Bimolecular Reaction Mechanism in the Amido Complex-Based Atomic Layer Deposition of HfO2.

The surface chemistry of the initial growth during the first or first few precursor cycles in atomic layer deposition is decisive for how the growth proceeds later on and thus for the quality of the thin films grown. Yet, although general schemes of the surface chemistry of atomic layer deposition have been developed for many processes and precursors, in many cases, knowledge of this surface chemistry remains far from complete. For the particular case of HfO2 atomic layer deposition on a SiO2 surface from an alkylamido-hafnium precursor and water, we address this lack by carrying out an operando atomic layer deposition experiment during the first cycle of atomic layer deposition. Ambient-pressure X-ray photoelectron spectroscopy and density functional theory together show that the decomposition of the metal precursor on the stoichiometric SiO2 surface in the first half-cycle of atomic layer deposition proceeds via a bimolecular reaction mechanism. The reaction leads to the formation of Hf-bonded methyl methylene imine and free dimethylamine. In addition, ligand exchange takes place involving the surface hydroxyls adsorbed at defect sites of the SiO2 surface.

Surface photovoltage dynamics at passivated silicon surfaces: influence of substrate doping and surface termination.

We have monitored the temporal evolution of the band bending at controlled silicon surfaces after a fs laser pump excitation. Time-resolved surface photo-voltage (SPV) experiments were performed using time resolved photoemission spectroscopy with time resolution of about 30 ns. To disentangle the influence of doping and surface termination on SPV dynamics, we compare the results obtained on two surface terminations: the water saturated (H,OH)-Si(001) surface and the thermally oxidized Si(001) one. The SPV dynamics were explored as a function of laser fluence and as a function of time for the two surface terminations at given doping levels. The return to equilibrium involves a characteristic time in the 0.1 µs to 10 µs range, depending on the surface termination and bulk doping. Exploring several laser fluences, different SPV regimes were found for the two surface terminations at given doping levels. For low laser fluence the SPV dynamic follows the commonly accepted thermionic model. At higher fluence, the SPV signal reaches a saturation value, and if the fluence is further increased, the decay time of the SPV increases and can no longer be explained by a thermionic model alone.

The Fermi level as an energy reference in liquid jet X-ray photoelectron spectroscopy studies of aqueous solutions.

To advance the understanding of key electrochemical and photocatalytic processes that depend on the electronic structure of aqueous solutions, X-ray photoemission spectroscopy has become an invaluable tool, especially when practiced with liquid microjet setups. Determining vertical ionization energies referenced to the vacuum level, and binding energies referenced to the Fermi level, including the much-coveted reorganization energy of the oxidized species of a redox couple, requires that energy levels be properly defined. The present paper addresses specifically how the vacuum level "just outside the surface" can be known through the energy position of the rising edge of the secondary electrons, and how the Fermi level reference is uniquely determined via the introduction of a redox couple. Taking the case of the ferricyanide/ferrocyanide and ferric/ferrous couples, this study also tackles issues related to the electrokinetic effects inherent to the production of a liquid jet in a vacuum, which has become the standard water sample environment for photoemission experiments.

Chemical Evolution of Pt-Zn Nanoalloys Dressed in Oleylamine.

We report on the shape, composition (from Pt95Zn5 to Pt77Zn23), and surface chemistry of Pt-Zn nanoparticles obtained by reduction of precursors M2+(acac)2- (M2+: Pt2+ and Zn2+) in oleylamine, which serves as both solvent and ligand. We show first that the addition of phenyl ether or benzyl ether determines the composition and shape of the nanoparticles, which point to an adsorbate-controlled synthesis. The organic (ligand)/inorganic (nanoparticles) interface is characterized on the structural and chemical level. We observe that the particles, after washing with ethanol, are coated with oleylamine and the oxidation products of the latter, namely, an aldimine and a nitrile. After exposure to air, the particles oxidize, covering themselves with a few monolayer thick ZnO film, which is certainly discontinuous when the particles are low in zinc. Pt-Zn particles are unstable and prone to losing Zn. We have strong indications that the driving force is the preferential oxidation of the less noble metal. Finally, we show that adsorption of CO on the surface of nanoparticles modifies the oxidation state of amine ligands and attribute it to the displacement of hydrogen adsorbed on Pt. All the structural and chemical information provided by the combination of electron microscopy and X-ray photoelectron spectroscopy allows us to give a fairly accurate picture of the surface of nanoparticles and to better understand why Pt-Zn alloys are efficient in certain electrocatalytic reactions such as the oxidation of methanol.

Hydrogen Bonding of Ammonia with (H,OH)-Si(001) Revealed by Experimental and Ab Initio Photoelectron Spectroscopy.

Combining experimental and ab initio core-level photoelectron spectroscopy (periodic DFT and quantum chemistry calculations), we elucidated how ammonia molecules bond to the hydroxyls of the (H,OH)-Si(001) model surface at a temperature of 130 K. Indeed, theory evaluated the magnitude and direction of the N 1s (and O 1s) chemical shifts according to the nature (acceptor or donor) of the hydrogen bond and, when confronted to experiment, showed unambiguously that the probe molecule makes one acceptor and one donor bond with a pair of hydroxyls. The consistency of our approach was proved by the fact that the identified adsorption geometries are precisely those that have the largest binding strength to the surface, as calculated by periodic DFT. Real-time core-level photoemission enabled measurement of the adsorption kinetics of H-bonded ammonia and its maximum coverage (0.37 ML) under 1.5 × 10-9 mbar. Experimental desorption free energies were compared to the magnitude of the adsorption energies provided by periodic DFT calculations. Minority species were also detected on the surface. As in the case of H-bonded ammonia, DFT core-level calculations were instrumental to attribute these minority species to datively bonded ammonia molecules, associated with isolated dangling bonds remaining on the surface, and to dissociated ammonia molecules, resulting largely from beam damage.

Soft X-ray Heterogeneous Radiolysis of Pyridine in the Presence of Hydrated Strontium-Hydroxyhectorite and its Monitoring by Near-Ambient Pressure Photoelectron Spectroscopy.

The heterogeneous radiolysis of organic molecules in clays is a matter of considerable interest in astrochemistry and environmental sciences. However, little is known about the effects of highly ionizing soft X-rays. By combining monochromatized synchrotron source irradiation with in situ Near Ambient Pressure X-ray Photoelectron Spectroscopy (in the mbar range), and using the synoptic view encompassing both the gas and condensed phases, we found the water and pyridine pressure conditions under which pyridine is decomposed in the presence of synthetic Sr2+-hydroxyhectorite. The formation of a pyridine/water/Sr2+ complex, detected from the Sr 3d and N 1s core-level binding energies, likely presents a favorable situation for the radiolytic breaking of the O-H bond of water molecules adsorbed in the clay and the subsequent decomposition of the molecule. However, decomposition stops when the pyridine pressure exceeds a critical value. This observation can be related to a change in the nature of the active radical species with the pyridine loading. This highlights the fact that the destruction of the molecule is not entirely determined by the properties of the host material, but also by the inserted organic species. The physical and chemical causes of the present observations are discussed.

CO oxidation activity of Pt, Zn and ZnPt nanocatalysts: a comparative study by in situ near-ambient pressure X-ray photoelectron spectroscopy.

The investigation of nanocatalysts under ambient pressure by X-ray photoelectron spectroscopy gives access to a wealth of information on their chemical state under reaction conditions. Considering the paradigmatic CO oxidation reaction, a strong synergistic effect on CO catalytic oxidation was recently observed on a partly dewetted ZnO(0001)/Pt(111) single crystal surface. In order to bridge the material gap, we have examined whether this inverse metal/oxide catalytic effect could be transposed on supported ZnPt nanocatalysts deposited on rutile TiO2(110). Synchrotron radiation near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) operated at 1 mbar of O2 : CO mixture (4 : 1) was used at a temperature range between room temperature and 450 K. To tackle the complexity of the problem, we have also studied the catalytic activity of nanoparticles (NPs) of the same size, consisting of pure Pt and Zn nanoparticles (NPs), for which, moreover, NAP-XPS studies are a novelty. The comparative approach shows that the CO oxidation process is markedly different for the pure Pt and pure Zn NPs. For pure Pt NPs, CO poisoned the metallic surfaces at low temperature at the onset of CO2 evolution. In contrast, the pure Zn NPs first oxidize into ZnO, and trap carbonates at low temperature. Then they start to release CO2 in the gas phase, at a critical temperature, while continuously producing it. The pure Zn NPs are also immune to support encapsulation. The bimetallic nanoparticle borrows some of its characteristics from its two parent metals. In fact, the ZnPt NP, although produced by the sequential deposition of platinum and zinc, is platinum-terminated below the temperature onset of CO oxidation and poisoned by CO. Above the CO oxidation onset, the nanoparticle becomes Zn-rich with a ZnO shell. Pure Pt and ZnPt NPs present a very similar activity towards CO oxidation, in contrast with what is reported in a single crystal study. The present study demonstrates the effectiveness of NAP-XPS in the study of complex catalytic processes at work on nanocatalysts under near-ambient pressures, and highlights once more the difficulty of transposing single crystal surface observations to the case of nanoobjects.

How a tertiary diamine molecule chelates the silicon dimers of the Si(001) surface: a real-time scanning tunneling microscopy study.

The patterning of silicon surfaces by organic molecules emerges as an original way to fabricate innovative nanoelectronic devices. In this regard, we have studied how a diamine, N,N,N',N'-tetramethylethylenediamine (TMEDA, (CH3)2N-[CH2]2-N(CH3)2), chelates the silicon dimers of the Si(001)-2 × 1 surface. Starting from very low coverage to surface saturation (at 300 K), we used real-time scanning tunneling microscopy (STM) in a scanning-while-dosing approach. The images show that the molecules can adopt two bonding configurations: the cross-trench (CT) configuration by bridging two adjacent dimer rows, and the end-bridge (EB) configuration by chelating two adjacent dimers in the same row. However, while CT dominates over EB at low coverage, the percentage of EB adducts steadily increases, until it becomes largely dominant at high molecular coverage. Above a critical coverage θmol of ∼0.13 monolayer (ML), a sudden change in the molecular imprints is seen, likely due to a change in the tunneling conditions. The EB stapling of two adjacent dimers in a row via a dual-dative bond (as shown by XPS) is achieved efficiently by the TMEDA molecule with a very high chemical selectivity. The EB is a unique configuration in amine adsorption chemistry, as it leads to the formation of a pair of first-neighbor, doubly-occupied dangling bonds. Further reactivity of the EB site with other molecules remains to be explored, and possible reaction schemes are envisaged.

Energy-Level Alignment of a Hole-Transport Organic Layer and ITO: Toward Applications for Organic Electronic Devices.

2,2',6,6'-Tetraphenyl-4,4'-dipyranylidene (DIPO-Ph4) was grown by vacuum deposition on an indium tin oxide (ITO) substrate. The films were characterized by atomic force microscopy as well as synchrotron radiation UV and X-ray photoelectron spectroscopy to gain an insight into the material growth and to better understand the electronic properties of the ITO/DIPO-Ph4 interface. To interpret our spectroscopic data, we consider the formation of cationic DIPO-Ph4 at the ITO interface owing to a charge transfer from the organic layer to the substrate. Ionization energy DFT calculations of the neutral and cationic species substantiate this hypothesis. Finally, we present the energetic diagram of the ITO/DIPO-Ph4 system, and we discuss the application of this interface in various technologically relevant systems, as a hole-injector in OLEDs or as a hole-collector interfacial layer adjacent to the prototypical OPV layer P3HT:PCBM.

Room temperature differential conductance measurements of triethylamine molecules adsorbed on Si(001).

We have measured the differential conductance of the triethylamine molecule (N(CH2CH3)3) adsorbed on Si(001)-2 × 1 at room temperature using scanning tunneling spectroscopy. Triethylamine can be engaged in a dative bonding with a silicon dimer, forming a Si-Si-N(CH2CH3)3 unit. We have examined the datively bonded adduct, either as an isolated molecule, or within an ordered molecular domain (reconstructed 4 × 2). The differential conductance curves, supported by DFT calculations, show that in the explored energy window (±2.5 near the Fermi level) the main features stem from the uncapped dangling bonds of the reacted dimer and of the adjacent unreacted ones that are electronically coupled The formation of a molecular domain, in which one dimer in two is left unreacted, is reflected in a shift of the up dimer atom occupied level away from the Fermi level, likely due to an increased π-bonding strength. In stark contrast with the preceding, pairs of dissociated molecule (a minority species) are electronically decoupled from the dimer dangling bond states. DFT calculation show that the lone-pair of the Si-N(CH2CH3)2 is a shallow level, that is clearly seen in the differential conductance curve.

Propanoate grafting on (H,OH)-Si(0 0 1)-2 × 1.

We have examined the reactivity of water-covered Si(0 0 1)-2 × 1, (H,OH)-Si(0 0 1)-2 × 1, with propanoic (C2H5COOH) acid at room temperature. Using a combination of spectroscopic techniques probing the electronic structure (XPS, NEXAFS) and the vibrational spectrum (HREELS), we have proved that the acid is chemisorbed on the surface as a propanoate. Once the molecule is chemisorbed, the strong perturbation of the electronic structure of the hydroxyls, and of their vibrational spectrum, suggests that the molecule makes hydrogen bonds with the surrounding hydroxyls. As we find evidence that surface hydroxyls are involved in the adsorption reaction, we discuss how a concerted or a radical-mediated reaction (involving the surface silicon dangling bonds) could lead to water elimination and formation of the ester.

Surface reactions of 3-butenenitrile on the Si(001)-2 x 1 surface at room temperature.

Using a combination of local -- scanning tunneling microscopy -- and spatially integrated, but chemically sensitive probes -- X-ray photoelectron spectroscopy and near edge X-ray absorption fine structure spectroscopy -- we have examined how 3-butenenitrile reacts with the Si(001)-2 x 1 surface at room temperature. Electron spectroscopies indicate three different nitrogen chemical bonds: a Si-C=N-Si bond, a C=C=N cumulative double bond, and a CN moiety datively bonded to a silicon atom. All molecular imprints detected by scanning tunneling microscopy (STM) involve two adjacent silicon dimers in the same row. The three geometries we propose -- a double di-sigma bonding via the CN and the C=C, a cumulative double bond formation associated with alphaC-H bond dissociation, and a di-sigma vinyl bonding plus a CN datively bonded to a silicon atom -- are all compatible with electron spectroscopies and data. Real-time Auger yield kinetic measurements show that the double di-sigma bonding geometry is unstable when exposed to a continuous flux of 3-butenenitrile molecules, as the Si-C=N-Si unit transforms into a CN moiety. A model is proposed to explain this observation.