On the way to SI traceable primary transfer standards for amount of substance measurements in inorganic chemical analysis.

During its 25 years of existence, the Inorganic Analysis Working Group of the Consultative Committee for Amount of Substance: Metrology in Chemistry and Biology (CCQM IAWG) has achieved much in establishing comparability of measurement results. Impressive work has been done on comparison exercises related to real-world problems in fields such as ecology, food, or health. In more recent attempts, measurements and comparisons were focused on calibration solutions which are the basis of most inorganic chemical measurements. This contribution deals with the question of how to achieve full and transparent SI traceability for the values carried by such solutions. Within this framework, the use of classical primary methods (CPMs) is compared to the use of a primary difference method (PDM). PDM is a method with a dual character, namely a metrological method with a primary character, based on the bundling of many measurement methods for individual impurities, which lead to materials with certified content of the main component. As in classical methods, where small corrections for interferences are accepted, in PDM, many small corrections are bundled. In contrast to classical methods, the PDM is universally applicable to all elements in principle. Both approaches can be used to certify the purity (expressed as mass fraction of the main element) of a high-purity material. This is where the metrological need of National Metrology Institutes (NMIs) for analytical methods meet the challenges of analytical methods. In terms of methods, glow discharge mass spectrometry (GMDS) with sufficient uncertainties for sufficiently small impurity contents is particularly noteworthy for the certification of primary transfer standards (PTS), and isotope dilution mass spectrometry (IDMS), which particularly benefits from PTS (back-spikes) with small uncertainties, is particularly noteworthy for the application. The corresponding relative uncertainty which can be achieved using the PDM is very low (< 10-4). Acting as PTS, they represent the link between the material aspect of the primary calibration solutions and the immaterial world of the International System of Units (SI). The underlying concepts are discussed, the current status of implementation is summarised, and a roadmap of the necessary future activities in inorganic analytical chemistry is sketched. It has to be noted that smaller measurement uncertainties of the purity of high-purity materials not only have a positive effect on chemical measurements, but also trigger new developments and findings in other disciplines such as thermometry or materials science. Primary Transfer Standards (PTSs) are the link between the immaterial world of the International System of Units (SI) and the material aspects of the primary calibration solutions.

Determination of lithium in human serum by isotope dilution atomic absorption spectrometry.

The therapeutic dose of lithium (Li) compounds, which are widely used for the treatment of psychiatric and hematologic disorders, is close to its toxic level; therefore, drug monitoring protocols are mandatory. Herein, we propose a fast, simple, and low-cost analytical procedure for the traceable determination of Li concentration in human serum, based on the monitoring of the Li isotope dilution through the partially resolved isotope shift in its electronic transition around 670.80 nm using a commercially available high-resolution continuum source graphite furnace atomic absorption spectrometer. With this technique, serum samples only require acidic digestion before analysis. The procedure requires three measurements-an enriched 6Li spike, a mixture of a certified standard solution and spike, and a mixture of the sample and spike with a nominal 7Li/6Li ratio of 0.82. Lanthanum has been used as an internal spectral standard for wavelength correction. The spectra are described as the linear superposition of the contributions of the respective isotopes, each consisting of a spin-orbit doublet, which can be expressed as Gaussian components with constant spectral position and width and different relative intensity, reflecting the isotope ratio in the sample. Both the spectral constants and the correlation between isotope ratio and relative band intensity have been experimentally obtained using commercially available materials enriched with Li isotopes. The Li characteristic mass (mc) obtained corresponds to 0.6 pg. The procedure has been validated using five human serum certified reference materials. The results are metrologically comparable and compatible to the certified values. The measurement uncertainties are comparable to those obtained by the more complex and expensive technique, isotope dilution mass spectrometry.

High-Resolution Atomic Absorption Spectrometry Combined With Machine Learning Data Processing for Isotope Amount Ratio Analysis of Lithium.

An alternative method for lithium isotope amount ratio analysis based on a combination of high-resolution atomic absorption spectrometry and spectral data analysis by machine learning (ML) is proposed herein. It is based on the well-known isotope shift of approximately 15 pm for the electronic transition 22P←22S at around the wavelength of 670.8 nm, which can be measured by the state-of-the-art high-resolution continuum source graphite furnace atomic absorption spectrometry. For isotope amount ratio analysis, a scalable tree boosting ML algorithm (XGBoost) was employed and calibrated using a set of samples with 6Li isotope amount fractions, ranging from 0.06 to 0.99 mol mol-1, previously determined by a multicollector inductively coupled plasma mass spectrometer (MC-ICP-MS). The calibration ML model was validated with two certified reference materials (LSVEC and IRMM-016). The procedure was applied toward the isotope amount ratio determination of a set of stock chemicals (Li2CO3, LiNO3, LiCl, and LiOH) and a BAM candidate reference material NMC111 (LiNi1/3Mn1/3Co1/3O2), a Li-battery cathode material. The results of these determinations were compared with those obtained by MC-ICP-MS and found to be metrologically comparable and compatible. The residual bias was -1.8‰, and the precision obtained ranged from 1.9 to 6.2‰. This precision was sufficient to resolve naturally occurring variations, as demonstrated for samples ranging from approximately -3 to +15‰. To assess its suitability to technical applications, the NMC111 cathode candidate reference material was analyzed using high-resolution continuum source atomic absorption spectrometry with and without matrix purification. The results obtained were metrologically compatible with each other.

Comparison and optimization of methods for the simultaneous extraction of DNA, RNA, proteins, and metabolites.

The challenge of performing a time-resolved comprehensive analysis of molecular systems has led to the quest to optimize extraction methods. When the size of a biological sample is limited, there is demand for the simultaneous extraction of molecules representing the four areas of "omics": genomics, transcriptomics, proteomics, and metabolomics. Here we optimized a protocol for the simultaneous extraction of DNA, RNA, proteins, and metabolites and compared it with two existing protocols. Our optimization comprised the addition of a methanol/chloroform metabolite purification before the separation of DNA/RNA and proteins. Extracted DNA, RNA, proteins, and metabolites were quantitatively and/or qualitatively analyzed. Of the three methods, only the newly developed protocol yielded all biomolecule classes of adequate quantity and quality.

Analysis of gadolinium-based contrast agents in tap water with a new hydrophilic interaction chromatography (ZIC-cHILIC) hyphenated with inductively coupled plasma mass spectrometry.

Hydrophilic interaction chromatography (HILIC) coupled with inductively coupled plasma mass spectrometry (ICP-MS) were optimised for the direct determination of gadolinium-based contrast agents in tap water. In comparison to our previous work, a new developed zwitterionic HILIC column (ZIC-cHILIC) was used for speciation of Gd-containing contrast agents. The limit of quantification (LOQ) for the five contrast agents Gd-BOPTA, Gd-DPTA-BMA, Gd-BT-DO3A, Gd-DOTA and Gd-DTPA are in the range of 5-12 ng Gd per litre. Additionally, a new internal standard, Pr-DOTA, was investigated to correct intensity drifts, minor and major changes in the sample volumes and possible matrix effects. With the speciation method described, tap water samples from the area of Berlin were analysed and for the first time, three Gd species, Gd-BT-DO3A, Gd-DOTA and Gd-BOPTA, were found in tap water samples at concentrations of about 10-20 ng Gd per litre. These are the same Gd species which have been previously detected predominantly in surface waters of the Berlin area.

Gravimetric preparation and characterization of primary reference solutions of molybdenum and rhodium.

Gravimetrically prepared mono-elemental reference solutions having a well-known mass fraction of approximately 1 g/kg (or a mass concentration of 1 g/L) define the very basis of virtually all measurements in inorganic analysis. Serving as the starting materials of all standard/calibration solutions, they link virtually all measurements of inorganic analytes (regardless of the method applied) to the purity of the solid materials (high-purity metals or salts) they were prepared from. In case these solid materials are characterized comprehensively with respect to their purity, this link also establishes direct metrological traceability to The International System of Units (SI). This, in turn, ensures the comparability of all results on the highest level achievable. Several national metrology institutes (NMIs) and designated institutes (DIs) have been working for nearly two decades in close cooperation with commercial producers on making an increasing number of traceable reference solutions available. Besides the comprehensive characterization of the solid starting materials, dissolving them both loss-free and completely under strict gravimetric control is a challenging problem in the case of several elements like molybdenum and rhodium. Within the framework of the European Metrology Research Programme (EMRP), in the Joint Research Project (JRP) called SIB09 Primary standards for challenging elements, reference solutions of molybdenum and rhodium were prepared directly from the respective metals with a relative expanded uncertainty associated with the mass fraction of U rel(w) < 0.05 %. To achieve this, a microwave-assisted digestion procedure for Rh and a hotplate digestion procedure for Mo were developed along with highly accurate and precise inductively coupled plasma optical emission spectrometry (ICP OES) and multicollector inductively coupled plasma mass spectrometry (MC-ICP-MS) methods required to assist with the preparation and as dissemination tools.

Determination of major nonmetallic impurities in magnesium by glow discharge mass spectrometry with a fast flow source using sintered and pressed powder samples.

Fast flow glow discharge mass spectrometry with a Grimm-type ion source providing a high sputter rate was used for the determination of major nonmetallic impurities in magnesium. The analytical signal was found to be strongly influenced by the electrical discharge parameters. For calibration by standard addition, synthetic standard samples were produced in two different ways-namely, by pressing and by sintering doped metal powders. The observed sensitivity of the calibration curves was shown to depend on the particle size of the powder. For the magnesium powders, the mass fractions of oxygen, nitrogen, boron, and silicon were determined to be about 0.01 kg·kg(-1) (relative standard deviation approximately 10-20 %), 2,700 mg·kg(-1), 150 mg·kg(-1), and 300 mg·kg(-1), respectively.

Speciation of gadolinium in surface water samples and plants by hydrophilic interaction chromatography hyphenated with inductively coupled plasma mass spectrometry.

Hydrophilic interaction chromatography (HILIC) coupled with inductively coupled plasma mass spectrometry (ICP-MS) was optimized for speciation analysis of gadolinium-based contrast agents in environmental samples, in particular surface river waters and plants. Surface water samples from the Teltow channel, near Berlin, were investigated over a distance of 5 km downstream from the influx of a wastewater treatment plant. The total concentration of gadolinium increased significantly from 50 to 990 ng L(-1) due to the influx of the contrast agents. After complete mixing with the river water, the concentration remained constant over a distance of at least 4 km. Two main substances [Dotarem(®) (Gd-DOTA) and Gadovist(®) (Gd-BT-DO3A)] have been identified in the river water using standards. A gadolinium-based contrast agent, possibly Gd-DOTA (Dotarem(®)), was also detected in water plant samples taken from the Teltow channel. Therefore, uptake of contrast agents [Gadovist(®) (Gd-BTDO3A), Magnevist(®) (Gd-DTPA), Omniscan(®) (Gd-DTPA-BMA), Dotarem(®) (Gd-DOTA), and Multihance(®) (Gd-BOPTA)] by plants was investigated in a model experiment using Lepidium sativum (cress plants). HILIC-ICP-MS was used for identification of different contrast agents, and a first approach for quantification using aqueous standard solutions was tested. For speciation analysis, all investigated contrast agents could be extracted from the plant tissues with a recovery of about 54 % for Multihance(®) (Gd-BOPTA) up to 106 % for Gadovist(®) (Gd-BT-DO3A). These experiments demonstrate that all contrast agents investigated are transported from the roots to the leaves where the highest content was measured.

Mutations in the cardiac transcription factor GATA4 in patients with lone atrial fibrillation.

Familial recurrence of atrial fibrillation (AF) is reported in up to 15% of patients with lone AF. Recently, it was proposed that congenital defects in the morphogenesis of the pulmonary vein myocardium are involved in genetic pathogenesis of lone AF. GATA4 is a cardiac transcription factor essentially involved in myocardial development. Mutations in GATA4 are associated with congenital cardiac malformations. To investigate whether GATA4 mutations represent a genetic origin for AF the coding region of GATA4 was sequenced in 96 patients with lone AF. We found a GATA4 mutation (M247T) in a patient with familial lone AF and atrial septal aneurysm without interatrial shunts. The mutation affects a deeply conserved domain adjacent to the first zinc finger domain of GATA4 and was not reported before. A second GATA4 mutation (A411V) was found in a female patient with sporadic lone AF. This variant was previously reported in patients with cardiac septal defects. However, no anomalies of the atrial or ventricular septa were noted in the AF patient harboring A411V. We report for the first time that mutations in the cardiac transcription factor GATA4 may represent a genetic origin of lone AF. The study proposes that lone AF may share a common genetic origin with congenital cardiac malformations.

Plasma HER2 levels are not associated with cardiac function or hypertrophy in control subjects and heart failure patients.

A proper interaction between the endocardial-derived ligand Neuregulin-1 and the myocardial "Human Epidermal growth factor Receptor 2" (HER2) is essential for maintaining heart function. The shed extracellular domain (ECD) of HER2 circulates in blood and serves as a surrogate marker for breast cancer. Altered cardiac loading conditions are accompanied by dysregulation of the myocardial HER2 gene expression. We studied 193 controls with preserved ejection fraction (EF>55%) and 572 patients with different degrees of systolic heart failure: 98 had EF 45-55%, 138 patients EF 35-44%, and 336 patients, EF <35%, respectively. The corresponding mean HER2 levels were 6.44 ± 0.46 ng/mL, 6.07 ± 0.76 ng/mL and 6.57 ± 0.87 ng/mL, and 6.17 ± 0.71 ng/mL, respectively. Furthermore, there was no significant association between plasma HER2 levels and left ventricular filling pressures or the left ventricular wall thickness. The HER2 plasma levels do not reflect the cardiac function and are therefore not useful as a biomarker for heart failure.

A gain-of-function TBX20 mutation causes congenital atrial septal defects, patent foramen ovale and cardiac valve defects.

BACKGROUND: Ostium secundum atrial septal defects (ASDII) account for approximately 10% of all congenital heart defects (CHD), and mutations in cardiac transcription factors, including TBX20, were identified as an underlying cause for ASDII. However, very little is known about disease penetrance in families and functional consequences of inherited TBX20 mutations. METHODS: The coding region of TBX20 was directly sequenced in 170 ASDII patients. Functional consequences of one novel mutation were investigated by surface plasmon resonance, CD spectropolarymetry, fluorescence spectrophotometry, luciferase assay and chromatin immunoprecipitation. RESULTS: We found a novel mutation in a highly conserved residue in the T-box DNA binding domain (I121M) segregating with CHD in a three generation kindred. Four mutation carriers revealed cardiac phenotypes in terms of cribriform ASDII, large patent foramen ovale or cardiac valve defects. Interestingly, tertiary hydrophobic interactions within the mutant TBX20 T-box were significantly altered leading to a more dynamic structure of the protein. Moreover, Tbx20-I121M resulted in a significantly enhanced transcriptional activity, which was further increased in the presence of co-transcription factors GATA4/5 and NKX2-5. Occupancy of DNA binding sites on target genes was also increased. CONCLUSIONS: We suggest that TBX20-I121M adopts a more fluid tertiary structure leading to enhanced interactions with cofactors and more stable transcriptional complexes on target DNA sequences. Our data, combined with that of others, suggest that human ASDII may be related to loss-of-function as well as gain-of-function TBX20 mutations.

Investigation on the heavy metal content of zinc-carbon and alkaline manganese dry cells.

The objective of this work was to test the compliance of commercially available batteries with the German Battery Ordinance, a project of the German government that was initiated by the Federal Environment Agency. Different types of commercially available dry cells were analysed for their cadmium, lead and mercury contents. The dry cells underwent mechanical pre-treatment, separation of the different components and microwave-assisted digestion before determination of the heavy metals. Mercury is sometimes added to prevent the generation of gaseous hydrogen from the electrochemical process. Lead could be present since it is sometimes used as an alloying element of zinc. Cadmium has no technical importance and is an undesirable impurity. None of the batteries contained higher heavy metal mass fractions than the permissible limits.

Recombinant expression of tatABC and tatAC results in the formation of interacting cytoplasmic TatA tubes in Escherichia coli.

The twin-arginine translocation (Tat) system of bacteria and plant plastids serves to translocate folded proteins across energized biological membranes. In Escherichia coli, the three components TatA, TatB, and TatC mediate this membrane passage. Here we demonstrate that TatA can assemble to form clusters of tube-like structures in vivo. While the presence of TatC is essential for their formation, TatB is not required. The TatA tubes have uniform outer and inner diameters of about 11.5 nm and 6.7 nm, respectively. They align to form a crystalline-like structure in which each tube is surrounded by six TatA tubes. The tube structures become easily detectable even at only a 15-fold overexpression of the tatABC genes. The TatA tubes could also be visualized by fluorescence when untagged TatA was mixed with low amounts of TatA-GFP. The structures were often found in contact with the cell poles. Because TatC is most likely polar in E. coli, as demonstrated by a RR-dependent targeting of translocation-incompatible Tat substrates to the cell poles, and because TatC is required for the formation of aligned TatA tubes, it is proposed that the TatA tubes are initiated at polarly localized TatC.

Investigation on the heavy-metal content of zinc-air button cells.

Within the framework of a German government project (initiated by the Federal Environment Agency) to check the compliance of commercially available batteries with the German Battery Ordinance concerning their heavy metal contents, 18 different types of commercially available zinc-air button cells were analysed for their cadmium, lead and mercury contents. After microwave assisted dissolution with aqua regia, Cd and Pb were determined using inductively coupled plasma mass spectrometry (ICP-MS), and Hg was determined using inductively coupled plasma optical emission spectrometry (ICP OES) and atomic absorption spectrometry. Cd contents were found to be much lower than the permitted limits; Pb contents were also found to be below the limits. Hg contents were found to be near the limits, and in one case the limit was exceeded.

Functional Tat transport of unstructured, small, hydrophilic proteins.

The twin-arginine translocation (Tat) system is a protein translocation system that is adapted to the translocation of folded proteins across biological membranes. An understanding of the folding requirements for Tat substrates is of fundamental importance for the elucidation of the transport mechanism. We now demonstrate for the first time Tat transport for fully unstructured proteins, using signal sequence fusions to naturally unfolded FG repeats from the yeast Nsp1p nuclear pore protein. The transport of unfolded proteins becomes less efficient with increasing size, consistent with only a single interaction between the system and the substrate. Strikingly, the introduction of six residues from the hydrophobic core of a globular protein completely blocked translocation. Physiological data suggest that hydrophobic surface patches abort transport at a late stage, most likely by membrane interactions during transport. This study thus explains the observed restriction of the Tat system to folded globular proteins on a molecular level.

Targeting of unfolded PhoA to the TAT translocon of Escherichia coli.

In Escherichia coli, the Tat system does not translocate Tat signal sequence fused PhoA (RR-PhoA), as it requires disulfide formation for folding. Here we show that such a RR-PhoA construct can be efficiently targeted to the Tat translocon, but the transport is not completed. RR-PhoA is detectable in a 580-kDa TatBC-containing complex, which is the first substrate-bound TatBC complex detected in a bacterial system so far. A second TatBC complex near 440 kDa comprises most of the TatB and TatC but is devoid of RR-PhoA. The targeting of PhoA to the Tat translocon depends on the twin-arginine motif and results in severe growth defects. This physiological effect is likely to be due to proton leakage at the cytoplasmic membrane. The results point to mechanistic incompatibilities of the Tat system with unfolded proteins such as RR-PhoA. There does not exist an intrinsic quality control at the TatBC complex itself, although correct folding is inevitable for Tat-dependent translocation.