Piezoelectric Nanogenerators Based On BaTiO3/PDMS Composites for High-Frequency Applications.

A series of highly flexible and environmentally friendly composites based on polydimethylsiloxane (PDMS) filled with 200 nm size ferroelectric BaTiO3 (BTO) particles at different concentrations (from 7 to 23 vol %) have been fabricated by a simple dispersion method. The dielectric, piezoelectric, and ultrasonic properties have been studied. The ferroelectric state of BTO was confirmed by differential scanning calorimetry and ultrasonic spectroscopy. The addition of BTO into PDMS strongly affects the dielectric properties of the composites. At low temperatures close to 160 K, the PDMS matrix exhibits a dielectric anomaly related to a dynamic glass transition, which shifts to higher temperatures as the BTO content increases due to the strong interaction between polymer chains and nanoparticles. Ultrasonic measurements demonstrate the appearance of a piezoelectric voltage signal on a thin plate of the composite with the highest available filler concentration (23 vol %) under longitudinal stress applied by a 10 MHz ultrasonic wave. As a result, at room temperature, the detected signal is characterized by output voltage and specific stored energy values of 10 mV and 367.3 MeV/m2, respectively, followed by a further increase with cooling to 35 mV at 150 K. The proposed BTO/PDMS composite system is thus a potential candidate for nanogenerators, namely, a simple, flexible, and lead-free device converting high-frequency (10 MHz) mechanical vibrations into electrical voltage.

Multilayered Composites with Carbon Nanotubes for Electromagnetic Shielding Application.

Bulk polylactic acid (PLA)/multiwall carbon nanotube (MWCNT) composites were prepared and investigated in wide frequency ranges (20 Hz-1 MHz and 24-40 GHz). It was determined that the percolation threshold in bulk PLA/MWCNT composites is close to 0.2 vol.% MWCNT. However, the best microwave dielectric properties and absorption were observed in composites with 3.0-5.0 vol.% MWCNT. Therefore, for future investigations, we selected layered (laminate) polymeric structures with gradual changes in MWCNT concentration from 0.2 to 8.0 vol.% MWCNT. Two approaches to laminate structure designs were examined and compared: a five-layer composite and a nine-layer composite that included four pure PLA middle layers. The addition of MWCNT enhanced the elastic modulus by up to 1.4-fold and tensile strength by up to 1.2-fold, with the best performance achieved at 5.0 vol.% loading. High microwave shielding was observed for these layered PLA/MWCNT structures with a gradient change in MWCNT concentration (up to 26 dB in both transmission and absorption coefficients) in the broad frequency range (from 24 to 40 GHz). Obtained structures are highly anisotropic, and the absorption coefficient is 2-5 dB higher in the direction of MWCNT concentration increase; however, the transmission coefficient is the same in both directions. The properties of microwave absorption are mainly unaffected by the additional polymeric layers. The absorption of the layered structure is greater than the absorption of single-layer composites with an optimal MWCNT concentration of the same thickness. The proposed laminate structure design is promising in the field of efficient electromagnetic shielding.

Electrical Resistivity and Microwave Properties of Carbon Fiber Felt Composites.

We present studies on the microwave properties, electrical resistivity, and low-frequency (10 Hz-20 kHz) noise characteristics in the temperature range of 78 K to 380 K of composite materials made from bisphenol A-based epoxy resin and carbon fiber felts. Two types of carbon fibers were used, derived from polyacrylonitrile or regenerated cellulose. We show that these structures are suitable for electromagnetic shielding applications, especially in the direction parallel to the carbon fibers. The low-frequency voltage fluctuations observed in these materials are of the 1/fα, and the noise intensity is proportional to the square of the voltage. The characteristics of the investigated materials show an instability in the temperature range from 307 K to 332 K. This effect is followed by an increase in resistivity and noise intensity, but it does not change the character of the noise, and this instability vanishes after a few repeated heating and cooling cycles.

0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 Phosphate Composites: Dielectric and Ferroelectric Properties.

Composite materials with 83 wt.% of the 0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 distributed in phosphate-bonded ceramics were prepared at three different pressures. A phosphate matrix comprises a mixture of an aluminum phosphate binder and melted periclase, MgO. All samples demonstrate a homogeneous distribution of the ferroelectric perovskite phase and are thermally stable up to 900 K. At higher temperatures, the pyrochlore cubic phase forms. It has been found that the density of the composites non-monotonously depends on the pressure. The dielectric permittivity and losses substantially increase with the density of the samples. The fabricated composites demonstrate diffused ferroelectric-paraelectric transition and prominent piezoelectric properties.

Outstanding Radiation Tolerance of Supported Graphene: Towards 2D Sensors for the Space Millimeter Radioastronomy.

We experimentally and theoretically investigated the effects of ionizing radiation on a stack of graphene sheets separated by polymethyl methacrylate (PMMA) slabs. The exceptional absorption ability of such a heterostructure in the THz range makes it promising for use in a graphene-based THz bolometer to be deployed in space. A hydrogen/carbon ion beam was used to simulate the action of protons and secondary ions on the device. We showed that the graphene sheets remain intact after irradiation with an intense 290 keV ion beam at the density of 1.5 × 1012 cm-2. However, the THz absorption ability of the graphene/PMMA multilayer can be substantially suppressed due to heating damage of the topmost PMMA slabs produced by carbon ions. By contrast, protons do not have this negative effect due to their much longer mean free pass in PMMA. Since the particles' flux at the geostationary orbit is significantly lower than that used in our experiments, we conclude that it cannot cause tangible damage of the graphene/PMMA based THz absorber. Our numerical simulations reveal that, at the geostationary orbit, the damaging of the graphene/PMMA multilayer due to the ions bombardment is sufficiently lower to affect the performance of the graphene/PMMA multilayer, the main working element of the THz bolometer, which remains unchanged for more than ten years.

Terahertz Optics of Materials with Spatially Harmonically Distributed Refractive Index.

The electromagnetic properties of structures with spatially periodic distributed graded refractive index were investigated in the terahertz frequency range. The band structure and electromagnetic response of material with harmonically distributed refractive index were calculated and analyzed. The analytical expressions for frequencies of the first and second bandgap are derived. 3D printed gyroid based architectures were proven to be harmonically graded refractive index structures with designed bandgaps in THz frequency ranges. The transmission coefficient of thermoplastic polyurethane-based samples were experimentally measured in the frequency range 100-500 GHz and compared with theoretical results. Due to losses in the real world produced samples, the predicted response is significantly dumped in the terahertz range and only traces of band gaps are experimentally observed. This funding paves the way toward a new generation of 3D printed THz components for gradient-index optics applications.

Dielectric Relaxation in the Hybrid Epoxy/MWCNT/MnFe2O4 Composites.

The electrical properties of epoxy/MWCNT (multi-walled carbon nanotubes)/MnFe2O4 hybrid composites loaded with MWCNTs (below, 0.09 vol.%, and above, 0.58 vol.%, percolation threshold) and varying concentrations of MnFe2O4 up to 10 vol.% were studied in a wide frequency range (20 Hz-40 GHz) at different temperatures (20 K-500 K). At low frequencies, the dielectric permittivity and the electrical conductivity of composites with fixed amounts of MWCNT are strongly dependent on MnFe2O4 content. For MWCNT concentrations above the percolation threshold (i.e., 0.58 vol.%), the electrical conductivity highly decreases with the increase of the MnFe2O4 fraction. In contrast, for the epoxy/MWCNT just below the onset of electrical conductivity (0.09 vol.% of MWCNTs), there exists an optimal concentration of MnFe2O4 inclusions (i.e., 0.025 vol.%), leading to a dramatic increase of the electrical conductivity by three orders of magnitude. The electrical transport in composites is mainly governed by electron tunneling at lower temperatures (below 200 K), and it is highly impacted by the matrix conductivity at higher temperatures (above 400 K). The electrical properties were discussed in terms of the Maxwell-Wagner relaxation and distributions of relaxation times. A non-invasive platform based on dielectric relaxation spectroscopy was proposed for enhancing the synergetic effect coursed by using multiple nanoinclusions in polymer composites just below the percolation threshold.

Polyethylene Composites with Segregated Carbon Nanotubes Network: Low Frequency Plasmons and High Electromagnetic Interference Shielding Efficiency.

Polyethylene (PE) based composites with segregated carbon nanotubes (CNTs) network was successfully prepared by hot compressing of a mechanical mixture of PE and CNT powders. Through comparison with a composite comprising randomly distributed carbon nanotubes of the same concentration, we prove that namely the segregated CNT network is responsible for the excellent electrical properties, i.e. 10-1 S/m at 0.5-1% and 10 S/m at 6-12% of CNT. The investigation of the complex impedance in the frequency range 1 kHz-2 MHz shows that the sign of real part of the dielectric permittivity changes from positive to negative in electrically percolated composites indicating metal-like behavior of CNT segregated network. The obtained negative permittivity and AC conductivity behavior versus frequency for high CNT content (3%-12%) are described by the Drude model. At the same time, in contrast to reflective metals, high electromagnetic shielding efficiency of fabricated PE composites in the frequency range 40-60 GHz, i.e. close to 100% at 1 mm thick sample, was due to absorption coursed by multiple reflection on every PE-CNT segregated network interface followed by electromagnetic radiation absorbed in each isolated PE granule surrounded by conductive CNT shells.

The Phosphate-Based Composite Materials Filled with Nano-Sized BaTiO3 and Fe3O4: Toward the Unfired Multiferroic Materials.

The composite material filled with nano-sized BaTiO3 and Fe3O4 was designed and studied. The aluminium phosphate ceramics was used as a matrix. The XRD analysis demonstrates only the crystalline structure of the fillers used. The thermogravimetric analysis proves the thermal stability of the composites up to 950 K. The Maxwell-Wagner relaxation was observed in the dielectric spectra of the investigated composites. The dielectric spectroscopy proves the close contact between the nanoparticles with the different ferroic ordering. The phosphate-based composites have been proved to be a prospective candidate for the multiphase multiferroic materials design and development.

Ultra-Light Reduced Graphene Oxide Based Aerogel/Foam Absorber of Microwave Radiation.

We present the polarization-dependent highly absorptive in Ka-band composition of conventional polyurethane foam filled with in situ synthesized aerogel coated by reduced graphene oxide (rGO). The rGO-based aerogel was in situ prepared into the open-cell polyurethane foam (PUF) skeleton through a bidirectional freeze-drying process. The aerogel is composed of the flat lamellas stacks, possessing the anisotropic structure and unique electromagnetic properties. Further improvement of the electromagnetic shielding ability was possible by the rGO coating introduction as a coupling layer between PUF and rGO-based aerogel. This enhances the overall conductivity of the resulting composites: 1.41 + 3.33i S/m vs. 0.9 + 2.45i S/m for PUF loaded with in situ synthesized aerogel without rGO coating.With this mechanically robust plane easy to process coating one could achieve -20 dB by power with the record light structure (0.0462 g/cm²). That could compete in view of the weight per cm² even with graphene-based absorbers comprising either dielectric matching elements or back metal reflectors, or both.

Structure and Electromagnetic Properties of Cellular Glassy Carbon Monoliths with Controlled Cell Size.

Electromagnetic shielding is a topic of high importance for which lightweight materials are highly sought. Porous carbon materials can meet this goal, but their structure needs to be controlled as much as possible. In this work, cellular carbon monoliths of well-defined porosity and cell size were prepared by a template method, using sacrificial paraffin spheres as the porogen and resorcinol-formaldehyde (RF) resin as the carbon precursor. Physicochemical studies were carried out for investigating the conversion of RF resin into carbon, and the final cellular monoliths were investigated in terms of elemental composition, total porosity, surface area, micropore volumes, and micro/macropore size distributions. Electrical and electromagnetic (EM) properties were investigated in the static regime and in the Ka-band, respectively. Due to the phenolic nature of the resin, the resultant carbon was glasslike, and the special preparation protocol that was used led to cellular materials whose cell size increased with density. The materials were shown to be relevant for EM shielding, and the relationships between those properties and the density/cell size of those cellular monoliths were elucidated.