Influence of surgical technique, implant shape and diameter on the primary stability in cancellous bone.

Achievement of primary stability during surgical placement of dental implants is one of the most important factors for successful osseointegration depending on various anatomical, surgical and implant-related factors. Resonance frequency analysis (RFA) has been shown as a non-invasive and objective technique for measuring the stability of implants. The aim of this study was to evaluate the effect of some surgical and implant-related factors in enhancing primary stability and to estimate a correlation between RFA and insertion torque (IT) in proximal regions of cow ribs representing cancellous bone. Fifteen implant beds were prepared in the most proximal region of six fresh cow ribs. Ninety implants with three different shapes and two different diameters were placed with two different surgical techniques, and the primary stability was compared using RFA and IT. Significantly higher RFA and IT values were achieved when under-dimensioned drilling was used as the surgical method (P<0·01); significantly higher IT values were obtained with the use of wider implants (P<0·01) and partially conical Astra Tech implants showed the highest IT values (P<0·01). When all the implants were considered, significant correlations between the IT and RFA values were noted (%40·6, P<0·05). Partially conical implants with a wide diameter to be placed with the modified surgical technique proposed appear to be useful in enhancing the primary stability in cancellous bone.

A comparison of single-versus double-row suture anchor techniques in a simulated repair of the rotator cuff: an experimental study in rabbits.

We compared time-dependent changes in the biomechanical properties of single-and double-row repair of a simulated acute tear of the rotator cuff in rabbits to determine the effect of the fixation techniques on the healing process. A tear of the supraspinatus tendon was created in 80 rabbits which were separated into two equal groups. A single-row repair with two suture anchors was conducted in group 1 and a double-row repair with four suture anchors in group 2. A total of ten intact contralateral shoulder joints was used as a control group. Biomechanical testing was performed immediately post-operatively and at four and eight weeks, and histological analysis at four and eight weeks. The mean load to failure in group 2 animals was greater than in group 1, but both groups remained lower than the control group at all intervals. Histological analysis showed similar healing properties at four and eight weeks in both groups, but a significantly larger number of healed tendon-bone interfaces were identified in group 2 than in group 1 at eight weeks (p < 0.012). The ultimate load to failure increased with the number of suture anchors used immediately post-operatively, and at four and eight weeks. The increased load to failure at eight weeks seemed to be related to the increase in the surface area of healed tendon-to-bone in the double-row repair group.

The effect of occlusal contact localization on the stress distribution in complete maxillary denture.

The fracture of acrylic resin dentures is an unresolved problem in removable prosthodontics despite many efforts to determine its cause. Unfavourable occlusion could be playing an important role in the fracture of the denture. The aim of this study was to investigate the effect of occlusal contact localization on the stress distribution in complete maxillary denture bases utilizing two-dimensional finite element analysis. The results of this study have shown that maximum compressive stresses in a complete maxillary denture under functional masticatory forces concentrates always on the artificial tooth/denture base junction irrespective to the occlusal contact localization. Tensile stresses were observed in areas toward the midline, although the midline itself usually had lower stresses. Shifting the occlusal contacts to a more buccal localization resulted in an increase of the calculated stresses. As a conclusion, it can be speculated that the buccal placement of the occlusal contacts may play a role in the fatigue fracture of the complete maxillary denture.

Biomechanical analysis of cervical multilevel oblique corpectomy: an in vitro study in sheep.

BACKGROUND: Anterolateral oblique corpectomy is an alternative approach to treatment of multilevel cervical spinal disease. It is stated that the approach does not cause instability in the patients with hard discs, so fusion or instrumentation is not required. The authors undertook a study on stability of the cervical spine by an animal model to establish if this approach causes instability. MATERIAL AND METHODS: Thirty-seven C3 to C6 spinal segments obtained from 3 to 4-year-old male sheep were used. In vitro maximal loading values were obtained from seven sheep cervical specimens for flexion, extension, lateral flexion in both directions, axial rotation in both directions and axial loading, and load deformation curves were drawn by an electrohydrolic testing machine. Other specimens were divided into three groups: Control (n=10), C4 (n=10) and C4-5 (n=10) groups. In two study groups, one or two level oblique corpectomies were performed. In the control and study groups, biomechanical tests were obtained according to the maximal loading values. Load-deformation curves were drawn and displacement amounts were determined for all seven movements. RESULTS: No statistically significant differences were observed in load deformation curves and displacement amounts between all three groups for seven movements. CONCLUSION: These results support the opinion that anterolateral oblique corpectomy does not cause cervical instability.