Influence of airborne particle abrasion on dentin bonding effectiveness of a 2-step universal adhesive.

OBJECTIVE: To determine the effect of airborne particle abrasion (APA) on micro-tensile bond strength (µTBS) to dentin using different air-abrasion/polishing powders. METHODS: The bonding effectiveness of G2 Bond Universal (G2B), used in etch-and-rinse (E&R) and self-etch mode (SE), was tested on bur-cut dentin and dentin air abraded/polished using six different powders (aluminum oxide 29 µm (AO29) and 53 µm (AO53), aluminum trihydroxide (AT), sodium bicarbonate (SB), sodium bicarbonate soft (SBsoft) and bioactive glass (BG); Velopex). Adhesive-composite resin specimens were immersed in distilled water at 37 °C for one week and cut into microspecimens. Half of the specimens were subjected to 50,000 thermocycles (aged). Immediate and aged µTBS to dentin were measured. Statistical analysis was performed using linear mixed-effects (LME) modeling (p < 0.05). RESULTS: Comparing the aged bond strengths to air-abraded/polished dentin with bur-cut dentin, pretreatment with SB and SBsoft in combination with G2B used in E&R mode, and BG air polishing in combination with both application modes (E&R, SE), resulted in a significantly higher bond strength. Dentin bond strength was only significantly lower when air abraded with AO29 and using G2B in SE mode. Aging did not significantly influence bond strength for both application modes (E&R, SE), except for AO29 and AT-treated dentin, where bond strengths decrea sed significantly using G2B in SE mode. In general, G2B reached significantly higher bond strengths on air-abraded/polished dentin in E&R mode than in SE mode. CONCLUSION: Air-abrasion/polishing did not impair dentin bond strength using G2B, except when dentin was air abraded with AO29 and using G2B in SE mode. Air polishing positively influenced the bond strength to dentin in specific groups. CLINICAL SIGNIFICANCE: APA is safe concerning bonding to dentin. The E&R application mode is preferred using G2B as adhesive on air-abraded/polished dentin. Air polishing with BG positively influenced dentin bond strength for both application methods.

Correlation between periodontal disease, inflammatory alterations and pre-eclampsia.

BACKGROUND AND OBJECTIVE: Several studies have hypothesized that periodontal disease may increase the risk of pre-eclampsia. The correlation between the two diseases would probably be based on hypertension-related cytokine release in the local periodontal environment. The aim of this study was to evaluate the association between periodontal disease and pre-eclampsia, and the correlation of the two conditions with interleukin-6 (IL-6) and tumor necrosis factor-α(TNFα) mRNA expression. MATERIAL AND METHODS: A case-control analysis of 116 pregnant women, 58 with pre-eclampsia (cases) and 58 normotensive pregnant women (controls) was performed. In addition to collection of socio-demographic data and periodontal evaluation, peripheral blood samples were collected for laboratory analysis of IL-6 and TNFα mRNA expression by real-time PCR. RESULTS: There was an association between periodontitis and pre-eclampsia (adjusted odds ratio 3.73; 95% confidence interval 1.32-10.58). Increased TNFα mRNA expression was observed in pre-eclamptic women; however, there was no correlation between periodontitis and systemic cytokine expression. In the case group, systemic cytokine mRNA levels were similar in pregnant women with and without periodontitis (means±SD): 0.73±0.24 vs. 0.82±0.38 for TNFα and 1.31±1.49 vs. 1.09±0.74 for IL-6, respectively. CONCLUSION: Periodontitis was clinically related to pre-eclampsia; however, the supposed mechanism that correlates the two diseases, i.e. a systemic inflammatory process involving cytokines TNFα and IL-6 in the presence of periodontal disease, could not be confirmed in this study.