Effect of basket mesh size on the hydrodynamics of a partially filled (500 mL) USP rotating basket dissolution testing Apparatus 1.

The USP Rotating Basket Dissolution Testing Apparatus 1 is listed in the USP as one of the tools to assess dissolution of oral solid dosage forms. Baskets of different mesh sizes can be used to differentiate between dissolution profiles of different formulations. Here, we used Particle Image Velocimetry (PIV) to study the hydrodynamics of the USP Apparatus 1 using baskets with different mesh openings (10-, 20- and 40-mesh) revolving at 100 rpm, when the vessel was filled with 500 mL. The velocity profiles throughout the liquid were found to vary significantly using baskets of different mesh sizes, typically increasing with increased size of the opening of the basket mesh, especially for axial and radial velocities. This, in turn, resulted in a significantly different flow rate through the basket, which can be expected to significantly impact the dissolution rate of the drug product. A comparison between the results of this work with those of a previous study with a 900-mL fill volume (Sirasitthichoke et al., Intern. J. Pharmaceutics, 2021, 607: 120976), shows that although the hydrodynamics in the USP Apparatus 1 changed with fill level in the vessel, the flow rate through the basket was not significantly affected. This implies that tablets dissolving in the two systems would experience similar tablet-liquid medium mass transfer coefficients, and therefore similar initial dissolution rates, but different dissolution profiles because of the difference in volume.

Doppler Ultrasound Assessment of Tumor Vascularity in Locally Advanced Breast Cancer at Diagnosis and following Primary Systemic Chemotherapy.

Aim: The primary goal of this research is to compare the morphological response, as determined by clinical and sonographic examination, to the gold standard, histology, in assessing the effectiveness of major systemic chemotherapy in patients with locally advanced breast cancer (LABC). Materials and Methods: During the check and before each example of chemotherapy (FAC schedule), 54 patients with privately progressed, non-metastatic breast disease underwent a comprehensive clinical assessment, ultrasonography of the breast and axillae, and assortment and spooky Doppler appraisal to evaluate response to therapy. Results: In 90% of instances, Doppler provided early insight into how a patient might respond to treatment. Disappearance of all vascular signals inside the tumor was shown to be the strongest predictor of full pathological response. Conclusion: Patients with LABC may benefit from using color Doppler to determine how well chemotherapy is working.

A Study on Urinary Isolates of Candida Species Isolated from Hospitalized Patients with Special Reference to Speciation, Antifungal Susceptibility, and Comparison of Rapid and Conventional Methods of Speciation.

Aim: In order to determine which species of Candida were isolated from hospitalized patients' urine, which risk factors they were linked to, and which antifungal drugs were effective against them, the current investigation was carried out. Materials and Methods: One hundred inpatients were part of the study group. Urine samples were collected from each subject and spun at 3000 rpm for 10-15 minutes in individual sterile centrifuge tubes. Color, size, texture, and the presence of color diffusion into the surrounding agar were used to identify the distinct Candida species, presumably in 48 hours. Results: A total of 86.7% of the Candida spp. were found to be non-albicans. Major inaccuracies occurred because of differences between methodologies; thus, MBD is the best way to determine antifungal susceptibility to itraconazole and amphotericin B. Conclusion: To help clinicians decide on an empirical treatment in an emergency, accurate identification of Candida down to the species level is crucial.

Harmonizing Biopredictive Methodologies Through the Product Quality Research Institute (PQRI) Part I: Biopredictive Dissolution of Ibuprofen and Dipyridamole Tablets.

Assessing in vivo performance to inform formulation selection and development decisions is an important aspect of drug development. Biopredictive dissolution methodologies for oral dosage forms have been developed to understand in vivo performance, assist in formulation development/optimization, and forecast the outcome of bioequivalence studies by combining them with simulation tools to predict plasma profiles in humans. However, unlike compendial dissolution methodologies, the various biopredictive methodologies have not yet been harmonized or standardized. This manuscript presents the initial phases of an effort to develop best practices and move toward standardization of the biopredictive methodologies through the Product Quality Research Institute (PQRI, https://pqri.org ) entitled "The standardization of in vitro predictive dissolution methodologies and in silico bioequivalence study Working Group." This Working Group (WG) is comprised of participants from 10 pharmaceutical companies and academic institutes. The project will be accomplished in a total of five phases including assessing the performance of dissolution protocols designed by the individual WG members, and then building "best practice" protocols based on the initial dissolution profiles. After refining the "best practice" protocols to produce equivalent dissolution profiles, those will be combined with physiologically based biopharmaceutics models (PBBM) to predict plasma profiles. In this manuscript, the first two of the five phases are reported, namely generating biopredictive dissolution profiles for ibuprofen and dipyridamole and using those dissolution profiles with PBBM to match the clinical plasma profiles. Key experimental parameters are identified, and this knowledge will be applied to build the "best practice" protocol in the next phase.

Ultrasonic enhanced emulsification process in 3D printed microfluidic device to encapsulate active pharmaceutical ingredients.

A new method to prepare polymer encapsulated repaglinide nanoparticles through ultrasonic enhanced microchannel emulsification technique was explored. Using the concept of 3D printing, three different shaped micromixers (T-type, Y-type, and F-type) followed by a serpentine microchannel was fabricated using SS-316. Parametric study was performed on all three fabricated micromixers. The best results were obtained for the Y-microchannel in a microfluidic system alone, which showed a minimum particle size of 513.6 nm with 75.4% encapsulation efficiency (EE). In the selected microchannel, to further reduce the drug particle size and to increase% EE, convective mixing between immiscible fluids was enhanced by implementing ultrasound. Compared to the microfluidic system, particle size and EE were significantly improved in the ultrasonic microfluidic system. The experimental results revealed that the minimum particle size of 75.4 ± 1.3 nm with 82.9 ± 0.2% EE was achieved using an ultrasonic enhanced microfluidic system. The zeta potential of + 29.5 mV was obtained for emulsion prepared using the ultrasonic microfluidic system, whereas + 22 mV was prepared using a microfluidic system. Moreover, a backscattering measurement was performed to predict the stability of prepared emulsions. Integrating the ultrasound with a microfluidic system has proven beneficial for drug encapsulation.

Influence of basket mesh size on the hydrodynamics in the USP rotating basket dissolution testing Apparatus 1.

The USP Apparatus 1 (rotating basket), typically used to assess drug product reproducibility and evaluate oral solid dosage forms performance, consists of a cylindrical glass vessel with a hemispherical bottom and a wire basket rotating at constant speed. Baskets with different wire openings can be used in alternative to the standard mesh opening (40-mesh) in order to discriminate between drug formulations during early stage of drug product development. Any changes introduced by different basket geometries can potentially and significantly impact the system hydrodynamics and cause variability of results, thus affecting product quality. In this work, Particle Image Velocimetry (PIV) was used to experimentally quantify the velocity distribution in the USP rotating basket Apparatus 1 using baskets of different mesh sizes (10-, 20-, and 40-mesh size) under the typical operating conditions described in dissolution testing procedures. Similar flow patterns were observed in all cases. However, the radial and axial velocities in the USP Apparatus 1 generally increased with increasingly larger openings of the basket mesh. Increasing the basket agitation speed also resulted in an overall increase in the velocities, especially below in the innermost core region below the basket, where drug fragments typically reside. More importantly, the flow entering and leaving the baskets was quantified from the velocity profiles in the immediate vicinity of the baskets. It was found that the flow increased significantly with increasingly larger mesh openings, which can, in turn, promote faster dissolution of the oral solid dosage forms, thus affecting drug dissolution profiles. Hence, the selection of the basket mesh size must be carefully considered during drug product development.

The Introduction of a New Flexible In Vivo Predictive Dissolution Apparatus, GIS-Alpha (GIS-α), to Study Dissolution Profiles of BCS Class IIb Drugs, Dipyridamole and Ketoconazole.

The physiological pH changes and peristalsis activities in gastrointestinal (GI) tract have big impact on the dissolution of oral drug products, when those oral drug products include APIs with pH-dependent solubility. It is well documented that predicting the bioperformance of those oral drug products can be challenging using compendial methods. To overcome this limitation, in vivo predictive dissolution apparatuses, such as the transfer model, have been developed to predict bioperformance of oral formulation candidates and drug products. In this manuscript we utilize a new transfer-model dissolution apparatus, the gastrointestinal simulator-α (GIS-α), to characterize its behavior in terms of transfer kinetics and pH, assess its reproducibility and adaptability to mimic different transfer conditions, as well as study dissolution of ketoconazole and dipyridamole as model BCS class IIb compounds. Availability of commercially available dissolution transfer systems with similar configuration to compendial dissolution apparatus, may be helpful to simplify and standardize in vivo predictive dissolution methodologies for BCS class IIb compounds in the future.

Biorelevant dissolution testing of a weak base: Interlaboratory reproducibility and investigation of parameters controlling in vitro precipitation.

Following a previous study which aimed to determine the interlaboratory reproducibility of biorelevant dissolution testing in the USP 2 apparatus for commercial formulations of two weak acids (ibuprofen and zafirlukast), this study attempts to determine the interlaboratory reproducibility using a similar protocol for a commercially available formulation of a weak base, indinavir. Fourteen partners including twelve industrial and two academic partners participated in this study. To ensure uniformity, all partners were provided with a standardized protocol to perform (i) a single medium dissolution test in fasted state simulated gastric and intestinal fluids (FaSSGF and FaSSIF, respectively) and (ii) a two-stage dissolution experiment simulating gastrointestinal transfer. Optionally, partners could run a single-stage dissolution test in fed state simulated intestinal fluid (FeSSIF). For each dissolution test, one Crixivan® capsule (containing 400 mg indinavir as its sulfate salt) was added as dose of interest. For the single medium dissolution test in FaSSIF, all partners observed rapid release of indinavir resulting in supersaturated concentrations, followed by precipitation to equilibrium solubility. The degree and period of supersaturation varied among the participating laboratories. Average dissolution profiles in FeSSIF appeared to be highly reproducible with dissolved concentrations remaining lower than the thermodynamic solubility of indinavir in FeSSIF. For the two-stage dissolution test, most partners observed supersaturated concentrations in the intestinal compartment; two partners observed no supersaturation due to immediate precipitation. Given the fact that a high interlaboratory but low intralaboratory variability was observed when supersaturation/precipitation occurred, an undefined factor was hypothesized as a potential cause of the variability in precipitation. Hence, the impact of several experimental factors on the supersaturation and precipitation behavior of indinavir was investigated in a next step. The investigation indicated that variability is likely attributable to a combination of factors, especially, the time elapsed between sampling and dilution of the sample with the mobile phase. Therefore, when designing a test in which supersaturation and precipitation is anticipated, stringent control of the test methodology, especially regarding sampling and dilution, is needed.

Integration of Precipitation Kinetics From an In Vitro, Multicompartment Transfer System and Mechanistic Oral Absorption Modeling for Pharmacokinetic Prediction of Weakly Basic Drugs.

Solubility, dissolution, and precipitation in the gastrointestinal tract can be critical for the oral bioavailability of weakly basic drugs. To understand the dissolution and precipitation during the transfer out of the stomach into the intestine, a multicompartment transfer system was developed by modifying a conventional dissolution system. This transfer system included gastric, intestinal, sink and supersaturation, and reservoir compartments. Simulated gastric fluid and fasted state simulated intestinal fluid were used in the gastric and intestinal compartment, respectively, to mimic fasted condition. The new transfer system was evaluated based on 2 model weak bases, dipyridamole and ketoconazole. Traditional 2-stage dissolution using 250 mL of simulated gastric fluid media, followed by 250 mL of fasted state simulated intestinal fluid, was used as a reference methodology to compare dissolution and precipitation results. An in silico model was built using R software suite to simulate the in vitro time-dependent dissolution and precipitation process when formulations were tested using the transfer system. The precipitation rate estimated from the in vitro data was then used as the input for absorption and pharmacokinetic predictions using GastroPlus. The resultant simulated plasma concentration profiles were generally in good agreement with the observed clinical data, supporting the translatability of the transfer system in vitro precipitation kinetics to in vivo.

USP Apparatus 4: a Valuable In Vitro Tool to Enable Formulation Development of Long-Acting Parenteral (LAP) Nanosuspension Formulations of Poorly Water-Soluble Compounds.

Long-acting or extended release parenteral dosage forms have attracted extensive attention due to their ability to maintain therapeutic drug concentrations over long periods of time and reduce administration frequency, thus improving patient compliance. It is essential to have an in vitro release (IVR) testing method that can be used to assure product quality during routine production as well as predict and understand the in vivo performance of a formulation. The purpose of this work was to develop a discriminatory in vitro release method to guide formulation and process development of long-acting parenteral (LAP) nanosuspension formulations composed of poorly water-soluble drugs (BCS class II). Injectable nanosuspension formulations were developed to serve as test articles for method development. Several different IVR methods were evaluated for their application to the formulation screening and process development including (1) USP apparatus 2, (2) dialysis and reverse dialysis sac, and (3) continuous flow-through cell (USP apparatus 4). Preliminary data shows the promising results to support the utilization of USP 4 over more widely accepted USP 2 and dialysis methods. A combination of more representative in vivo hydrodynamics and ease of maintaining sink conditions yields the USP 4 flow-through cell method a more suitable in vitro release method for nanosuspension-based LAP formulations of poorly water-soluble compounds, such as compounds A and B.

In Silico Modeling Approach for the Evaluation of Gastrointestinal Dissolution, Supersaturation, and Precipitation of Posaconazole.

The aim of this study was to evaluate gastrointestinal (GI) dissolution, supersaturation, and precipitation of posaconazole, formulated as an acidified (pH 1.6) and neutral (pH 7.1) suspension. A physiologically based pharmacokinetic (PBPK) modeling and simulation tool was applied to simulate GI and systemic concentration-time profiles of posaconazole, which were directly compared with intraluminal and systemic data measured in humans. The Advanced Dissolution Absorption and Metabolism (ADAM) model of the Simcyp Simulator correctly simulated incomplete gastric dissolution and saturated duodenal concentrations of posaconazole in the duodenal fluids following administration of the neutral suspension. In contrast, gastric dissolution was approximately 2-fold higher after administration of the acidified suspension, which resulted in supersaturated concentrations of posaconazole upon transfer to the upper small intestine. The precipitation kinetics of posaconazole were described by two precipitation rate constants, extracted by semimechanistic modeling of a two-stage medium change in vitro dissolution test. The 2-fold difference in exposure in the duodenal compartment for the two formulations corresponded with a 2-fold difference in systemic exposure. This study demonstrated for the first time predictive in silico simulations of GI dissolution, supersaturation, and precipitation for a weakly basic compound in part informed by modeling of in vitro dissolution experiments and validated via clinical measurements in both GI fluids and plasma. Sensitivity analysis with the PBPK model indicated that the critical supersaturation ratio (CSR) and second precipitation rate constant (sPRC) are important parameters of the model. Due to the limitations of the two-stage medium change experiment the CSR was extracted directly from the clinical data. However, in vitro experiments with the BioGIT transfer system performed after completion of the in silico modeling provided an almost identical CSR to the clinical study value; this had no significant impact on the PBPK model predictions.

Validation of Dissolution Testing with Biorelevant Media: An OrBiTo Study.

Dissolution testing with biorelevant media has become widespread in the pharmaceutical industry as a means of better understanding how drugs and formulations behave in the gastrointestinal tract. Until now, however, there have been few attempts to gauge the reproducibility of results obtained with these methods. The aim of this study was to determine the interlaboratory reproducibility of biorelevant dissolution testing, using the paddle apparatus (USP 2). Thirteen industrial and three academic laboratories participated in this study. All laboratories were provided with standard protocols for running the tests: dissolution in FaSSGF to simulate release in the stomach, dissolution in a single intestinal medium, FaSSIF, to simulate release in the small intestine, and a "transfer" (two-stage) protocol to simulate the concentration profile when conditions are changed from the gastric to the intestinal environment. The test products chosen were commercially available ibuprofen tablets and zafirlukast tablets. The biorelevant dissolution tests showed a high degree of reproducibility among the participating laboratories, even though several different batches of the commercially available medium preparation powder were used. Likewise, results were almost identicalbetween the commercial biorelevant media and those produced in-house. Comparing results to previous ring studies, including those performed with USP calibrator tablets or commercially available pharmaceutical products in a single medium, the results for the biorelevant studies were highly reproducible on an interlaboratory basis. Interlaboratory reproducibility with the two-stage test was also acceptable, although the variability was somewhat greater than with the single medium tests. Biorelevant dissolution testing is highly reproducible among laboratories and can be relied upon for cross-laboratory comparisons.

Flexible, all-organic chemiresistor for detecting chemically aggressive vapors.

Chemiresistors made of thin films of single-walled carbon nanotube (CNT) bundles on cellulosics (paper and cloth) can detect aggressive oxidizing vapors such as nitrogen dioxide and chlorine at 250 and 500 ppb, respectively, at room temperature in ambient air without the aid of a vapor concentrator. Inkjet-printed films of CNTs on 100% acid-free paper are significantly more robust than dip-coated films on plastic substrates. Performance attributes include low sensor-to-sensor variation, spontaneous signal recovery, negligible baseline drift, and the ability to bend the sensors to a crease without loss of sensor performance.

Simultaneous papillary muscle avulsion and free wall rupture during acute myocardial infarction. Intra-aortic balloon pump: a bridge to survival.

Mechanical complications of acute myocardial infarction (AMI) are rare, but often fatal. Medical therapy does not provide adequate risk reduction, and surgical correction is recommended when feasible. Supplemental hemodynamic support utilizing intra-aortic counterpulsation with a balloon pump provides an improvement in morbidity and mortality when combined with a corrective surgical approach. We report a case of an elderly male with a progressive 2-week history of ischemic symptoms presenting with acute pulmonary edema, hypotension and an inferior wall ST-elevation MI. His hospital course was complicated by ischemic mitral regurgitation (MR) and cardiogenic shock, which resulted in a papillary muscle rupture/avulsion from the inferolateral myocardial wall, and a communication for blood from ventricle to pericardial space. Initial management included mechanical ventilation, pharmacologic inotropic support, percutaneous revascularization of the culprit lesion and intra-aortic balloon counterpulsation. The patient underwent further successful cardiovascular surgical correction of his incompetent mitral valve, free wall rupture and other obstructive coronary arteries, leading to discharge and survival. Mechanical complications from AMI and the role of intra-aortic balloon support are discussed.