RESUMO
Introduction Endodontic implants, or didontic implants, offer a promising solution for stabilizing compromised teeth with a guarded prognosis and prolonging their clinical survival rate. Despite their potential benefits, they retired out of practice due to failures that arose from the lack of a biocompatible seal and engaging in dentin. Novel designs, based on evidence-based research with the help of bioceramics, present an opportunity to overcome these challenges and hence, enhance the clinical efficacy of endodontic implants. Thus the aim of this study is to design novel endodontic implants and evaluate their stress distribution in maxillary incisors using finite element analysis (FEA). Materials and methodology FEA is a biomechanical study to assess the stress distribution and extent of displacement to assess the clinical efficacy of novel endodontic implants in maxillary anterior teeth. Three 3D models (Model 1, Model 2, and Model 3) are designed to be meshed, and material elastic properties of the tooth and periapical tissues are applied. Boundary conditions were established, and a constant axial load value of 600 N was applied at a 45° angle. The FEA analysis was done under the loading conditions to assess the stress patterns for the three 3D models in comparison to the intact tooth on the ANSYS software (ANSYS Inc, Pennsylvania). Results FEA simulations revealed the distribution of stress within the tooth structure under functional occlusal forces, as Von Misses stresses were analyzed to assess the likelihood of material yielding and failure, which was comparable to that of an intact tooth. The maximum stress of deformation was as follows: intact: 1.7589e-5 MAX; Model 1: 3.3804e-6 MAX; Model 2: 2.638e-5 MAX; and Model 3: 2.1986e-5 MAX. The area of stress concentrations did not occur at the interface of the coronal or apical seal, which prevented catastrophic failures. Conclusion By leveraging advanced design principles and materials, these implants offer a promising alternative to traditional approaches, particularly in trauma cases with a poor prognosis for the survival of the teeth leading to loss of tooth. Further clinical studies are warranted to validate the efficacy and long-term success of these novel endodontic implants in diverse patient populations.
RESUMO
Background and objective Resin-based restorative materials are the backbone of modern restorative dentistry. But in spite of being an excellent material, there are many shortcomings with direct resin restorative materials such as polymerization shrinkage and microleakage that complicate the rate of clinical success. Hence, the aim of the present study is to compare the microleakage caused by composite restorations using two different bevels, primary and zigzag bevels, while restoring fractured anterior teeth. Materials and methodology Thirty non-carious maxillary central incisors were split into two divisions wherein Group I received the primary bevel and Group II received the zigzag bevel. After receiving the bevel, the samples are restored with direct filling composite material (Neo Spectra ST, Dentsply Sirona, Charlotte, NC, USA). The restored samples underwent thermocycling (Holmarc, Kochi, India) and were assessed for microleakage under a stereomicroscope (Leica M205, Wetzlar, Germany). For the statistical analysis, IBM SPSS Statistics for Windows, V. 23.0 (IBM Corp., Armonk, NY) was used. Descriptive statistics were expressed in mean and standard deviation. Analytical statistics including the independent Student t-test was used to assess the difference derived from both groups at p<0.05. The normality of the data was assessed using the Shapiro-Wilk test. Results In the primary bevel, 53.3% of the samples showed first-degree microleakage, and 46.7% showed second-degree microleakage, respectively, and in samples restored using the zigzag bevel, 66.7% of the samples had no microleakage, and 33.3% of the samples had first-degree microleakage. The independent t-test revealed that the microleakage of the zigzag bevel showed a significant difference, being superior to the primary bevel at p<0.01. Conclusion Acknowledging the limitations of the study conducted, both bevel designs had a certain degree of microleakage when restored with composite material in anterior fractured teeth. However, the zigzag bevel produced significantly lesser microleakage as compared to the primary bevel restorations.
RESUMO
Introduction Dental caries is a prevalent oral health issue caused by the colonization of Streptococcus mutans in the oral cavity. Citrullus lanatus, commonly known as watermelon, is rich in bioactive compounds that possess antibacterial potential. In this study, we aimed to synthesize stannous chloride (SnCl2) nanoparticles (NPs) mediated by Citrullus lanatus extract and investigate their antibacterial effectiveness against Streptococcus mutans. Materials and method Stannous nanoparticles (SnNPs) synthesized by the green method were achieved by using the watermelon extract. Dilute stannous chloride solution was obtained by adding 0.45 g of stannous (Sn) chloride (Cl) powder to 60 mL of water, which was subjected to an orbital shaker with the watermelon extract. The nanoparticles obtained were subjected to characterization using antimicrobial testing, Fourier transform infrared (FTIR) spectroscopy, energy-dispersive X-ray (EDAX) analysis, and scanning electron microscopy (SEM). Agar well diffusion method was used against specific strains of S. aureus, S. mutans, and Escherichia coli. Results The novel nanoparticles demonstrated promising antibacterial activity against S. mutans providing 10 mm of inhibitory action. Conclusion Due to its abundance of naturally occurring bioactive chemicals and improved efficacy against S. mutans, watermelon extract can be utilized to create stannous nanoparticles as opposed to the use of toxic chemicals. They can also be employed as oral administration systems.
