Effect of Pt on Stress Rupture Properties of Pt-Modified Nickel Aluminide Coatings at 1100 °C.

Platinum plays a crucial role in the superior high-temperature oxidation resistance of Pt-modified nickel aluminide (PtAl) coatings. However, PtAl coatings usually serve in thermo-mechanical coupling environments. To investigate whether Pt contributes to the high-temperature mechanical properties of PtAl coating, stress rupture tests under 1100 °C/100 MPa were performed on PtAl coatings with varying Pt contents. The different coatings were obtained by changing the thickness of the electroplated Pt layer, followed by a diffusion heat treatment and the aluminizing process in the present work. The results of the stress rupture tests indicated that an increasing Pt content resulted in a significant decrease in the stress rupture life of PtAl-coated superalloys under 1100 °C/100 MPa. Theoretical calculations and microstructural analysis suggested that an increased coating thickness due to the Pt content is not the main reason for this decline. It was found that the cracks generated close to the substrate in high-Pt-coated superalloys accelerated the fracture failure.

Enhanced degradation performance of Fe75B12.5Si12.5 amorphous alloys on azo dye.

The Fe75B12.5Si12.5 and Fe75B12.5C12.5 amorphous alloy ribbons were prepared by the melt spinning method. The decolorization performances of these ribbons were investigated in details. It is found that the Fe75B12.5C12.5 amorphous ribbons and Fe75B12.5Si12.5 annealed ribbons only adsorbed the azo dye molecules, with no chemical degradation process. However, the Fe75B12.5Si12.5 amorphous ribbons can reduce -N = N- to -NH2 because of their high reactivity and the local galvanic effect that occurred during the reaction to accelerate electron transfer. The reaction rate constant kobs is 0.0872 min-1, 0.0474 min-1, and 0.0064 min-1 for Fe75B12.5Si12.5 amorphous ribbons, Fe75B12.5C12.5 amorphous ribbons, and Fe75B12.5Si12.5 annealed ribbons in the same condition, respectively. Fe75B12.5Si12.5 amorphous ribbons can effectively degrade Acid Orange II (AO II) azo dyes and achieve decolorization by breaking azo bonds in the dye in a short time, indicating the prominent capacity of Fe75B12.5Si12.5 ribbons on the degradation of AO II. Furthermore, the influence of chemical factors such as ribbons thickness, reaction temperature, initial pH, and AO II concentration of the solution on the reaction rate constant kobs of Fe75B12.5Si12.5 amorphous ribbons had also been studied. The kobs can reach 0.177 min-1 under optimal conditions. In addition, all the degradation processes in this work were fitted well with the pseudo-first-order kinetic model. The results are guidance for the practical applications, and they have important implications in developing Fe-based amorphous alloys for functional application materials in the field of wastewater treatment.

The Preparation of High Saturation Magnetization and Low Coercivity Feco Soft Magnetic Thin Films via Controlling the Thickness and Deposition Temperature.

FeCo thin films with high saturation magnetization (4 πMs) can be applied in high-frequency electronic devices such as thin film inductors and microwave noise suppressors. However, due to its large magnetocrystalline anisotropy constant and magnetostrictive coefficient of FeCo, the coercivity (Hc) of FeCo films is generally high, which is detrimental to the soft magnetic properties. Meanwhile, the thickness and deposition temperature have significant effects on the coercivity and saturation magnetization of FeCo films. In this paper, FeCo thin films with different thicknesses were prepared by magnetron sputtering at different temperatures. The effects of thickness and deposition temperature on the microstructure and magnetic properties of FeCo thin films were systematically studied. When the film thickness increases from 50 nm to 800 nm, the coercivity would decrease from 309 Oe to 160 Oe. However, the saturation magnetization decreases from 22.1 kG to 15.3 kG. After that, we try to further increase the deposition temperature from room temperature (RT) to 475 °C. It is intriguing to find that the coercivity greatly decreased from 160 Oe to 3 Oe (decreased by 98%), and the saturation magnetization increased from 15.3 kG to 23.5 kG (increased by 53%) for the film with thickness of 800 nm. For the film with thickness of 50 nm, the coercivity also greatly decreased from 309 Oe to 10 Oe (decreased by 96%), but the saturation magnetization did not change significantly. It is contributed to the increase of deposition temperature, which will lead to the increase of grain size and the decrease of the number of grain boundaries. And the coercivity decreases as the number of grain boundaries decreases. Meanwhile, for the thicker films, when increasing the deposition temperature the thermal stress increases, which changes the appearance of (200) texture, and the saturation magnetization increases. Whereas, it has a negligible effect on the orientation of thin films with small thickness (50 nm). This indicates that high-temperature deposition is beneficial to the soft magnetic properties of FeCo thin films, particularly for the films with larger thickness. This FeCo thin film with high saturation magnetization and low coercivity could be an ideal candidate for high-frequency electronic devices.

Experimental study and finite element analysis based on equivalent load method for laser ultrasonic measurement of elastic constants.

The laser ultrasonic generation of Rayleigh surface wave and longitudinal wave in an elastic plate is studied by experiment and finite element method. In order to eliminate the measurement error and the time delay of the experimental system, the linear fitting method of experimental data is applied. The finite element analysis software ABAQUS is used to simulate the propagation of Rayleigh surface wave and longitudinal wave caused by laser excitation on a sheet metal sample surface. The equivalent load method is proposed and applied. The pulsed laser is equivalent to the surface load in time and space domain to meet the Gaussian profile. The relationship between the physical parameters of the laser and the load is established by the correction factor. The numerical solution is in good agreement with the experimental result. The simple and effective numerical and experimental methods for laser ultrasonic measurement of the elastic constants are demonstrated.