Mechanistic study of the stabilization of dentin-bonded restorative interfaces via collagen reinforcement by multi-acrylamides.

Hydrolytically and enzymatically-stable multi-acrylamides have been proposed to increase the long-term durability of dental adhesive interfaces as alternatives to methacrylates. The aim of this study was to investigate the mechanical and biochemical properties of experimental adhesives containing multi-functional acrylamides concerning collagen reinforcement and metalloproteinases (MMP) activity. Multi-functional acrylamides, TMAAEA (Tris[(2-methylaminoacryl) ethylamine) and DEBAAP (N,N-Diethyl-1,3-bis(acrylamido) propane), along with the commercially available DMAM (N,N-dimethylacrylamide) (monofunctional acrylamide) and HEMA (2-Hydroxyethyl methacrylate) (monofunctional methacrylate - control) were tested for stability against enzymatic hydrolysis by cholesterol esterase/pseudocholinesterase (PC/PCE) solutions for up to 30 days. Collagen-derived substrate and gelatin zymography were performed to examine the effect of the compounds on the biological activity of human recombinant and dentin-extracted gelatinases MMP-2 and MMP-9. In situ zymography was carried out by fluorescent collagen degradation combined with confocal microscopy analysis. Hydroxyproline content was measured in collagen derived from dentin extracts though reaction with Ehrlich's reagent p-dimethylaminobenzaldehyde (DMAB), generating a stable chromophore measured at 550 nm. Storage shear modulus of demineralized dentin discs treated with the tested compounds was measured by oscillatory rheometry, in order to investigate potential collagen reinforcement. FT-IR was performed to determine qualitative differences in collagen based on observed changes in amide bands. The results were analyzed by ANOVA/Tukey's test (α = 0.05). Multi-acrylamides survived 30 days of incubation in cholinesterase/pseudo-cholinesterase (PC/PCE) solutions, while HEMA showed approximately 70 % overall degradation. Incubation with multi-acrylamides reduced collagen degradation as evidenced by the reduced hydroxyproline levels and by the 30 % increase inshear storage modulus. Biochemical and zymography assays showed no noticeable inhibition of recombinant and extracted MMPs enzymatic activity. The infra-red spectroscopy results for multi-functional acrylamides treated samples demonstrated shifts of the amide II bonds and marked increase in intensity of the bands 1200 cm-1, which may indicate partial collagen denaturation and some degree of cross-linking of the compounds with collagen, respectively. The multi-acrylamides exhibited not only comparable mechanical properties but also demonstrated significantly enhanced biochemical stability when compared to the widely used methacrylate control. Clinical relevance: These findings highlight the potential of multi-acrylamides to increase the bonding stability to tissues and, ultimately, contribute to the longevity of dental restorations.

Triacrylamide-Based Adhesives Stabilize Bonds in Physiologic Conditions.

In this study, an acrylamide-based adhesive was combined with a thiourethane-based composite to improve bond stability and reduce polymerization stress, respectively, of simulated composite restorations. The stability testing was conducted under physiologic conditions, combining mechanical and bacterial challenges. Urethane dimethacrylate was combined with a newly synthesized triacrylamide (TMAAEA) or HEMA (2-hydroxyethyl-methacrylate; control) to produce a 2-step total-etch adhesive system. Methacrylate-based composites (70 wt% silanized filler) were formulated, containing thiourethane oligomers at 0 (control) or 20 wt%. Standardized preparations in human third molars were restored; then, epoxy replicas were obtained from the occlusal surfaces before and after 7-d storage in water or with Streptococcus mutans biofilm, which was tested after storage in an incubator (static) or the bioreactor (mechanical challenge). Images were obtained from the replicas (scanning electron microscopy) and cross sections of the samples (confocal laser scanning microscopy) and then analyzed to obtain measurements of gap, bacterial infiltration, and demineralization. Microtensile bond strength of specimens stored in water or biofilm was assessed in 1-mm2 stick specimens. Data were analyzed with analysis of variance and Tukey's test (α = 0.05). HEMA-based materials had greater initial gap measurements, indicating more efficient bonding for the acrylamide materials. When tested in water, the triacrylamide-based adhesive had smaller gaps in the incubator or bioreactor. In the presence of biofilm, there was less difference among materials, but the acrylamide/thiourethane combination led to statistically lower gap formation in the bioreactor. HEMA and TMAAEA-based adhesives produced statistically similar microtensile bond strengths after being stored in water for 7 d, but after the same period with biofilm-challenged specimens, the TMAAEA-based adhesives were the only ones to retain the initial bond strength values. The use of a stable multiacrylamide-based adhesive led to the preservation of the resin-dentin bonded interface after a physiologically relevant challenge. Future studies will include a multispecies biofilm model.

Probing stress relaxation behavior in glassy methacrylate networks containing thio-carbamate additives.

The incorporation of thiourethane prepolymer (TU) into either the organic phase or as a surface treatment for filler particles in composites reduces polymerization stress and improves fracture toughness. The aim of this study was to gain insight into the influence of the inclusion of thiourethanes on the resulting network of methacrylate-based materials polymerized via free-radical mechanisms. Dynamic mechanical analysis was used to elucidate network parameters and potential stress relaxation behavior of these networks. TU oligomers were synthesized using a combination of trimethylol-tris-3-mercaptopropionate and dicyclohexylmethane 4,4'-diisocyanate and added into composite formulations at 20 wt% replacing part of the organic matrix and/or as TU-silanes used to functionalize filler particles (TU-matrix, TU-Sil or TU-matrix/sil). Materials not containing any form of TU were used as the control (in those cases, 3-(trimethoxysilyl)propyl methacrylate was used as the silane agent). Filler was added at 50 wt%. Degree of conversion was evaluated by near-IR spectroscopy, mechanical properties by 3-point bending and rotational rheometry. Dynamic mechanical analysis was used to obtain network parameters (glass transition temperature (Tg), storage modulus, cross-link density, and breadth of tan delta a proxy for network homogeneity - temperature sweep experiments) and to evaluate the potential for network relaxation (stress relaxation). TU-containing formulations showed 10% higher DC than the control. The time to reach storage/loss modulus crossover in the rheometer experiments was significantly longer for TU-matrix and TU-matrix/sil in comparison with the control (21.6, 27.9, and 5.1 s, respectively). TU-matrix and TU-matrix/sil presented significant lower Tg than the control (151.5, 153.8, and 161.3 °C, respectively). There were no statistical differences among the groups in terms of shear modulus, cross-link density, breadth of tan delta, flexural strength/modulus, and toughness. For at least one group (TU-matrix/sil), the relaxation time was four times faster than for the control at 105 °C. The addition of TU additives into dental polymers resulted in a stark reduction in the stress relaxation time. This behavior, in tandem with the network characterization and mechanical properties seems to indicate the TU networks undergo a variety of reversible associative and dissociative chemical reactions which facilitate enhanced stress relief.

Trimers Conjugated to Fibrin Hydrogels Promote Salivary Gland Function.

New strategies for tissue engineering have great potential for restoring and revitalizing impaired tissues and organs, including the use of smart hydrogels that can be modified to enhance organization and functionality of the salivary glands. For instance, monomers of laminin-111 peptides chemically conjugated to fibrin hydrogel (L1pM-FH) promote cell cluster formation in vitro and salivary gland regeneration in vivo when compared with fibrin hydrogel (FH) alone; however, L1pM-FH produce only weak expression of acinar differentiation markers in vivo (e.g., aquaporin-5 and transmembrane protein 16). Since previous studies demonstrated that a greater impact can be achieved when trimeric forms were used as compared with monomeric or dimeric forms, we investigated the extent to which trimers of laminin-111 chemically conjugated to FH (L1pT-FH) can increase the expression of acinar differentiation markers and elevate saliva secretion. In vitro studies using Par-C10 acinar cells demonstrated that when compared with L1pM-FH, L1pT-FH induced similar levels of acinar-like cell clustering, polarization, lumen formation, and calcium signaling. To assess the performance of the trimeric complex in vivo, we compared the ability of L1pM-FH and L1pT-FH to increase acinar differentiation markers and restore saliva flow rate in a salivary gland wound model of C57BL/6 mice. Our results show that L1pT-FH applied to wounded mice significantly improved the expression of the acinar differentiation markers and saliva secretion when compared with the monomeric form. Together, these positive effects of L1pT-FH warrant its future testing in additional models of hyposalivation with the ultimate goal of applying this technology in humans.

Thiourethane filler functionalization for dental resin composites: Concentration-dependent effects on toughening, stress reduction and depth of cure.

OBJECTIVES: The aim of this study was to modify the surface of fillers used in dental composites by the synthesis of two novel thiourethane oligomeric silanes, used to functionalize the silica-containing inorganic particles. Several thiourethane silane concentrations were tested during the silanization process to systematically assess the effect of silane coverage on experimental composite conversion, polymerization stress and fracture toughness. MATERIALS AND METHODS: Two different thiourethane silanes were synthesized based either on 1,6-hexanediol-diissocynate (HDDI), or 1,3-bis(1-isocyanato-1-methylethyl) benzene (BDI). Conventional 3-(Trimethoxysilyl)propyl methacrylate was used as the control. Glass fillers were silanized with 1, 2 or 4 wt% of each thiourethane silane, then evaluated by thermogravimetrical analysis. Photopolymerizable resin composites were prepared with Bis-GMA/UDMA/TEGDMA and 50 wt% silanized glass filler. Polymerization kinetics and degree of conversion were tested using Near-IR. Bioman was used to test polymerization stress. Data were analyzed with two-way ANOVA/Tukey's test (α = 5%). RESULTS: The mass of silane coupled to the filler increased with the concentrations of thiourethane in the silanizing solution, as expected. Thiourethane-containing groups exhibited significantly higher degree of conversion compared to control groups, except for BDI 4%. HDDI 4%, BDI 2% and BDI 4% showed significantly lower polymerization stress than control groups. HDDI 4% exhibited significantly higher fracture toughness. CONCLUSIONS AND CLINICAL SIGNIFICANCE: Novel filler functionalization with thiourethane silanes may be a promising alternative for improving dental composites properties by significantly increasing the degree of conversion, fracture toughness and reducing the polymerization stress.

Effects of systematically varied thiourethane-functionalized filler concentration on polymerization behavior and relevant clinical properties of dental composites.

Introduction of thiourethane (TU) oligomer to resin-based dental restorative materials reduces stress and improves fracture toughness without compromising conversion. Localization of TU at the resin-filler interface via silanization procedures may lead to more substantial stress reduction and clinical property enhancements. The objective of this study was to evaluate composite properties as a function of TU-functionalized filler concentration. TU oligomers were synthesized using click-chemistry techniques and subsequently silanized to barium glass filler. Resin-based composites were formulated using varying ratios of TU-functionalized filler and conventional methacrylate-silanized barium filler. Material property testing included thermogravimetric analysis, real-time polymerization kinetics and depth of cure, polymerization stress, stress relaxation and fracture toughness. Clinical property testing included water sorption/solubility, composite paste viscosity, and gloss and surface roughness measured before and after subjecting the samples to 6 h of continuous tooth brushing in a custom-built apparatus using a toothpaste/water mixture. Increasing TU-filler in the composite resulted in as much as a 78% reduction in stress, coupled with an increase in fracture toughness. Conversion was similar for all groups. After simulated tooth brushing, gloss reduction was lower for TU-containing composites and surface roughness was less than or equal to the control.

In vitro performance of 2-step, total etch adhesives modified by thiourethane additives.

OBJECTIVES: Thio-urethane oligomeric additives have been shown to improve the mechanical properties of dental composites and resin cements. To try to harness those same properties in dental adhesives, in this study, these oligomers (TU) were added to the matrix and/or as filler functionalization of experimental adhesives, and the effects on conversion and mechanical properties were analyzed. METHODS: BisGMA and HEMA (60/40 wt%) were used as the monomer matrix, made polymerizable by the addition of 0.2 wt% 2,2-dimethoxy-2- phenylacetophenone. 2,6-di-tert-butyl-4-methylphenol was added at 0.5 wt% as the inhibitor. This material was used as the unfilled control (BH). TU oligomers were added at 20 wt % to the matrix (BH+20%TU, unfilled) and/or used as filler functionalization (TF, 10 wt%). Fillers functionalized with methacrylate (MF, 10 wt%) served as the control. The experimental adhesives groups containing fillers were: BH+10%MF; BH+10%TF; BH+20%TU+10%MF; BH+20%TU+10%TF. Flexural properties were tested in three-point bending (wet and dry). Polymerization kinetics was followed in real-time in near-IR. Water Sorption/Solubility (WS/SL, ISO 4049) and Viscosity (rotational rheometry) were also evaluated. For Microtensile bond strength 40 vol% ethanol was added to adhesives, which was applied onto sound dentin from third human molars. The data were analyzed with one-way ANOVA and Tukey post-hoc test, and test t for the comparison between storage time of the microtensile bond strength test (alpha = 0.05). RESULTS: There was no significant difference between groups when yield strength (YS) and flexural modulus (FM) were evaluated in dry conditions. After water storage, all the groups containing TU in the matrix showed statistically lower YS/FM values. This was true in spite of the statistically higher conversion for those same groups. The maximum rate of polymerization (Rpmax) was higher for BH+10%TF and no significant difference was found for the groups BH and BH+10% MF. The lowest Rpmax values were found for BH+20%TU+10%TF and BH+20%TU. BH+20%TU+10%TF showed the highest viscosity values followed by BH+20%TU+10%MF and BH+20%TU, with statistically significant difference between them. For the microtensile bond strength test at 24h (p = 0.13) and 6 months (p = 0.11) and WS/SL (p > 0.05), no significant difference was found among groups. The storage time (24 h and 6 months) did not affect the microtensile bond strength results. CONCLUSION: In spite of improving the conversion, the addition of TU in the matrix reduced the mechanical properties of the adhesives tested after water storage. This did not affect the bond strength at 24 h or 6 months.

Interaction between the Oral Microbiome and Dental Composite Biomaterials: Where We Are and Where We Should Go.

Dental composites are routinely placed as part of tooth restoration procedures. The integrity of the restoration is constantly challenged by the metabolic activities of the oral microbiome. This activity directly contributes to a less-than-desirable half-life for the dental composite formulations currently in use. Therefore, many new antimicrobial dental composites are being developed to counteract the microbial challenge. To ensure that these materials will resist microbiome-derived degradation, the model systems used for testing antimicrobial activities should be relevant to the in vivo environment. Here, we summarize the key steps in oral microbial colonization that should be considered in clinically relevant model systems. Oral microbial colonization is a clearly defined developmental process that starts with the formation of the acquired salivary pellicle on the tooth surface, a conditioned film that provides the critical attachment sites for the initial colonizers. Further development includes the integration of additional species and the formation of a diverse, polymicrobial mature biofilm. Biofilm development is discussed in the context of dental composites, and recent research is highlighted regarding the effect of antimicrobial composites on the composition of the oral microbiome. Future challenges are addressed, including the potential of antimicrobial resistance development and how this could be counteracted by detailed studies of microbiome composition and gene expression on dental composites. Ultimately, progress in this area will require interdisciplinary approaches to effectively mitigate the inevitable challenges that arise as new experimental bioactive composites are evaluated for potential clinical efficacy. Success in this area could have the added benefit of inspiring other fields in medically relevant materials research, since microbial colonization of medical implants and devices is a ubiquitous problem in the field.

Effect of different composite modulation protocols on the conversion and polymerization stress profile of bulk-filled resin restorations.

OBJECTIVE: The aim of this in vitro study was to test the effect of different composite modulation protocols (pre-heating, light-curing time and oligomer addition) for bulk filling techniques on resin polymerization stress, intra-pulpal temperature change and degree of conversion. METHODS: Class I cavities (4mm depth×5mm diameter) were prepared in 48 extracted third molars and divided in 6 groups. Restorations were completed with a single increment, according to the following groups: (1) Filtek Z250XT (room temperature - activated for 20s); (2) Filtek Z250XT (at room temperature - activated for 40s); (3) Filtek Z250XT (pre-heated at 68°C - activated for 20s); (4) Filtek Z250XT (pre-heated at 68°C - activated for 40s); (5) Filtek BulkFill (at room temperature - activated for 20s); (6) Filtek Z250XT (modified by the addition of a thio-urethane oligomer at room temperature - activated for 40s). Acoustic emission test was used as a real-time polymerization stress (PS) assessment. The intra-pulpal temperature change was recorded with a thermocouple and bottom/top degree of conversion (DC) measured by Raman spectroscopy. Data were analyzed with one-way ANOVA/Tukey's test (α=5%). RESULTS: Pre-heating the resin composite did not influence the intra-pulpal temperature (p=0.077). The thio-urethane-containing composite exhibited significantly less PS, due to a lower number of acoustic events. Groups with pre-heated composites did not result in significantly different PS. Filtek BulkFill and the thio-urethane experimental composite presented significantly higher DC. SIGNIFICANCE: Resin composite pre-heating was not able to reduce polymerization stress in direct restorations. However, thio-urethane addition to a resin composite could reduce the polymerization stress while improving the DC.

Effect of the photoinitiator system on the polymerization of secondary methacrylamides of systematically varied structure for dental adhesive applications.

OBJECTIVE: The aim of this study was to investigate the influence of the photoinitiator system on the polymerization kinetics of methacrylamide-based monomers as alternatives to methacrylates in adhesives dental-based materials. METHODS: In total, 16 groups were tested. Monofunctional monomers (2-hydroxyethyl methacrylate) - HEMA; (2-hydroxy-1-ethyl methacrylate) -2EMATE, (2-hydroxyethyl methacrylamide) - HEMAM; and (N-(1-hydroxybutan-2-yl) methacrylamide) -2EM; were combined with bifunctional monomers containing the same polymerizing moieties as the monofunctional counterparts (HEMA-BDI; 2EMATE-BDI; HEMAM-BDI; and 2EM-BDI) at 50/50 M ratios. BHT was used as inhibitor (0.1 wt%) and the photoinitiators used were: CQ + EDMAB (0.2/0.8), BAPO (0.2), IVOCERIN (0.2), and DMPA (0.2), in wt%. The polymerization kinetics were monitored using Near-IR spectroscopy (∼6165 cm-1) in real-time while the specimens were photoactivated with a mercury arc lamp (Acticure 2; 320-500 nm, 300 mW/cm2) for 5 min, and maximum rate of polymerization (Rpmax, in %.s-̄1), degree of conversion at Rpmax (DC@Rpmax, in %), and the final degree of conversion (Final DC, in %) were calculated (n = 3). Initial viscosity was measured with an oscillating rheometer (n = 3). Data were analyzed using Two-way ANOVA for the polymerization kinetics and one-way ANOVA for the viscosity. Multiple comparisons were made using the Tukey's test (∝ = 0.05). RESULTS: There was statistically significant interaction between monomer and photoinitiator (p < 0.001). For the methacrylates groups, the highest Rpmax was observed for HEMA + DMPA and 2EMATE + BAPO. For methacrylamides groups, the highest Rpmax were observed for HEMAM and 2EM, both with DMPA. Final DC was higher for the methacrylate groups, in comparison with methacrylamide groups, independent of the photoinitiators. However, for the methacrylamide groups, the association with BAPO led to the lowest values of DC. In terms of DC@Rpmax, methacrylate-based systems showed significantly higher values than methacrylamide formulations. DMPA and Ivocerin led to higher values than CQ/EDMAB and BAPO in methacrylamide-based compounds. BAPO systems showed de lowest values for both HEMA and HEMAM formulations. For the viscosity (Pa.s), only 2EM had higher values (1.60 ± 0.15) in comparison with all monomers. In conclusion, polymerization kinetics was affected by the photoinitiators for both monomers. Viscosity was significantly increased with the use of secondary methacrylamide. SIGNIFICANCE: this work demonstrated the feasibility of using newly-synthesized methacrylamide monomers in conjunction with a series of initiator systems already used in commercial materials.

Effect of the addition of thiourethane oligomers on the solâ¿¿gel composition of BisGMA/TEGDMA polymer networks.

OBJECTIVES: Thiourethane oligomers have been shown to increase the fracture toughness and reduce the polymerization stress of methacrylate-based materials. However, network formation has not been elucidated in these materials yet. The aim of this study was to evaluate how the addition of a thiourethane oligomer (TU) influences the sol/gel composition and network structure of methacrylate-based materials using dynamic mechanical analysis and extraction methods. MATERIALS AND METHODS: BisGMA/TEGDMA at systematically varied mass ratios (20/80 to 80/20wt%) were mixed with pre-polymerized thiourethane oligomers at 0 (control) or 20wt%, synthesized by combining pentaerythritol tetra-3-mercaptopropionate with dicyclohexylmethane 4,4⿲-Diisocyanate, at 1:2 isocyanate:thiol. 0.1wt% of 2,2-Dimethoxy-2-phenylacetophenone was added as the photoinitiator and 0.3wt% of 2,6-di-tert-butyl-4-methylphenol was added as a free radical inhibitor. Disk specimens (0.8ÿ10mm in diameter, n=3) were photoactivated at 270mW/ (320â¿¿500nm) for 1min. The degree of conversion (DC) was measured in near-IR (Ë¿6165cmâ¿¿1). Specimens were immersed in two different solvents (water for 7 days or dicholoromethane for 48h). Water sorption (WS) and solubility (SL) were obtained according to ISO 4049. The leachates for both solutions were analyzed with 1H-NMR (400MHz, CDCL3). Bar specimens (1ÿ3ÿ25mm, photocured and then post-processed at 180°C for 8h to DC>95%) were subjected to dynamic mechanical analysis (â¿¿30 to 230°C) to obtain glass transition temperature (Tg), tan delta curves and crosslinking density (ν). Data was analyzed with two-way ANOVA/Tukeyâ¿¿s test (95%). RESULTS: In general, the presence of TU increased the overall conversion. The WS was similar for all groups, but the SL decreased by 2-fold with the addition of the TU oligomer for all compositions, except BisGMA/TEGDMA 80/20. The BisGMA concentration of the leachates increased with increasing BisGMA in the initial mixture, and with the presence of thiourethane. This compositional drift of the gel with the presence of TU was attributed to the preferential dissolution of TEGDMA into the TU network. Tg and ν decreased with the addition of TU, as expected. The addition of TU produced more homogeneous networks, as evidenced by narrower breadth of the tan delta curve. CONCLUSION: The addition of TU affected the composition of the sol/gel in crosslinked networks, which were more homogeneous and presented 2-fold less potentially toxic leachates than the methacrylate controls. CLINICAL SIGNIFICANCE: The addition of TU may produce less cytotoxic materials based on the increased conversion and reduced amount of unreacted extractables from its network after water storage.

New Resins for Dental Composites.

Restorative composites have evolved significantly since they were first introduced in the early 1960s, with most of the development concentrating on the filler technology. This has led to improved mechanical properties, notably wear resistance, and has expanded the use of composites to larger posterior restorations. On the organic matrix side, concerns over the polymerization stress and the potential damage to the bonded interface have dominated research in the past 20 y, with many "low-shrinkage" composites being launched commercially. The lack of clinical correlation between the use of these materials and improved restoration outcomes has shifted the focus more recently to improving materials' resistance to degradation in the oral environment, caused by aqueous solvents and salivary enzymes, as well as biofilm development. Antimicrobial and ester-free monomers have been developed in the recent past, and evidence is mounting for their potential benefit. This article reviews literature on the newest materials currently on the market and provides an outlook for the future developments needed to improve restoration longevity past the average 10 y.

Clinical/Photographic/Scanning Electron Microscopy Analysis of Pit and Fissure Sealants After 22 Years: A Case Series.

Pit and fissure sealant is a clinical technique adopted to prevent caries lesion development. Ionomeric and/or resin-based materials are commonly used for this purpose. This article presents a case series of sealed teeth with 22-year follow-up evaluated by clinical, photographic, and microscopic analysis. In 1992, sixteen patients (9-14 years of age) had at least three teeth sealed with one of the following materials: resin-modified glass ionomer cement (RMGIC, Vitrebond or Fuji II LC) or polyacid-modified resin composite (PMRC, VariGlass VLC), totaling 86 sealed permanent teeth. After 22 years, 10 patients were recalled, representing 41 teeth. The retention of sealants was assessed by three methods: clinical analysis by visual inspection; photography; and scanning electron microscope (SEM) images and classified as retained (pits and fissures filled by sealant material); partially retained (pits and fissures partially filled by sealant material); or totally lost (no material was found in pits and fissures). The SEM images provided a higher number of retained sealants when compared with the clinical and photographic evaluations. Also, no totally lost scores were found with SEM analysis, regardless of the sealing material. No caries lesions were found. A fully or partially retained sealant in pits and fissures was capable of preventing caries lesions after 22 years within the patient pool analyzed.

Effect of Insufficient Light Exposure on Polymerization Kinetics of Conventional and Self-adhesive Dual-cure Resin Cements.

OBJECTIVES: The purpose of this study was to investigate the influence of insufficient light exposure on the polymerization of conventional and self-adhesive dual-cure resin cements under ceramic restorations. METHODS: Two conventional dual-cure resin cements (Rely-X ARC, Duolink) and two self-adhesive resin cements (Rely-X U200, Maxcem Elite) were polymerized under different curing modes (dual-cure or self-cure), curing times (20 and 120 seconds), and thickness of a ceramic overlay (2 and 4 mm). Polymerization kinetics was measured by Fourier transform infrared spectroscopy for the initial 10 minutes and after 24 hours. Data were analyzed using mixed model analysis of variance (ANOVA), one-way ANOVA/Student-Newman-Keuls post hoc test, and paired t-test (α=0.05). RESULTS: When light-curing time was set to 20 seconds, the presence of the ceramic block significantly affected the degree of conversion (DC) of all resin cements. Especially, the DC of the groups with 20 seconds of light-curing time under 4 mm of ceramic thickness was even lower than that of the self-cured groups at 24 hours after polymerization (p<0.05). However, when light-curing time was set to 120 seconds, a similar DC compared with the group with direct light exposure (p>0.05) was achieved in all dual-cure groups except Maxcem Elite, at 24 hours after polymerization. CONCLUSIONS: For both conventional and self-adhesive dual-cure resin cements, insufficient light exposure (20 seconds of light-curing time) through thick ceramic restoration (4 mm thick) resulted in a DC even lower than that of self-curing alone.

Thio-urethanes improve properties of dual-cured composite cements.

This study aims at modifying dual-cure composite cements by adding thio-urethane oligomers to improve mechanical properties, especially fracture toughness, and reduce polymerization stress. Thiol-functionalized oligomers were synthesized by combining 1,3-bis(1-isocyanato-1-methylethyl)benzene with trimethylol-tris-3-mercaptopropionate, at 1:2 isocyanate:thiol. Oligomer was added at 0, 10 or 20 wt% to BisGMA-UDMA-TEGDMA (5:3:2, with 25 wt% silanated inorganic fillers) or to one commercial composite cement (Relyx Ultimate, 3M Espe). Near-IR was used to measure methacrylate conversion after photoactivation (700 mW/cm(2) × 60s) and after 72 h. Flexural strength and modulus, toughness, and fracture toughness were evaluated in three-point bending. Polymerization stress was measured with the Bioman. The microtensile bond strength of an indirect composite and a glass ceramic to dentin was also evaluated. Results were analyzed with analysis of variance and Tukey's test (α = 0.05). For BisGMA-UDMA-TEGDMA cements, conversion values were not affected by the addition of thio-urethanes. Flexural strength/modulus increased significantly for both oligomer concentrations, with a 3-fold increase in toughness at 20 wt%. Fracture toughness increased over 2-fold for the thio-urethane modified groups. Contraction stress was reduced by 40% to 50% with the addition of thio-urethanes. The addition of thio-urethane to the commercial cement led to similar flexural strength, toughness, and conversion at 72h compared to the control. Flexural modulus decreased for the 20 wt% group, due to the dilution of the overall filler volume, which also led to decreased stress. However, fracture toughness increased by up to 50%. The microtensile bond strength increased for the experimental composite cement with 20 wt% thio-urethane bonding for both an indirect composite and a glass ceramic. Novel dual-cured composite cements containing thio-urethanes showed increased toughness, fracture toughness and bond strength to dentin while demonstrating reduced contraction stress. All of these benefits are derived without compromising the methacrylate conversion of the resin component. The modification does not require changing the operatory technique.

Mapping camphorquinone consumption, conversion and mechanical properties in methacrylates with systematically varied CQ/amine compositions.

OBJECTIVES: To evaluate conversion, bulk mechanical properties and camphorquinone (CQ) consumption in methacrylate resins, comprising a range of overall initiator concentrations and CQ/amine ratios. METHODS: BisGMA (Bisphenol-A glycidyl dimethacrylate), TEGDMA (triethyleneglycol dimethacrylate) and UDMA (urethane dimethacrylate) were mixed at a 1:1:1 molar ratio. CQ was used as the visible light photosensitizer, in combination with EDMAB (Ethyl p-dimethylamino benzoate), at 3:1, 2:1, 1:1, 1:2 and 1:3 weight ratios, at 0.5, 1.0, 1.5, 2.0 and 3.0 wt% overall initiator concentration. Butylhydroxytoluene was added at 0.05 wt% as an inhibitor. Unfilled resins were photoactivated with a dental light source (VIP Jr, Bisco) for 60 s at 600 mW/cm(2). Flexural strength/modulus were assessed in 2×1×10 mm bars, tested in three-point bending. Degree of conversion was assessed at the bottom of the same specimens using FT-RAMAN. CQ consumption was measured using a UV-vis spectrometer. Data were analyzed with two-way ANOVA/Tukey test (α=5%). RESULTS: Lower conversion and inferior mechanical properties were observed with lower overall initiator concentrations and higher amine/CQ ratios. The lowest overall initiator concentration (0.5%) presented the statistically lowest conversion/properties results, except for the 1:3 amine/CQ ratio. For overall concentrations equal or greater to 1.5%, the amine/CQ ratio did not influence conversion or mechanical properties. CQ consumption was less efficient for the highest overall initiator concentrations and lower amine/CQ ratios. CLINICAL RELEVANCE: Above 1.5 wt% overall initiator concentration, the conversion and general mechanical properties were independent of the initiator concentration. Therefore, there seems to be no benefit to increasing the initiator concentration above that level. At higher camphorquinone concentrations, light transmission and photosensitizer consumption becomes impaired, which could lead to decreased depth of cure and yellowing of the restoration.

Improved dental adhesive formulations based on reactive nanogel additives.

Current challenges in adhesive dentistry include over-hydrophilic bonding formulations, which facilitate water percolation through the hybrid layer and result in unreliable bonded interfaces. This study introduces nanogel-modified adhesives as a way to control the material's hydrophobic character without changing the basic monomer formulation (keeping water-chasing capacity and operatory techniques unaltered). Nanogel additives of varied hydrophobicity were synthesized in solution, rendering 10- to 100-nm-sized particles. A model BisGMA/HEMA solvated adhesive was prepared (control), to which reactive nanogels were added. The increase in adhesive viscosity did not impair solvent removal by air-thinning. The degree of conversion in the adhesive was similar between control and nanogel-modified materials, while the bulk dry and, particularly, the wet mechanical properties were significantly improved through nanogel-based network reinforcement and reduced water solubility. As preliminary validation of this approach, short-term micro-tensile bond strengths to acid-etched and primed dentin were significantly enhanced by nanogel inclusion in the adhesive resins.

Do low-shrink composites reduce polymerization shrinkage effects?

Progress in polymer science has led to continuous reduction of polymerization shrinkage, exemplified by a new generation of "low-shrink composites". The common inference that shrinkage stress effects will be reduced in teeth restored with such restoratives with lower shrinkage was tested in extracted human premolars. Mesio-occluso-distal slot-shaped cavities were cut and restored with a conventional (SupremePlus) or low-shrink (RefleXions, Premise, Kalore, and LS) composite (N = 5). We digitized the coronal surfaces before and 10 min after restoration to determine cuspal deflection from the buccal and lingual volume change/area. We also determined the main properties involved (total shrinkage, post-gel shrinkage, degree of conversion, and elastic modulus), as well as microleakage, to verify adequate bonding. It was shown that, due to shrinkage stresses, buccal and lingual surfaces pulled inward after restoration (9-14 microns). Only Kalore and LS resulted in significantly lower tooth deformation (ANOVA/Student-Newman-Keuls post hoc, p = 0.05). The other two low-shrink composites, despite having the lowest and highest total shrinkage values, did not cause significant differences in cuspal deflection. Deflection seemed most related to the combination of post-gel shrinkage and elastic modulus. Therefore, even for significantly lower total shrinkage values, shrinkage stress is not necessarily reduced.

Can fiber posts increase root stresses and reduce fracture?

The clinical success of fiber posts has been attributed to their lower elastic modulus. The tested hypothesis was that fiber posts could lead to lower risk of post debonding and lower risk of root fracture, despite an increase in root stresses. Stress analyses were carried out with a 3D finite element model of a premolar restored with a metallic or a fiber post. Bonded and non-bonded post/cement interface conditions were simulated. We calculated risk-of-fracture indices by determining the highest principal stress values divided by the tensile strength. Shear stresses along the post/cement interface were analyzed for the bonded models. Compared with the premolar restored with a metallic post, the fiber post generated lower stresses along the interface and higher stresses in the root. However, with the fiber post, fracture was less likely to occur in the root, since its core and post fracture indices were higher.