Viscosity measurement dataset for a water-based drilling mud-carbon nanotube suspension at high-pressure and high-temperature.

This data article presents the measured viscosity of a carbon nanotube (CNT) suspension in water-based drilling mud, also termed as nano-muds ("Rheology of a colloidal suspension of carbon nanotube particles in a water-based drilling fluid" Anoop et al., 2019). The apparent viscosity values of the nano-mud samples are measured using a high-pressure high-temperature viscometer at different shear rates, working based on a rotor and bob technique. The pressure and temperature of the samples are independently varied during the measurements from ambient conditions to 171 MPa and 176 °C, respectively, within two experimental schedules. Viscosity measurements for varying nanoparticle concentration, shear rate, pressure, and temperature are reported here for different CNT concentrations.

Dynamic Flow Characteristics and Design Principles of Laminar Flow Microbial Fuel Cells.

Laminar flow microbial fuel cells (MFCs) are used to understand the role of microorganisms, and their interactions with electrodes in microbial bioelectrochemical systems. In this study, we reported the flow characteristics of laminar flow in a typical MFC configuration in a non-dimensional form, which can serve as a guideline in the design of such microfluidic systems. Computational fluid dynamics simulations were performed to examine the effects of channel geometries, surface characteristics, and fluid velocity on the mixing dynamics in microchannels with a rectangular cross-section. The results showed that decreasing the fluid velocity enhances mixing but changing the angle between the inlet channels, only had strong effects when the angle was larger than 135°. Furthermore, different mixing behaviors were observed depending on the angle of the channels, when the microchannel aspect ratio was reduced. Asymmetric growth of microbial biofilm on the anode side skewed the mixing zone and wall roughness due to the bacterial attachment, which accelerated the mixing process and reduced the efficiency of the laminar flow MFC. Finally, the magnitude of mass diffusivity had a substantial effect on mixing behavior. The results shown here provided both design guidelines, as well as better understandings of the MFCs due to microbial growth.

Prediction of Microdroplet Breakup Regime in Asymmetric T-Junction Microchannels.

Splitting droplets is becoming a major functional component in increasing number of droplet microfluidic applications, and there is an increasing interest in splitting droplets into two daughter droplets with different volumes. However, designing an asymmetric droplet splitter and predicting how a droplet splits in such designs is not trivial. In this study, numerical simulations were conducted to study droplet breakup in asymmetric T-junctions of square cross-sections having different pressure gradient ratios (i.e. T-junctions with outlet branches of different lengths). The goal of the simulation is to identify the conditions where a parent droplet breaks or does not break into two smaller droplets of different sizes (so called critical condition) and to identify the important fluid and microchannel parameters in this process. Four modes of droplet breakup (primary-, transition-, bubble-, and non-breakups) are identified and an empirical correlation is introduced that can predict the breakup/non-breakup of the droplet based on the parent droplet size and the capillary number. The simulation results are then compared with experimental data to verify its accuracy and the effect of fluids properties on the proposed correlation are studied. Two major asymmetric breakup mechanisms are determined, namely "breakup with permanent obstruction" and "unstable breakup". The numerical results show that the splitting ratio for the asymmetric breakup mechanisms depends on flow conditions and dwell time of the droplet at the junction prior to splitting. Finally, the results from two-dimensional and three-dimensional simulations were compared. It is shown that two-dimensional simulation may not accurately predict the breakup behavior for asymmetric droplet breakup and viscosity ration has a greater effect on the prediction critical condition.

nPIV velocity measurement of nanofluids in the near-wall region of a microchannel.

Colloidal suspensions of nano-sized particles in a base fluid, nanofluids, have recently gained popularity as cooling fluids mainly due to their enhanced heat transfer capabilities. However, there is controversy in the literature on the reported properties of nanofluids and their applicability, especially since there is no fundamental understanding that explains these enhancements. A better understanding of these fluids and how they interact with a solid boundary may be achieved by a detailed near-wall fluid flow study at nanoscale. This work presents for the first time the near-wall velocity measurements for nanofluids using nanoparticle image velocimetry. This novel technique uses evanescent illumination in the solid-fluid interface to measure near-wall velocity field with an out-of-plane resolution on the order of O(100 nm). Nanofluids of different concentrations were prepared by dispersing silicon dioxide particles (10 to 20 nm) in water as the base fluid. Initially, viscosity measurements were conducted for the prepared nanofluids. The near-wall velocity data were then measured and compared with that of the base fluid at the same flow condition. It was observed that even though nanofluid viscosity had increased with particle loading, the near-wall velocity values were similar to that of the base fluid for a given flow rate. Together, these measurements vindicate the homogenous and Newtonian characteristics of the nanofluids in the near-wall region. Despite the low particle concentrations investigated, the present work also discusses the complexity involved in utilizing the methodology and possible errors arising during experimentation so as to implement this measurement tool more effectively in the future.