Bar adsorptive microextraction coated with multi-walled carbon nanotube phases - Application for trace analysis of pharmaceuticals in environmental waters.

Bar adsorptive microextraction devices were modified with multi-walled carbon nanotubes for the first time. A bar adsorptive microextraction method followed by microliquid desorption and high-performance liquid chromatography with diode array detection was developed for the determination of trace levels of ketoprofen, diclofenac, gemfibrozil and mefenamic acid in water samples. The mean parameters affecting the bar adsorptive microextraction and microliquid desorption efficiency were studied and optimized using a univariate optimization strategy. The methodology was validated in terms of linearity, limits of detection and quantification, recovery, intra- and inter-day precision, accuracy, and matrix effect. The developed method showed lower limits of quantification of 0.35 µg L-1, calibration curves from 0.35 up to 1000.0 µg L-1 and determination coefficients higher than 0.9917. Recoveries in tap, surface, sea and waste water samples at three spiking levels were between 70.2 and 117.3% for all the pharmaceuticals. The coefficients of variation values for intra- (n = 6) and inter-day precisions (n = 18) were below 9.7%. The proposed analytical methodology allowed preconcentration factors up to 250 and proved to be cost-effective, easy to operate and environmentally friendly.

Mercury species accumulation and trophic transfer in biological systems using the Almadén mining district (Ciudad Real, Spain) as a case of study.

The impact of mercury (Hg) pollution in the terrestrial environments and the terrestrial food chains including the impact on human food consumption is still greatly under-investigated. In particular, studies including Hg speciation and detoxification strategies in terrestrial animals are almost non-existing, but these are key information with important implications for human beings. Therefore, in this work, we report on Hg species (inorganic mercury, iHg, and monomethylmercury, MeHg) distribution among terrestrial animal tissues obtained from a real-world Hg exposure scenario (Almadén mining district, Spain). Thus, we studied Hg species (iHg and MeHg) and total selenium (Se) content in liver and kidney of red deer (Cervus elaphus; n = 41) and wild boar (Sus scrofa; n = 16). Similar mercury species distribution was found for both red deer and wild boar. Major differences were found between tissues; thus, in kidney, iHg was clearly the predominant species (more than 81%), while in liver, the species distribution was less homogeneous with a percentage of MeHg up to 46% in some cases. Therefore, Hg accumulation and MeHg transfer were evident in terrestrial ecosystems. The interaction between total Se and Hg species has been evaluated by tissue and by animal species. Similar relationships were found in kidney for both Hg species in red deer and wild boar. However, in liver, there were differences between animals. The possible underlying mechanisms are discussed.

Comparative study of mercury speciation in commercial fishes of the Brazilian Amazon.

Mercury is responsible for serious episodes of environmental pollution throughout the world, especially in the Amazon. This toxicity has led regulatory agencies to focus on fish as the target organism for protecting the health of humans and other sensitive organisms. Unfortunately, in the Amazon area, different sampling strategies and the wide variety of sampling areas and fish species make it extremely difficult to determine relationships across geographic regions or over time to ascertain historical trends. Thus, the aim of this work was to achieve three main objectives: a comparative study of mercury contamination in fish of Itaituba (Tapajós, located downstream of the largest gold-mining region in Amazon) and Belém (an area non-exposed to mercury pollution of anthropogenic origin), perform an analysis of inorganic mercury (IHg) versus monomethylmercury (MeHg) contents, and, finally, compare mercury contamination in Tapajós over time. Five piscivorous species were obtained in Itaituba and Belém. Also, four non-piscivorous species were collected in Itaituba. For the first time, mercury speciation showed that (1) current MeHg levels in piscivorous species in Tapajós are higher than those of the non-exposed area, (2) piscivorous species from Itaituba (dourada, filhote, and sarda) contained mercury levels above the World Health Organization safety limit (~17%) and/or above the US Environmental Protection Agency tissue residue criterion (40%), (3) increased MeHg is usually accompanied by increased IHg, and (4) the mean total mercury concentrations for piscivorous species in Itaituba were within the same range and, associated uncertainties as those previously reported, although a remarkable decreasing trend over time was observed for mean total Hg concentrations in non-piscivorous species from Itaituba. The present study supports the importance of continuous monitoring of both populations in the Amazon Rivers. Our results will better assist the development of preventive strategies and governmental actions to confront the problem of mercury contamination in the Amazon.

Mercury speciation analysis in terrestrial animal tissues.

No previous analytical procedures are available and validated for mercury speciation analysis in terrestrial animal tissues. This analysis is a difficult task both because the expected concentrations are low, since important accumulation process are not likely to occur, and also because there are not commercially available certified reference material. Thus, an analytical methodology has been developed and validated for mercury speciation for the specific case of terrestrial animal tissues. The proposed method is based on the quantitative extraction of the species by closed-vessel microwave assisted heating with an alkaline reagent, followed by ethylation. The ethylated derivatives were then submitted to head-space solid phase microextraction with a 100 µm polidimethylsiloxane-coated fiber, and desorbed onto a gas chromatograph coupled to atomic fluorescence detection via pyrolysis unit (HS-SPME-GC-pyro-AFS). Procedural detection limits were 31.8 ng g(-1) and 52.5 ng g(-1) for CH(3)Hg(+) and Hg(2+), respectively, for liver and 35.3 ng g(-1) and 58.1 ng g(-1) for CH(3)Hg(+) and Hg(2+), respectively, for kidney. These limits of detection are 5.5 and 6 times better than the obtained without solid phase microextraction for CH(3)Hg(+) and Hg(2+), respectively. The methodology was found linear up to 120 µg L(-1) and reproducible from one day to the following. It was validated with certified reference materials NCS ZC 71001 (beef liver) and BCR No 186 (pig kidney) for total mercury, calculated as the sum of species, and with spiked red deer liver and kidney for speciation. Finally, it was applied to the analysis of samples of red deer liver, red deer kidney and wild boar kidney coming from the Almadén's mercury mining area (Ciudad Real, Spain), the longest and largest producer of mercury in the world until its closure in 2002.

Mercury in the Tapajós River basin, Brazilian Amazon: a review.

This paper presents a review about mercury contamination and human exposure in the Tapajós River basin (Brazil), one of the major tributaries of the Amazon impacted by traditional gold mining from the mid 1980s. The most recent review in this region was published more than ten years ago and since then many articles about environment and especially human populations have revealed new aspects of mercury toxicology. Additionally, new biomarkers of mercury exposure and toxicity have been studied in these populations. However, there are still many open, about both mercury's biogeochemical cycle and mercury health risks. Further environmental and human risk research directions are proposed.

Integrated pollution evaluation of the Tagus River in Central Spain.

The aim of this study was to integrate hydrochemical and sediment data in order to obtain a picture of the pollution state of the Tagus River along central Spain. This area is of special interest because tributaries from the Madrid region are discharged and no previous data were available. Waters and sediments were sampled between 2002 and 2004 from selected sites before and after Jarama River confluence (Madrid city input). The samples were analysed for more than 50 parameters, including those of physico-chemical nature and those reporting the pollution caused by both metals and organic compounds. The quality of waters for different uses has been tested and statistical quality indexes of both global and partial type has also been established. Sediments pollution state was evaluated by comparison with general quality standards. A high degree of pollution and general degradation was observed in the Tagus River downstream the Jarama River input. The pollution of waters is mainly related to parameters indicators of organic pollution from urban sewage. In sediments, a dramatic increase in the concentration of trace metals was found in different points, exceeding toxicological threshold. Further studies would be necessary for organic pollutants and also to evaluate the remobilization potential.

Determination of monomethylmercury in low- and high-polluted sediments by microwave extraction and gas chromatography with atomic fluorescence detection.

The analysis of monomethylmercury (MMHg) in sediments is a difficult task because both very low concentrations and interconversion between species especially in highly polluted samples are frequent. This work features a general strategy for real sediment analysis with preconcentration and/or clean-up steps for both low- and high-polluted sediments to control these specific problems. The extraction conditions have been optimized using closed-vessel microwave-assisted heating with acidic extractants. The analysis has been carried out by the injection of ethylated derivatives of the analytes into a capillary gas chromatographic system coupled to fluorescence spectrometry. When using 6M HNO3, the most labile inorganic mercury fraction as well as MMHg were extracted from the sediment but there was still some inorganic mercury that remained un-extracted. MMHg was stable and quantitatively recovered by applying this procedure. The role of the labile inorganic fraction on artifact MMHg generation has been evaluated and it has been found to be highly variable depending on the sediments' geochemical characteristics. Therefore, for high-polluted sediments (inorganic mercury concentration above 500 ngg(-1)) a clean-up step with dichloromethane has been used before ethylation, whereas for low content samples, preconcentration under nitrogen stream at room temperature has been optimized. Both steps can be combined if necessary. MMHg content has been found in good agreement with the certified value for the reference materials (IAEA-405 and ERM-CC580).

Improvement of analytical performances for mercury speciation by on-line derivatization, cryofocussing and atomic fluorescence spectrometry.

A modified automated on-line hyphenated system for simultaneous inorganic ionic mercury (Hg(2+)) and monomethylmercury (MeHg(+)) analysis by hydride generation (HG) or ethylation (Eth), cryofocussing, gas chromatography (GC) separation and atomic fluorescence spectrometry (AFS) detection has been improved. Both derivatization methods are investigated with respect to the chromatographic and analytical performances. They can be both affected by interferences when the AFS detection system is used. Water vapor removal using a soda lime moisture trap improves significantly the chromatographic performances, the reproducibility and the detection limits for Hg(2+) and MeHg(+) analyzed with both methods. For ethylation (Eth) derivatization, a scattering interference generated from low-quality ethylation reagent has also been eliminated. For HG, improved detection limits are 0.13ngl(-1) and 0.01ngl(-1) for Hg(2+) and MeHg(+), respectively (0.1l water sample), and reproducibility are 5% for Hg(2+) (20ngl(-1)) and MeHg(+) (5ngl(-1)). Improved detection limits for Eth are 0.22ngg(-1) for Hg(2+) and 0.02ngg(-1) for MeHg(+) (1g dry sediment sample) and the reproducibility are 5-6% for Hg(2+) and MeHg(+) (1-2ngg(-1)).

Simultaneous sample preparation and species-specific isotope dilution mass spectrometry analysis of monomethylmercury and tributyltin in a certified oyster tissue.

A rapid, accurate, sensitive, and simple method for simultaneous speciation analysis of mercury and tin in biological samples has been developed. Integrated simultaneous sample preparation for tin and mercury species includes open focused microwave extraction and derivatization via ethylation. Capillary gas chromatography-inductively plasma mass spectrometry (CGC-ICPMS) conditions and parameters affecting the analytical performance were carefully optimized both for species-specific isotope dilution analysis of MMHg and TBT and for conventional analysis of MBT and DBT201Hg-enriched monomethylmercury and 117Sn-enriched tributyltin were used for species-specific isotope dilution mass spectrometry (SIDMS) analysis. As important, accurate isotope dilution analysis requires equilibration between the spike and the analyte to achieve successful analytical procedures. Since the spike stabilization and solubilization are the most critical and time-consuming steps in isotope dilution analysis, different spiking procedures were tested. Simultaneous microwave-assisted spike stabilization and solubilization can be achieved within less than 5 min. This study originally introduces a method for the simultaneous speciation and isotope dilution of mercury and tin in biological tissues. The sample throughput of the procedure was drastically reduced by fastening sample preparation and GC separation steps. The accuracy of the method was tested by both external calibration analysis and species-specific isotope dilution analysis using the first biological reference material certified for multielemental speciation (oyster tissue, CRM 710, IRMM). The results obtained demonstrate that isotope dilution analysis is a powerful method allowing the simultaneous speciation of TBT and MMHg with high precision and excellent accuracy. Analytical problems related to low recovery during sample preparation are thus minimized by SIDMS. In addition, a rapid procedure allows us to establish a performant routine method using CGC-ICPMS technique.

Using speciated isotope dilution with GC-inductively coupled plasma MS to determine and unravel the artificial formation of monomethylmercury in certified reference sediments.

Speciated isotope-dilution mass spectrometry (SID-MS) is claimed to be an absolute method; however, it has been found to be affected by artifact monomethylmercury (MMHg) formation in sediments. The determination of MMHg in sediments was carried out by SID-MS after open-focused microwave extraction. The extracted mercury species were then ethylated and separated by capillary gas chromatography (CGC). Isotope ratios (peak area ratios at different masses) were measured by on-line ICP-MS detection of the CGC-separated compounds. Reproducibility of 202Hg/201Hg isotope ratio measurements were 0.60% for MeEtHg and 0.69% for Et2Hg; for 202Hg/199Hg, 0.43 and 0.46%, respectively, were determined. The absolute detection limits for CGC-ICPMS measurements were better than 26 fg for 202Hg, 20 fg for 201Hg, and 24 fg for 199Hg. For the direct determination of MMHg in sediment reference materials (CRM 580, IAEA 356, and IAEA 405), higher values than the certified were always found. Systematic experiments were carried out to localize the sources of the unintentional abiotic methylmercury formation during analysis. Different spiking and derivatization procedures (either ethylation, propylation, or derivatization by Grignard reagents) were tested. In addition, isotopically enriched inorganic mercury was spiked. The amount of inorganic mercury initially present in the sample was found to be the critical factor that should be known and carefully controlled. A simple solvent extraction technique involving no critical cleanup steps was applied in order to reduce high Hg2+ amounts. The method was applied to the determination of MMHg in sediment reference material IAEA-405 with satisfactory results after organic solvent extraction. The limitations of applicability of the proposed method are evaluated as related to inorganic mercury, organic carbon, and sulfur contents. The results obtained confirmed that available sediment reference materials are adequate to achieve traceable mercury speciation analysis and to detect potential sources of MMHg artifact formation.

Distribution of mercury in the aquatic environment at Almadén, Spain.

The world's largest mercury mine is placed at Almadén, Spain. However, there is a lack of information about the environmental impact of these mining activities in the ecosystem that surrounds this area. The aim of this article is to document the concentration of mercury in waters, sediments and bivalves of the aquatic system impacted by historic mine wastes. Simultaneously, a comprehensive study has been undertaken to characterise this hydrosystem and to determine the influence of some major physico-chemical parameters on the fate of mercury. Samplings were carried out for the last few years. Concentration of mercury in waters ranged from not detectable to 20 microg/l. For the sediments study, samples have been taken both from contaminated and non-contaminated sites within the basin. The regional background mercury concentration is higher than values typically cited for natural backgrounds. At exposed sites the mercury concentrations between 5 and 1000 microg/g were measured. These values are one to four order of magnitude greater than regional background levels. In the comparison between the results obtained at the present moment and those available for the 1974-1977 period, a general diminution of mercury levels is observed. Mercury concentrations in fresh water bivalves ranged between 1 and 4 microg/g (d.w.), with around 30% as monomethylmercury. In the discussion of the implications for risk assessment data available for other areas affected both for mine activities and mercuriferous belt are included.

Application of cryofocusing hydride generation and atomic fluorescence detection for dissolved mercury species determination in natural water samples.

The concentration levels of mercury (Hg) species in natural water samples are usually low. Consequently, accurate analysis with low detection limits is still a major problem. In this work, a method was applied for the simultaneous direct determination of dissolved mercury species in water samples by on-line hydride generation (HG), cryogenic trapping (CT), gas chromatography (GC) and detection by atomic fluorescence spectrometry (AFS). The suitability of the method for real samples with different organic matter and chloride contents was evaluated by recovery experiments in synthetic and natural spiked water samples. The HG method was compared with other current available methods for mercury analysis with respect to the different fraction of mercury analysed, i.e. 'reactive', 'reducible' or total. HG derivatization and SnCl2 reduction (with and without previous oxidation with BrCl) were applied to synthetic and natural (spiked and non-spiked) water samples. The influence of chloride and dissolved organic matter concentrations was studied. The results suggest that the HG procedure is suitable for the simultaneous determination of Hg2+ and MeHg+ in surface water samples. Inorganic mercury analysed by HG (i.e. reducible) is close to the total inorganic mercury.

Application of isotopically labeled methylmercury for isotope dilution analysis of biological samples using gas chromatography/ICPMS.

An isotope dilution (ID) procedure for the determination of methylmercury (MMHg) in biological samples using an inductively coupled plasma mass spectrometer as detector after the capillary gas chromatographic separation (CGC/ICPMS) has been developed. For the first time, open-focused-microwave pretreatment has been used in conjunction with ID. Optimum conditions for the measurement of isotope ratios on the fast transient chromatographic peaks have been established. Mass bias was found to be about 1.5%/mass unit and was corrected by using the simultaneously measured thallium signals at 203Tl and 205Tl. After mass-bias correction, deviation of the theoretical mercury ratio values was found to be as low as 0.2%. Isotope ratio precisions based on the peak areas measurements were 0.3% RSD for 20 pg injected (as Hg absolute). The absolute detection limits were in the range of 20-30 fg for 202Hg and 201Hg. Methylmercury enriched in 201Hg has been synthesized by direct reaction with methylcobalamine. The concentration of the MMHg spike has been measured by reverse isotope dilution with a natural MMHg standard. The capabilities of CGC/ICPMS to measure isotope ratios were used to optimize sample derivatization by aqueous ethylation with NaBEt4 with respect to MMHg degradation pathways and quantitative recovery. The accuracy of the method developed has been validated with biological certified reference materials (CRM-463, DORM-1).