Steady state hemodynamic and energetic characterization of the Penn State/3M Health Care Total Artificial Heart.

Total Artificial Heart (TAH) development at Penn State University and 3M Health Care has progressed from design improvements and manufacturing documentation to in vitro and in vivo testing to characterize the system's hemodynamic response and energetic performance. The TAH system is completely implantable and intended for use as an alternative to transplantation. It includes a dual pusher plate pump and rollerscrew actuator, welded electronics and battery assembly, transcutaneous energy transmission system, telemetry, and a compliance chamber. In vitro testing was conducted on a Penn State mock circulatory loop with glycerol/water solution at body temperature. Tests were performed to characterize the preload and afterload response, left atrial pressure control, and power consumption. A sensitive preload response was demonstrated with left atrial pressure safely maintained at less than 15 mm Hg for flow rates up to 7.5 L/min. Variations in aortic pressure and pulmonary vascular resistance were found to have minimal effects on the preload sensitivity and left atrial pressure control. In vivo testing of the completely implanted system in its final configuration was carried out in two acute studies using implanted temperature sensors mounted on the electronics, motor, and energy transmission coil in contact with adjacent tissue. The mean temperature at the device-tissue interface was less than 4 degrees C above core temperature.

Dynamic in vitro and in vivo performance of a permanent total artificial heart.

In vivo characterization studies were performed to compare the dynamic in vivo performance of the Penn State/3M Health Care electric total artificial heart to existing in vitro data. Fully implanted systems were utilized including the artificial heart, controller, backup batteries, compliance chamber, and transcutaneous energy transmission. Catheters were implanted to measure central venous pressure (CVP), left atrial pressure (LAP), right atrial pressure (RAP), pulmonary artery pressure (PAP), and aortic pressure (AoP). Cardiac output (CO) was determined from the implanted controller, and systemic vascular resistance (SVR) was calculated. Steady state data were collected for each animal along with data regarding the transient responses to changes in preload and afterload. Preload was manipulated through volume changes. Afterload changes were accomplished through vasoactive agents. Increased preload caused little change in cardiac output because the pump output was nearly maximum at baseline. LAP, AoP, and SVR increased with increasing RAP. Decreased preload caused a reduction in CO, LAP, and SVR. Afterload increase resulted in a slight decrease in flow and an increase in system power and SVR. Afterload reduction was accompanied by a decrease in preload and a concomitant reduction in flow. Overall, the system response was similar to the response observed in vitro.

An annular compliance chamber for the Pennsylvania State University electric total artificial heart.

To eliminate the need for a separate parapleural compliance chamber, we are currently investigating the feasibility of an annular compliance chamber. This chamber wraps around the energy converter and fits between the blood pumps of the Pennsylvania State University electric total artificial heart. For the 100 cc total artificial heart, the compliance chamber volume is 76 ml and the tissue contacting surface area is approximately 85 cm2. The chamber is made of Dacron velour covered segmented polyether polyurethane urea. The annular compliance chamber was evaluated in vitro by comparing pump balance control performance against that obtained with an open vent. In the CVP range of 5-12 mmHg, LAP was maintained within 1 mmHg of the values obtained with a vent. Studies continue to determine the range of volumes over which the chamber is effective, differences in rates of diffusion, and performance during changes in barometric pressure.

A completely implanted left ventricular assist device. Chronic in vivo testing.

A completely implantable left ventricular assist device (LVAD) designed for permanent circulatory support has recently been tested in animals without the use of percutaneous leads, using transcutaneous energy transmission and wireless telemetry. The LVAD consists of a brushless DC motor and rollerscrew energy converter, a pusher plate actuated blood pump with a seamless segmented polyurethane blood sac, Bjork-Shiley Delrin disk monostrut valves, an implanted compliance chamber, an implanted electronic controller and battery, and a transcutaneous energy transmission system. The blood pump/energy converter assembly weighs 565 g and displaces 295 cc. The dynamic stroke volume is 60 ml, and the maximum output is 9 L/min. Pump output is automatically controlled to maintain full stroke volume as preload varies. Hall effect sensors for detecting rotary position of the motor are the only sensors used. Six bovine implants were performed, with durations of 84, 208, 244, 130, 70 (ongoing), and 15 (ongoing) days. Four animals used two-way telemetry, whereas the remaining two used one-way (outgoing) telemetry. These first chronic in vivo tests with the Penn State completely implanted LVAD system have demonstrated that it is a feasible solution to long-term ventricular support.

An electrically powered total artificial heart. Over 1 year survival in the calf.

An electric motor driven orthotopic artificial heart was implanted in a 110 kg female Holstein calf as part of a series of 12 such implants intended to demonstrate the in vivo durability and compatibility of the device. The device uses pusher plates set into motion by a reversing brushless DC motor and roller screw to alternately eject two cylindrical sac type blood pumps. The pumps use Bjork-Shiley Delrindisc convexo-concave or monostrut valves. The left pump provides an 88-90 ml dynamic stroke volume. Woven Dacron grafts and polyurethane coated Dacron/Lycra cuffs are used to attach the device to the major arteries and atria, respectively. A polyurethane conduit and anchoring skin button bring motor wires percutaneously to an extracorporeal controller. The controller provides balanced cardiac output sensitive to atrial or aortic pressures, without operator intervention. The system is hermetically sealed and uses a simple compliance sac to maintain thoracic pressure between the pumps. The calf recovered uneventfully from surgery and thrived thereafter. She was killed on the 388th post-operative day because of worsening cardiac insufficiency. The previous three operative survivors in this series lived 131, 134, and 204 days. These results indicate the device's good potential for durability and body compatibility.