Comparison of Wood-Based Biocomposites with Polylactic Acid (PLA) Density Profiles by Desaturation and X-ray Spectrum Methods.

Wood-plastic composites (WPCs) represent composite materials that employ shredded wood combined with a thermoplastic substance, such as polylactic acid (PLA), to establish structural cohesion within the product profile. This amalgamation of materials results in a robust structure designed to fulfill specialized roles under the influence of pressure and temperature. Given the nature of the constituent materials, the resultant product can be classified as a biocomposite. The creation of such biocomposites entails a rigorous process necessitating the fine-tuning of specific parameters and suitable technologies. The foundational materials employed in this process must be both natural and biodegradable. However, it is noteworthy that natural components like fibers exhibit anisotropic behavior, wherein their mechanical attributes are contingent on the direction of the applied force. Consequently, predicting their performance during biocomposite production proves challenging. The principal objective of this study was to conduct a comparative analysis of wood-based composites incorporating PLA thermoplastic binding agents. The intention was to discern variations in density profiles arising from distinct measurement methodologies. Two measurement methods were used for the measurement: X-ray and spectrum desaturation. Additionally, the study sought to investigate the impact of introducing PLA additives at 25% and 50% concentrations on the fabrication of WPC from wood chips. The properties of these composites were assessed by considering the inherent traits of the composite materials.

The Effects of Seawater Treatment on Selected Coniferous Wood Types.

The mechanical strength of wood from Scots pine (Pinus sylvestris), European larch (Larix decidua), and Norway spruce (Picea abies) was studied using static compression tests. The material was exposed under constant soaking in water with salinity of 7‱. The liquid mix was prepared according to a value roughly equivalent to the average salinity along the entire length of the Baltic Sea. The mechanical strength and quality of the raw material were determined using a sea salt saturation test, which determined the adhesion of the raw material to the extrusion process (permissible stress). An investigation was conducted to determine the physicochemical parameters of the material that was tested. It was investigated how much mineral compounds were absorbed over four cycles lasting a total of six weeks during the test. According to the statistical analysis, the chemical composition of wood and the presence of salts and mineral compounds correlated with its mechanical strength. An important part of the study focused on examining the factors affecting the construction of coniferous wood structures. The preparation of the raw material correctly can provide information on how the material can be protected during exposure to specific environmental conditions for longer.

Effect of Seawater with Average Salinity on the Moisture Content, Ash Content and Tensile Strength of Some Coniferous Wood.

In this paper, the differences in mechanical strength tested during the static tensile and compression test of Scots pine (Pinus sylvestris L.), European larch (Larix decidua) and Norway spruce (Picea abies) wood exposed to continuous soaking in water with a salinity of 7‱ were determined. The value of salinity corresponded to the average salinity on the Polish Baltic coast. This paper also aimed to examine the content of mineral compounds absorbed during four cycles of two weeks each. The essence of the statistical research was to identify the effect of the mineral range compounds and salts depending on the mechanical strength of the wood. Based on the results of the experiments, it can be concluded that the medium used has a specific effect on the wood species' structure. The effects of soaking on the wood parameters depend obviously on the type of wood. A tensile strength test of pine, as well as the tensile strength other species, was enhanced by incubating it in seawater. A native sample's initial mean tensile strength was 82.5 MPa, which increased to 94.8 MPa in the last cycle. It was found that the larch wood had the lowest tensile strength difference (9 MPa) of the woods studied in the current study. Four to six weeks of soaking was necessary to notice an increase in tensile strength.

Dispersed Power Production in Terms of the Potential of Briquettes Made from Straw and Willow as Renewable Sources of Energy.

The rapid development of agricultural technologies has triggered new possibilities of using plant waste as fuel. Briquetting plant material is one of the methods of using crop residue as permanent energy carriers. Nevertheless, to maintain the normalised properties of briquettes, their small-scale production should follow an established and well-considered deliberate technological process limiting production costs. The material to be used for energy production should, in particular, be pre-prepared in terms of crushing and moisture content to ensure the right product parameters. The article aims to provide an analysis of briquettes with varied physicochemical parameters to determine and order homogenous groups for selected parameters characteristic for briquettes made from various bioenergy materials. The specific aim of the article required a statistical analysis as a tool for separating the selected factors. An analysis of variance (ANOVA) was involved, together with a post-hoc Duncan test. The analyses demonstrated that the briquette composition, such as bulk value, moisture, and ash content can enhance the briquette quality. In discussion, the straw used was compared with other kinds of agricultural biomass samples and considerable differences were identified. The chemical analysis showed a high content of carbon (from 42.64 to 45.66%) and oxygen (from 47.60 to 49.68%). The percentage share of hydrogen in the chemical structure of the materials accounted for approximately 6%. The ash content found while investigating various straw types ranged from 3.67 to 4.26%, making it lower than reported in the literature. The study also looked at the energetic potential of straw and wood biomass. It was noticed that bioenergetic sources are much potentially higher than the materials used in the traditional power sector. Especially where it concerns an unlimited source that can be provided to the bio-energetic sector. The study is intended to focus the future energy sector on the use of bioenergy in terms of applying straw to energy production purposes.

Emission of harmful gases from animal production in Poland.

The aim of the study was to present the scale of greenhouse gas emissions from animal production, and to provide test results from different housing systems. In three free stall buildings, two with slurry in deep channels and one with cattle in cubicles staying on shallow litter concentration of ammonia and carbon dioxide were measured in summer season by using dedicated equipment from Industrial Scientific Research. Air exchange was calculated on the base of balance carbon dioxide method. This method was used in order to estimate the air flow rate. Concentrations of ammonia and CO2 were measured as the base for air exchange and ammonia emission rates. Ammonia emissions were product of ammonia concentration and air exchange rate. Temperature and relative humidity were measured to establish microclimate conditions in buildings tested to show the overall microclimatic situation in buildings. Differences between ammonia emission rates were observed in both housing systems. The highest ammonia emission rate was equal to 2.75 g·h-1·LU-1 in well-ventilated cattle barn with the largest herd size.