The evolution of basal septal hypertrophy: From benign and age-related normal variant to potentially obstructive and symptomatic cardiomyopathy.

Localized thickening of the basal portion of the ventricular septum or basal septal hypertrophy (BSH) has been identified both at autopsy and by imaging studies for decades; despite numerous investigations, there is no consensus on the significance of this finding and a remarkable lack of consistency in terminology. This paper summarizes the scientific literature on the topic, focusing on recent echocardiographic findings. A case description illustrating some of the complex issues involved in measurement and diagnosis and differentiation from sigmoidal hypertrophic cardiomyopathy (HCM) is presented. Criteria are proposed for diagnosing pathologic BSH which include the following: (1) Exertional symptoms compatible with left ventricular outflow tract obstruction (LVOTO) such as dyspnea, near-syncope, and chest discomfort; (2) Documented LVOTO gradient demonstrated at peak bicycle or post-treadmill exercise >30 mm Hg; and (3) Symptomatic improvement with ß-blocker (or other negative inotropic) therapy (preferably accompanied by documentation of reduction of exercise-induced LVOT).

Thin-Film Carbon Nanofuses for Permanent Data Storage.

In this study, we have fabricated nanofuses from thin-film, arc-deposited carbon for use in permanent data storage. Thin-film carbon fuses have fewer fabrication barriers and retain the required resistivity and structural stability to act as a data-storage medium. Carbon thin films were characterized for their electrical, microstructural, and chemical bonding properties. Annealing these films in an argon environment at 400 °C reduced the resistivity from about 4 × 10-2 Ω cm as deposited to about 5 × 10-4 Ω cm, allowing a lower blowing voltage. Nanofuses with widths ranging from 200 to 60 nm were fabricated and tested. They blow with voltages between 2 and 5.5 V, and the nanofuses remain stable in both "1" and "0" states under a constantly applied read voltage of 1 V for over 90 h.

Electrically conductive gold- and copper-metallized DNA origami nanostructures.

This work demonstrates the use of a circuit-like DNA origami structure as a template to fabricate conductive gold and copper nanostructures on Si surfaces. We improved over previous results by using multiple Pd seeding steps to increase seed uniformity and density. Our process has also been characterized through atomic force microscopy, particle size distribution analysis, and scanning electron microscopy. We found that four successive Pd seeding steps yielded the best results for electroless metal plating on DNA origami. Electrical resistance measurements were done on both Au- and Cu-metallized nanostructures, with each showing ohmic behavior. Gold-plated DNA origami structures made under optimal conditions had an average resistivity of 7.0 × 10(-5) Ω·m, whereas copper-metallized structures had a resistivity as low as 3.6 × 10(-4) Ω·m. Importantly, this is the first demonstration of electrically conductive Cu nanostructures fabricated on either DNA or DNA origami templates. Although resistivities for both gold and copper samples were larger than those of the bulk metal, these metal nanostructures have the potential for use in electrically connecting small structures. In addition, these metallized objects might find use in surface-enhanced Raman scattering experiments.

Dual patterning of a poly(acrylic acid) layer by electron-beam and block copolymer lithographies.

We show the controllable patterning of palladium nanoparticles in both one and two dimensions using electron-beam lithography and reactive ion etching of a thin film of poly(acrylic acid) (PAA). After the initial patterning of the PAA, a monolayer of polystyrene-b-poly-2-vinylpyridine micelles is spun cast onto the surface. A short reactive ion etch is then used to transfer the micelle pattern into the patterned poly(acrylic acid). Finally, PdCl2 is loaded from solution into the patterned poly(acrylic acid) features, and a reactive-ion etching process is used to remove the remaining polymer and form Pd nanoparticles. This method yields location-controlled patches of nanoparticles, including single- and double-file lines and nanoparticle pairs. A locational accuracy of 9 nm or less in one direction was achieved by optimizing the size of the PAA features.

DNA origami metallized site specifically to form electrically conductive nanowires.

DNA origami is a promising tool for use as a template in the design and fabrication of nanoscale structures. The ability to engineer selected staple strands on a DNA origami structure provides a high density of addressable locations across the structure. Here we report a method using site-specific attachment of gold nanoparticles to modified staple strands and subsequent metallization to fabricate conductive wires from DNA origami templates. We have modified DNA origami structures by lengthening each staple strand in select regions with a 10-base nucleotide sequence and have attached DNA-modified gold nanoparticles to the lengthened staple strands via complementary base-pairing. The high density of extended staple strands allowed the gold nanoparticles to pack tightly in the modified regions of the DNA origami, where the measured median gap size between neighboring particles was 4.1 nm. Gold metallization processes were optimized so that the attached gold nanoparticles grew until gaps between particles were filled and uniform continuous nanowires were formed. Finally, electron beam lithography was used to pattern electrodes in order to measure the electrical conductivity of metallized DNA origami, which showed an average resistance of 2.4 kΩ per metallized structure.

Chemical alignment of DNA origami to block copolymer patterned arrays of 5 nm gold nanoparticles.

We have used block copolymer patterned arrays of 5 nm gold nanoparticles (AuNPs) for chemically aligned surface attachment of DNA origami. Addition of single-stranded DNA-thiol to AuNPs allowed a base paired attachment of sticky end modified DNA origami. Results indicate a stable, selective attachment between the DNA origami and ssDNA modified AuNPs. Yield data showed 74% of AuNP binding sites forming an attachment with a DNA origami rectangle, and control surfaces showed less than 0.5% nonspecific adsorption.

Multiple mechanisms of rhabdom shedding in the lateral eye of Limulus polyphemus.

Rhabdom shedding in horseshoe crab lateral eye photoreceptors was studied with anti-opsin and anti-arrestin immunocytochemistry. Two, possibly three, distinct shedding mechanisms were revealed in animals maintained in natural lighting. Transient rhabdom shedding, triggered by dawn, is a brief, synchronous event that removes up to 10% of the rhabdom membrane. Whorls of rhabdomeral membrane break into vesicles and form compact multivesicular bodies. These debris particles are immunoreactive for opsin and are of a relatively uniform size, averaging approximately 2 microm(2) in area. Transient shedding requires that input from circadian efferent fibers to the retina precedes the light trigger, and cutting the optic nerve blocks efferent input and transient shedding. Light-driven rhabdom shedding is a progressive process. Rhabdomeral membrane is removed by coated vesicles that accumulate into loosely packed multivesicular bodies. These debris particles label with antibodies directed against opsin, arrestin, and adaptin, and they have a large distribution of sizes, averaging almost 6 microm(2) in area and ranging up to 25 microm(2) or more. The amount of rhabdomeral membrane removed by light-driven shedding has seasonal variation and depends on latitude. Light-driven shedding does not require circadian efferent input. A possible third shedding mechanism, light-independent shedding, is observed when transient shedding is blocked either by 48 hours of darkness or by cutting the optic nerve. Small particles, averaging 1.8 microm(2) in area, exhibiting opsin but not arrestin immunoreactivity can then be found in the cytoplasm surrounding the rhabdom. The nature of light-independent shedding is not yet clear.