Metrology of infrared superconducting bolometers with a backshort.

We present the detailed metrology of a superconducting Transition-Edge Sensor (TES) absorber-coupled bolometer array bonded to a variable-delay backshort to form an integral field unit. The backshort is shaped as a wedge to continuously vary the electrical phase delay of the bolometer absorber reflective termination across the array. This resonant absorber termination structure is used to define a spectral response over a 4:1 bandwidth in the far-infrared, from ∼30 to 120 µm. The metrology of the backshort-bolometer array hybrid was achieved with a laser confocal microscope and a compact cryogenic system that provides a well-defined thermal (radiative and conductive) environment for the hybrid when cooled to ∼10 K. The results show the backshort free-space delays do not change with cooling. The estimated backshort slope is 1.58 milli-radians and within 0.3% of the targeted value. The sources of error in the free-space delay of the hybrid and optical cryogenic metrology implementations are discussed in detail. We also present measurements of the bolometer's single-crystal silicon membrane topography. The membranes deform and deflect out-of-plane under both warm and cold conditions. Intriguingly, the optically active area of the membranes tends to flatten when cold and repeatably achieve the same mechanical state over many thermal cycles; hence, no evidence for thermally-induced mechanical instability is observed. Most of the cold deformation is sourced from thermally-induced stress in the metallic layers comprising the TES element of the bolometer pixels. These results provide important considerations for the design of ultra-low-noise TES bolometers.

Excess Heat Capacity in Mo/Au Transition Edge Sensor Bolometric Detectors.

Excess heat capacity in a bolometric detector has the consequence of increasing or leading to multiple device time constants. The Mo/Au bilayer transition edge sensor (TES) bolometric detectors initially fabricated for the high resolution mid-infrared spectrometer (HIRMES) exhibited two response thermalization scales, one of which is a few times longer than estimates based upon the properties of the bulk materials employed in the design. The relative contribution of this settling time to the overall time response of the detectors is roughly proportional to the pixel area, which ranges between ~0.3 and 2.6 mm2. Use of laser ablation to remove sections of the silicon membranes comprising the pixels results in a detector response with a smaller contribution from the secondary time constant. Additional information about the nature of this excess heat capacity is gleaned from glancing incidence x-ray diffraction, which reveals the presence of molybdenum silicides near the silicon surface which is a consequence of the bi-layer deposition. Quantitative analysis of the concentration of excess molybdenum, estimated with secondary ion mass spectroscopy, is commensurate to the additional heat capacity needed to explain the anomalous time response of the detectors.

Impedance matched absorptive thermal blocking filters.

We have designed, fabricated, and characterized absorptive thermal blocking filters for cryogenic microwave applications. The transmission line filter's input characteristic impedance is designed to match 50 Ω and its response has been validated from 0 to 50 GHz. The observed return loss in the 0 to 20 GHz design band is greater than 20 dB and shows graceful degradation with frequency. Design considerations and equations are provided that enable this approach to be scaled and modified for use in other applications.

A waveguide-coupled thermally isolated radiometric source.

The design and validation of a dual polarization source for waveguide-coupled millimeter and sub-millimeter wave cryogenic sensors is presented. The thermal source is a waveguide mounted absorbing conical dielectric taper. The absorber is thermally isolated with a kinematic suspension that allows the guide to be heat sunk to the lowest bath temperature of the cryogenic system. This approach enables the thermal emission from the metallic waveguide walls to be subdominant to that from the source. The use of low thermal conductivity Kevlar threads for the kinematic mount effectively decouples the absorber from the sensor cold stage. Hence, the absorber can be heated to significantly higher temperatures than the sensor with negligible conductive loading. The kinematic suspension provides high mechanical repeatability and reliability with thermal cycling. A 33-50 GHz blackbody source demonstrates an emissivity of 0.999 over the full waveguide band where the dominant deviation from unity arises from the waveguide ohmic loss. The observed thermal time constant of the source is 40 s when the absorber temperature is 15 K. The specific heat of the lossy dielectric, MF-117, is well approximated by C(v)(T) = 0.12 T (2.06) mJ g(-1) K(-1) between 3.5 K and 15 K.