Pickering phase change slurries.

HYPOTHESIS: Phase change slurries (PCS) have emerged as a promising class of oil-in-water emulsions for energy applications, but stability remains an issue. Pickering phase change slurries (PPCS) stabilized solely by nanoparticles could offer enhanced stability. We hypothesize that stability in PPCS can be achieved by tuning environmental variables of salinity and temperature. EXPERIMENTS: A paraffin-based PPCS stabilized using fumed silica nanoparticles was developed and assessed under varying NaCl concentrations (up to 150 mM) and temperatures (up to 70 °C). Extended-DLVO modeling, confocal, and cryogenic electron microscopy analyzed the silica-paraffin interactions. Rheological experiments examined the impact of effective volume fraction, thermal expansion, and salinity on the viscosity and shear stability of PPCS. The stability of the resulting formulation was assessed under high pressure and temperature conditions. FINDINGS: Increased salinity did not change the packing density of the silica at the oil-water interface (82% ± 6%) but did increase the adsorbed layer thickness and network formation, enhancing the formulation's resistance to shear-induced instability. A critical volume fraction of 0.51 ± 0.01 was identified, beyond which viscosity increased significantly. The resulting formulations remained stable under high pressures and temperatures, regardless of salinity. These findings offer insights into the variables affecting PPCS properties, assisting in designing stable PPCS formulations for diverse applications.

Experimental examination of the phase transition of water on silica at 298 K.

The objective of this study was to investigate the prediction of the wetting characteristics obtained from the equilibrium adsorption analysis using the Zeta adsorption isotherm approach with an experimental study. Water vapor's adsorption and wetting characteristics on a hydroxylated and nano-polished silica substrate were studied in near-equilibrium conditions at temperatures near 298 K. Using a UV-visible interferometer, water vapor adsorbate film thicknesses were measured and converted into amount adsorbed per unit area. The current results show that the wetting transition occurred at an average subcooling value of 0.39 K, less than the predicted value of 0.49 K. All the different experimental observations showed growth of film thickness as a function of subcooling value with a maximum film thickness of 12.6 nm. The analysis of the results further showed that the maximum stable film was in a metastable state that then condensed in a dropwise manner, if perturbed by increasing the subcooling. The study further revealed that the adsorbate is unstable after transitioning. The solid surface energy calculated by including the near-equilibrium observations was comparable and close to that of the equilibrium studies, thus supporting solid surface energy as a material property.

Rheological Behavior of Phase Change Slurries for Thermal Energy Applications.

Phase change materials that leverage the latent heat of solid-liquid transition have many applications in thermal energy transport and storage. When employed as particles within a carrier fluid, the resulting phase change slurries (PCSs) could outperform present-day single-phase working fluids─provided that viscous losses can be minimized. This work investigates the rheological behavior of encapsulated and nonencapsulated phase change slurries (PCSs) for applicability in flowing thermal energy systems. The physical and thermal properties of the PCS candidates, along with their rheological behavior, are investigated below and above their phase transition points at shear rates of 1-300 s-1, temperatures of 20-80 °C, and concentrations of 15-37.5 wt %. The effect of shell robustness and melting on local shear thickening and global shear thinning is discussed, followed by an analysis of the required pumping power. A hysteresis analysis is performed to test the transient response of the PCS under a range of shear rates. We assess the complex viscoelastic behavior by employing oscillatory flow tests and by delineating the flow indices─flow consistency index (K) and flow behavior index (n). We identify a viscosity limit of 0.1 Pa·s for optimal thermal performance in high-flow applications such as renewable geothermal energy.

3D and 4D printing in dentistry and maxillofacial surgery: Printing techniques, materials, and applications.

3D and 4D printing are cutting-edge technologies for precise and expedited manufacturing of objects ranging from plastic to metal. Recent advances in 3D and 4D printing technologies in dentistry and maxillofacial surgery enable dentists to custom design and print surgical drill guides, temporary and permanent crowns and bridges, orthodontic appliances and orthotics, implants, mouthguards for drug delivery. In the present review, different 3D printing technologies available for use in dentistry are highlighted together with a critique on the materials available for printing. Recent reports of the application of these printed platformed are highlighted to enable readers appreciate the progress in 3D/4D printing in dentistry.