RESUMO
The temperature effect on electronic transport mechanisms in graphene nanoplatelet (GNP) doped polydimethylsiloxane (PDMS) for temperature sensing applications has been investigated under electrical impedance spectroscopy (EIS) analysis. AC measurements showed a very prevalent frequency-dependent behavior in low filled nanocomposites due to the lower charge density. In fact, 4 wt % GNP samples showed a nonideal capacitive behavior due to scattering effects. Therefore, the standard RC-LRC circuit varies with the substitution of capacitive elements by CPEs, where a CPE is a constant phase element which denotes energy dissipation. In this regard, the temperature promotes a prevalence of scattering effects, with an increase of resistance and inductance and a decrease of capacitance values in both RC (intrinsic and contact mechanisms) and LRC (tunneling mechanisms) elements and, even, a change from ideal to nonideal capacitive behavior as in the case of 6 wt % GNP samples. In this way, a deeper understanding of electronic mechanisms depending on GNP content and temperature is achieved in a very intuitive way. Finally, a proof-of-concept carried out as temperature sensors showed a huge sensitivity (from 0.05 to 11.7 °C-1) in comparison to most of the consulted studies (below 0.01 °C-1), proving, thus, excellent capabilities never seen before for this type of application.
RESUMO
Tests on a double lap bonded joint, with transverse strips of randomly oriented carbon nanotubes (CNT) sprayed onto an epoxy adhesive film, showed a positive increment in electrical resistance under tensile load, even though the transverse strains were negative. Other experiments included in this work involved placing longitudinal and transversal CNT sensors in a tensile loaded aluminum plate, and, as reported by other authors, the results confirm that the resistance change is not only dependent on the strains oriented with the electrode line, while the other strain components also influence the response. This behavior is quite different to that of conventional strain gages which have a near zero sensitivity to strains not aligned to the sensor direction. The dependence of the electrical response on all the strain components makes it quite difficult, possibly unfeasible, to experimentally determine the individual strain components with this kind of sensors; however, the manufacturing of aligned CNT sensors could deal with this issue.
RESUMO
Polycaprolactone (PCL) is being researched as a self-healing agent blended with epoxy resins by several reasons: low melting point, differential expansive bleeding (DBE) of PCL, and reaction induced phase separation (RIPS) of PCL/epoxy blends. In this work, PCL/epoxy blends were prepared with different PCL ratios and two different epoxy networks, cured with aliphatic and aromatic amine hardeners. The curing kinetic affects to the blend morphology, varying its critical composition. The self-healing behavior is strongly affected by the blend morphology, reaching the maximum efficiency for co-continuous phases. Blends with dispersed PCL phase into epoxy matrix can also show high self-healing efficiency because of the low PCL domains that act as reservoir of self-healing agent. In this last case, it was confirmed that the most efficient self-healable blends are one whose area occupied by PCL phase is the largest. These blends remain the good thermal and mechanical behavior of epoxy matrix, in contrast to the worsened properties of blends with bicontinuous morphology. In this work, the self-healing mechanism of blends is studied in depth by scanning electron microscopy. Furthermore, the influence of the geometry of the initial surface damage is also evaluated, affecting to the measurement of self-healing efficiency.
RESUMO
A novel nanoreinforced adhesive film has been developed to detect adhesive deformation and crack propagation along the bonding line by means of the electrical response of the material. Adhesive films were doped by spraying an aqueous dispersion of carbon nanotubes (CNTs) over the surface. To determine the sensitivity of bonded joints, single lap shear (SLS) and mode-I fracture energy tests have been carried out while their electrical response has been measured. It has been found that CNT-doped adhesive films are able to detect adhesive deformation and final failure for SLS specimens and crack initiation and propagation along the bonding line for mode-I specimens with a high sensitivity. Sudden increases on electrical resistance are correlated to a rapid growing of the crack length due to instability on crack propagation in a tick-slip case, whereas specimens with a more uniform crack propagation are linked to a steadier increase on electrical resistance, and both of them are properly correlated to the mechanical response. By analyzing more in detail the electrical response and comparing with theoretical approaches, the stick-slip behavior is associated with the presence of porosity and lack of adhesives because of possible manufacturing issues such as adhesive overflowing. These statements are also validated by microstructural analysis. Therefore, the potential and applicability of the proposed adhesive films for evaluating the structural integrity has been demonstrated.
