Preparation and functionalization of cellulose nanofibers using a naturally occurring acid and their application in stabilizing linseed oil/water Pickering emulsions.

Finding efficient and environmental-friendly methods to produce and chemically modify cellulose nanofibers (CNFs) remains a challenge. In this study, lactic acid (LA) treatment followed by microfluidization was employed for the isolation and functionalization of CNFs. Small amounts of HCl (0.01, 0.1, and 0.2 M) were used alongside LA to intensify cellulose hydrolysis. FTIR spectroscopy and solid-state 13C NMR confirmed the successful functionalization of CNFs with lactyl groups during isolation, while SEM, AFM, and rheological tests revealed that the addition of HCl governed the fibers' sizes and morphology. Notably, the treatment with LA and 0.2 M HCl resulted in a more efficient defibrillation, yielding smaller nanofibers sizes (62 nm) as compared to the treatment with LA or HCl alone (90 and 108 nm, respectively). The aqueous suspension of CNFs treated with LA and 0.2 M HCl showed the highest viscosity and storage modulus. LA-modified CNFs were tested as stabilizers for linseed oil/water (50/50 v/v) emulsions. Owing to the lactyl groups grafted on their surface and higher aspect ratio, CNFs produced with 0.1 and 0.2 M HCl led to emulsions with increased stability (a creaming index increase of only 3 % and 1 %, respectively, in 30 days) and smaller droplets sizes of 23.4 ± 1.2 and 35.5 ± 0.5 µm, respectively. The results showed that LA-modified CNFs are promising stabilizers for Pickering emulsions.

Cellulose Fabrics Functionalized with Sol-Gel Photocatalytic Coatings Based on Iron (III) Phthalocyanine Tetracarboxylic Acids-TiO2-Silica Hybrids.

Photocatalytic coatings are difficult to obtain on textile materials because of the sometimes contradictory properties that must be achieved. In order to obtain a high efficiency of a photocatalytic effect, the metal-oxide semiconductor must be found in the vicinity of the coating-air interface in order to come into direct contact with the contaminant species and allow light radiation access to its surface. Another necessary condition is related to the properties of the covering textile material as well as to the stability of the xerogel films to light and wet treatments. In this sense, we proposed a solution based on hybrid silica films generated by sol-gel processes, coatings that contain as a photocatalyst TiO2 sensitized with tetracarboxylic acid of iron (III) phthalocyanine (FeTCPc). The coatings were made by the pad-dry-cure process, using in the composition a bifunctional anchoring agent (3-glycidoxipropyltrimethoxysilane, GLYMO), a crosslinking agent (sodium tetraborate, BORAX), and a catalyst (N-methylimidazole, MIM) for the polymerization of epoxy groups. The photodegradation experiments performed on methylene blue (MB), utilized as a model contaminant, using LED or xenon arc as light sources, showed that the treatment with BORAX improves the resistance of the coatings to wet treatments but worsens their photocatalytic performances.

New Biodegradable Materials for Re-Thought Packaging from Pre-Consumer Wastes by Controlling the Storage Time as Method to Increase the Mechanical Recycling Efficiency.

The influence of storage conditions on the mechanical recycling of pre-consumer waste (PRE-CW) from the manufacture of multilayer packaging films starting from starch compounds using a renewable-based polymer with PCL and PBAT, which are biodegradable conventional-based polyesters, was studied. It was found that, unlike materials based on conventional-origin polymers that accumulate in the environment for hundreds of years, the studied compounds degraded, even in the solid state, duringstorage in unventilated spaces and during the rainy hot summers with alternatingheat and rain. The degradation of the mechanically recycled compounds obtained from PRE-CW stored in such conditions was highlighted by the comparative analysis with the primary compounds, which proved the following: specific FTIR spectra changes; 2-3-times higher melt fluidity than for primary compounds; melting in successive processes over the entire positive temperatures range, up to 115 °C, such as in cases of compositional de-mixing of incompatible blends, faced to a single melting endotherm with a maximum at around 120 °C for the primar thermal degradation with the movement of the main destruction stages towards higher temperatures; a high quantity residue at 750 °C in air; dispersed mechanical resistance properties y compounds; crystallization at temperatures 10 °C-15 °C higher. The elimination of storage before the mechanical recycling of the pre-consumer waste from this type of polymeric compound fabrication is a way to increase the mechanical recycling efficiency while obtaining new materials with functional properties required by the applications.

Bio-Based Poly(lactic acid)/Poly(butylene sebacate) Blends with Improved Toughness.

A series of poly(butylene sebacate) (PBSe) aliphatic polyesters were successfully synthesized by the melt polycondensation of sebacic acid (Se) and 1,4-butanediol (BDO), two monomers manufactured on an industrial scale from biomass. The number average molecular weight (Mn) in the range from 6116 to 10,779 g/mol and the glass transition temperature (Tg) of the PBSe polyesters were tuned by adjusting the feed ratio between the two monomers. Polylactic acid (PLA)/PBSe blends with PBSe concentrations between 2.5 to 20 wt% were obtained by melt compounding. For the first time, PBSe's effect on the flexibility and toughness of PLA was studied. As shown by the torque and melt flow index (MFI) values, the addition of PBSe endowed PLA with both enhanced melt processability and flexibility. The tensile tests and thermogravimetric analysis showed that PLA/PBSe blends containing 20 wt% PBSe obtained using a BDO molar excess of 50% reached an increase in elongation at break from 2.9 to 108%, with a negligible decrease in Young's modulus from 2186 MPa to 1843 MPa, and a slight decrease in thermal performances. These results demonstrated the plasticizing efficiency of the synthesized bio-derived polyesters in overcoming PLA's brittleness. Moreover, the tunable properties of the resulting PBSe can be of great industrial interest in the context of circular bioeconomy.

Highlighting Bacteria with Calcifying Abilities Suitable to Improve Mortar Properties.

Biomineralization, the use of microorganisms to produce calcium carbonate, became a green solution for application in construction materials to improve their strength and durability. The calcifying abilities of several bacteria were investigated by culturing on a medium with urea and calcium ions. The characterization of the precipitates from bacterial cultures was performed using X-ray diffraction, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The formation of carbonate crystals was demonstrated by optical and scanning electron microscopy. Water absorption and compressive strength measurements were applied to mortars embedded with sporal suspension. The efficiency of the supplementation of mortar mixtures with bacterial cells was evaluated by properties, namely the compressive strength and the water absorption, which are in a relationship of direct dependence, the increase in compressive strength implying the decrease in water absorption. The results showed that Bacillus subtilis was the best-performing bacterium, its introduction into the mortar producing an increase in compressive strength by 11.81% and 9.50%, and a decrease in water absorption by 11.79% and 10.94%, after 28 and 56 days of curing, respectively, as compared to standards. The exploitation of B. subtilis as a calcifying agent can be an interesting prospect in construction materials.

Influence of TEMPO oxidation on the properties of ethylene glycol methyl ether acrylate grafted cellulose sponges.

In this study, cellulose nanofibers (CNF) obtained via high-pressure microfluidization were 2,6,6-tetra-methylpiperidine-1-oxyl (TEMPO) oxidized (TOCNF) in order to facilitate the grafting of ethylene glycol methyl ether acrylate (EGA). FTIR and XPS analyses revealed a more efficient grafting of EGA oligomers on the surface of TOCNF as compared to the original CNF. As a result, a consistent covering of the TOCNF fibers with EGA oligomers, an increased hydrophobicity and a reduction in porosity were noticed for TOCNF-EGA. However, the swelling ratio of TOCNF-EGA was similar to that of original CNF grafted with EGA and higher than that of TOCNF, because the higher amount of grafted EGA onto oxidized cellulose and the looser structure reduced the contacts between the fibrils and increased the absorption of water. All these results corroborated with a good cytocompatibility and compression strength recommend TOCNF-EGA for applications in regenerative medicine.

Iron Oxide/Phosphatic Materials Composites with Potential Applications in Environmental Protection.

Currently, hydroxyapatite is probably the most researched material, due to its multiple applications in medical, environmental, or cultural heritage, when the classical structure is modified and calcium is displaced partially or totally with different metals. By changing the classical structure of the hydroxyapatite, new morphologies can be obtained, thus allowing final applications different from those of the initial hydroxyapatite material. However, their properties should be tuned for the desired application. In this context, the present paper describes the synthesis and characterization (through energy-dispersive X-ray fluorescence, X-ray diffraction, FTIR, thermal analysis, and transmission electron microscopy) of iron oxide/manganese-containing phosphatic phase composite materials, developed in order to obtain the enhancement of final environmental applications (photodegradation of dyes, adsorption of organic compounds). The composite material was tested for photocatalytic properties, after embedding in hydrosoluble film-forming materials. Photocatalytic coatings show different activity during the photodecomposition of Methylene Blue, used as a model of a contaminant. The photocatalytic activities of the materials were discussed in relationship with both the phosphatic materials and the magnetic components. Finally, other environmental applications were studied for the developed materials (adsorption of non-steroidal anti-inflammatory drugs-paracetamol and ibuprofen), revealing an enhancement of the adsorption capacity of the phosphatic material upon addition of the magnetic phase.