydroxides were generated during the ECP process, playing the role of coagulants through the absorption of organic and inorganic contaminants. The consumption of energy increased as a function of time and applied current; however, cost analysis showed that the electrodes contributed the most to the total cost of the process. In authors' knowledge, the application of ECP process as a tertiary treatment for the removal of recalcitrant COD in tannery wastewater represents a novelty in the literature and the results obtained can be considered as the basis for scaling up the process in future research.

Centralization of wastewater treatment in a tourist area: A comparative LCA considering the impact of seasonal changes.

Nowadays, environmental protection has become a topic of primary importance, and the interest in wastewater treatment plants (WWTPs) has increased due to the need for a paradigm shift from linear to circular economy. The centralization level of wastewater infrastructure is the basis for a successful system. The aim of this study was to investigate the environmental impacts generated from the centralized treatment of wastewater in a tourist area in central Italy. The combined use of BioWin 6.2 simulation software and life cycle assessment (LCA) methodology was implemented to evaluate the potential connection of a small decentralized WWTP to a medium-size centralized facility. Two different scenarios (decentralized system, corresponding to the current situation, and centralized) were evaluated in two separate periods: high season (HS), corresponding to the main tourist season, and low season (LS), which is the period before the main tourist season. Two sensitivity analyses were conducted, assuming different N2O emission factors, and considering the period at the end of tourist season, respectively. Although with modest advantages (up to -6 % in pollutant emissions), WWTP connection was the best management option in 10 out of 11 indicators in HS, and 6 out of 11 categories in LS. The study showed that wastewater centralization was promoted by scale factors in HS, as the most impactful consumptions decreased as the degree of centralization increased; on the other hand, the decentralized system was less penalized in LS, as small WWTP was less stressed and energy consuming in this period. Sensitivity analysis confirmed the results obtained. Site-specific conditions can lead to conflicting circumstances, as key parameters may have different behaviors depending on seasonal variations, and the degree of centralization in tourist areas should be addressed by distinguishing separate periods, based on changes in tourist flows and pollution loads.

A comparative LCA of three WWTPs in a tourist area: Effects of seasonal loading rate variations.

Although the wastewater treatment is a fundamental utility for the protection of human health and the environment, non-evident drawbacks are associated with it. Wastewater treatment plants (WWTPs) located in tourist areas generally suffer from the seasonal increase in wastewater flow-rate and associated pollution loads. In this study, a Life Cycle Assessment (LCA) of three medium-size urban WWTPs, located in a tourist area in central Italy, was carried out. The study compared the environmental impacts generated by 1 m3 of treated wastewater in low season (LS) and high season (HS). All the material and energy flows involved in the operational phase of wastewater treatment were considered within the system boundaries, including the disposal or recovery treatment of the waste streams generated by the WWTPs, namely screenings, waste from grit removal and wastewater sludge. The analysis was conducted using almost only real data from full-scale plants. In each WWTP, the environmental impacts produced in HS were higher than those generated in LS; therefore, the environmental impacts increased as the loading rate increased. Furthermore, a correlation between WWTP size and environmental performance was observed. Indeed, in 8 out of 11 environmental indicators, the percentage increase in pollutant emissions due to wastewater treatment in HS decreased as the WWTP size increased. Results revealed that larger WWTPs suffered less from seasonal loading rate variations, showing greater flexibility. The existence of a scale factor suggests that the centralization of WWTPs in tourist areas can be an option to enable better treatment performance in terms of environmental impacts. A sensitivity analysis was performed, increasing N2O emission factors from wastewater treatment in LS: considering a 75 % increase, the outcomes found in default LCA were not confirmed. Future research should investigate the operational factors and biological mechanisms that most affect wastewater treatment when significant seasonal variations are present.