Ultrathin wide band gap kesterites.

Kesterite Cu2ZnSnS4 (CZTS), used for thin film solar cells, has a band gap energy around 1.5-1.6 eV with possibilities for further increase through alloying. In some applications for wide band gap solar cells, reduced absorber thickness can be beneficial, to allow partial light transmission. Reduced thickness can also be beneficial to reduce bulk recombination, and so called ultrathin solar cells (<700 nm thick) have been studied for several materials systems. Here, we report performance for CZTS devices down to 250 nm thickness and show that performance loss from thickness reduction is relatively small, partly due to short minority carrier diffusion length. Insertion of thin passivation layers (Al2O3, SiO2 or HfO2) at the Mo/CZTS interface gives improved performance of ultrathin devices, from 4.7% to 5.6% efficiency for best performing cells having 250 nm thick CZTS with Mo as compared to Mo/Al2O3 back contact. The approach of NaF post deposition for making isolating passivation layers conductive is tested for the first time for CZTS and is shown to work. For fabrication of CZTS devices on transparent ITO back contact, the insertion of passivation layers can reduce diffusion of indium into CZTS, but device performance is lower than on Mo back contacts.

Gettering in PolySi/SiOx Passivating Contacts Enables Si-Based Tandem Solar Cells with High Thermal and Contamination Resilience.

Multijunction solar cells in a tandem configuration could further lower the costs of electricity if crystalline Si (c-Si) is used as the bottom cell. However, for direct monolithic integration on c-Si, only a restricted number of top and bottom cell architectures are compatible, due to either epitaxy or high-temperature constraints, where the interface between subcells is subject to a trade-off between transmittance, electrical interconnection, and bottom cell degradation. Using polySi/SiOx passivating contacts for Si, this degradation can be largely circumvented by tuning the polySi/SiOx stacks to promote gettering of contaminants admitted into the Si bottom cell during the top cell synthesis. Applying this concept to the low-cost top cell chalcogenides Cu2ZnSnS4 (CZTS), CuGaSe2 (CGSe), and AgInGaSe2 (AIGSe), fabricated under harsh S or Se atmospheres above 550 °C, we show that increasing the heavily doped polySi layer thickness from 40 to up to 400 nm prevents a reduction in Si carrier lifetime by 1 order of magnitude, with final lifetimes above 500 µs uniformly across areas up to 20 cm2. In all cases, the increased resilience was correlated with a 99.9% reduction in contaminant concentration in the c-Si bulk, provided by the thick polySi layer, which acts as a buried gettering layer in the tandem structure without compromising the Si passivation quality. The Si resilience decreased as AIGSe > CGSe > CZTS, in accordance with the measured Cu contamination profiles and higher annealing temperatures. An efficiency of up to 7% was achieved for a CZTS/Si tandem, where the Si bottom cell is no longer the limiting factor.

Comparison of micro column technology with conventional tube methods for antibody detection.

BACKGROUND AND OBJECTIVES: Conventional tube technique (CTT) has been the mainstay for antibody detection in pretransfusion testing. There have been rapid technological advances in blood banking and methodology of crossmatch has been modified to improve the sensitivity of these tests and to enable automation. This study was done to compare the efficacy of three crossmatch techniques: CTT, tube low-ionic-strength-saline indirect antiglobulin test (tube LISS-IAT), and micro column technology (MCT) used in the blood bank serology laboratory. MATERIALS AND METHODS: In this prospective study, 150 samples from patients who had received two or more transfusions on two different occasions (with at least 72 h between two transfusions) were subjected to cross match by three different techniques - CTT, LISS-IAT, and MCT. RESULTS: A total of 16 cases with antibodies were identified in 150 patients. Out of 16 cases, 14 were clinically significant (anti-c = 5, anti-K = 4, anti-E = 2, anti-S = 2, anti-Jka = 1) and 2 nonclinically significant antibody cases (anti-Lea). MCT detected all the 14 clinically significant antibody cases and no case of nonclinically significant antibody. Tube LISS-IAT detected 14 antibody cases including 2 cases of non-clinically significant antibody but failed to detect 1 case of anti-c and the only case of anti-Jka. CTT detected only 10 antibody cases including 2 cases of non-clinically significant antibody and but failed to detect 3 cases of anti-c, 1 case of anti-K, 1 case of anti-E, and the only case of anti-Jka. CONCLUSION: MCT was found to be most efficacious when compared to CTT and tube LISS-IAT in detecting clinically significant red cell antibodies; although MCT missed 2 cases of Lea antibody which were detected by CTT and LISS-IAT.

Assessment of changes in plasma hemoglobin and potassium levels in red cell units during processing and storage.

Red cell units undergo changes during storage and processing. The study was planned to assess plasma potassium, plasma hemoglobin, percentage hemolysis during storage and to determine the effects of outdoor blood collection and processing on those parameters. Blood collection in three types of blood storage bags was done - single CPDA bag (40 outdoor and 40 in-house collection), triple CPD + SAGM bag (40 in-house collection) and quadruple CPD + SAGM bag with integral leukoreduction filter (40 in-house collection). All bags were sampled on day 0 (day of collection), day 1 (after processing), day 7, day 14 and day 28 for measurement of percentage hemolysis and potassium levels in the plasma of bag contents. There was significant increase in percentage hemolysis, plasma hemoglobin and plasma potassium level in all the groups during storage (p < 0.001). No significant difference was found between any parameter analyzed for outdoor and in-house collected single CPDA red cell units. There was significant lower percentage hemolysis (p < 0.001) and potassium (day 7 to day 14 - p < 0.05 and day 14 to day 28 - p < 0.001) in red cell units from day 7 onward until day 28 of storage in the leukoreduced quadruple bag as compared to the triple bag. The in-house single CPDA red cell units showed significantly more hemolysis (p < 0.001) as compared to the triple bags with SAGM additive solution after 28 days of storage. There is gradual increase in plasma hemoglobin and plasma potassium levels during the storage of red blood cells. Blood collection can be safely undertaken in outdoor blood donation camps even in hot summer months in monitored blood transport boxes. SAGM additive solution decreases the red cell hemolysis and allows extended storage of red cells. Prestorage leukoreduction decreases the red cell hemolysis and improves the quality of blood.