Reverberation time and audibility in phased geometrical acoustics using plane or spherical wave reflection coefficients.

Room acoustics parameters are typically predicted using some form of geometrical acoustics for large rooms. For smaller rooms, phased geometrical acoustics improves results for lower frequencies. The use of a spherical wave reflection coefficient improves the results further, yet the exact impact on room acoustics parameters is not fully known. This work predicts the reverberation time in medium-sized rooms (27 m3 < V < 300 m3) using phased geometrical acoustics. The difference between the use of plane and spherical wave reflection modeling is analyzed for a variety of boundary conditions, including non-uniform distribution of absorption. Since calculated differences are greater than the conventional just-noticeable-difference of 5% for reverberation time, laboratory listening tests are performed to confirm audibility of the modeled differences. Two narrow band noise stimuli (octave bands with central frequency 125 and 250 Hz) with a duration of 1 s were used for comparisons of 18 acoustic scenarios by means of a three-alternative forced choice method. More than half of the listeners could hear the differences in all 36 cases. Statistically significant results (chi-squared test was used) were found in two-thirds of the cases, corresponding to those with longer reverberation times.

Interference effects in phased beam tracing using exact half-space solutions.

Geometrical acoustics provides a correct solution to the wave equation for rectangular rooms with rigid boundaries and is an accurate approximation at high frequencies with nearly hard walls. When interference effects are important, phased geometrical acoustics is employed in order to account for phase shifts due to propagation and reflection. Error increases, however, with more absorption, complex impedance values, grazing incidence, smaller volumes and lower frequencies. Replacing the plane wave reflection coefficient with a spherical one reduces the error but results in slower convergence. Frequency-dependent stopping criteria are then applied to avoid calculating higher order reflections for frequencies that have already converged. Exact half-space solutions are used to derive two additional spherical wave reflection coefficients: (i) the Sommerfeld integral, consisting of a plane wave decomposition of a point source and (ii) a line of image sources located at complex coordinates. Phased beam tracing using exact half-space solutions agrees well with the finite element method for rectangular rooms with absorbing boundaries, at low frequencies and for rooms with different aspect ratios. Results are accurate even for long source-to-receiver distances. Finally, the crossover frequency between the plane and spherical wave reflection coefficients is discussed.

Reconstruction of the in-plane mode shape of a rotating tire with a continuous scanning measurement using the Hilbert-Huang transform.

Generally, the dynamic characteristics (natural frequency, damping, and mode shape) of a structure can be estimated by experimental modal analysis. Among these dynamic characteristics, mode shape requires multiple measurements of the structure at different positions, which increases the experimental cost and time. Recently, the Hilbert-Huang transform (HHT) method has been introduced to extract mode-shape information from a continuous measurement, which requires vibration measurements from one position to another position continuously with a non-contact sensor. In this research study, an effort has been made to estimate the mode shapes of a rolling tire with a single measurement instead of using the conventional experimental setup (i.e., measurement of the vibration of a rolling tire at multiple positions similar to the case of a non-rotating structure), which is used to estimate the dynamic behavior of a rolling tire. For this purpose, HHT, which was used in the continuous measurement of a non-rotating structure in previous research studies, has been used for the case of a rotating system in this study. Ambiguous mode combinations can occur in this rotating system, and therefore, a method to overcome this ambiguity is proposed in this study. In addition, the specific phenomenon for a rotating system is introduced, and the effect of this phenomenon with regard to the obtained results through HHT is investigated.

A minimal model for glycemia control in critically ill patients.

In this paper we propose a modified minimal model to be used for glycemia control in critically ill patients. For various reasons the Bergman minimal model is widely used to describe glucose and insulin dynamics. However, since this model is mostly valid in a rather restrictive setting, it might not be suitable to be used in a model predictive controller. Simulations show that the new model exhibits a similar glycemia behaviour but clinically more realistic insulin kinetics. Therefore it is potentially more suitable for glycemia control. The designed model is also estimated on a set of critically ill patients giving promising results.