Properties and Performance of Epoxy Resin/Boron Acid Composites.

This research study focused on the effect of adding boric acid to epoxy resin in order to obtain a composite material with improved properties and performance. To this end, a fine powder of boric acid (H3BO3) was introduced into epoxy resin in different amounts, i.e., 0.5 g, 1.0 g, and 1.5 g. As the matrix of the epoxy composites, styrene-modified epoxy resin based on bisphenol A (BPA) (Epidian 53) was used. It was cross-linked with two types of curing agents, i.e., an amine (ET) and a polyamide (PAC). The mechanical properties of the obtained epoxy composites (in terms of compressive strength, compressive modulus, and compressive strain) were determined at room temperature in order to assess the effect of the addition of boron acid and of the type of curing agent employed to cure the epoxy on these characteristics. Calorimetric measurements were made to highlight any changes in the glass transition temperature (Tg) as a result of the addition of boric acid to epoxy resin. Finally, flammability tests were performed on both Epidian 53/PAC and Epidian 53/ET epoxy composites to analyze their fire behavior and consequently establish the effectiveness of the selected additive as a flame retardant.

Physical Properties of Eco-Sustainable Form-Stable Phase Change Materials Included in Mortars Suitable for Buildings Located in Different Continental Regions.

Starting from two low-cost, low-environmental-impact polymers belonging to the Polyethylene Glycol (PEG) family, i.e., PEG 800 and PEG 1000, two form-stable phase change materials were produced. The two PEGs differ in molecular weight and, as a consequence, the melting and crystallization range of temperatures. The PCMs were obtained, including the PEG, in a liquid state, inside the pores of Lecce Stone flakes, obtained as waste pieces from its processing. A simple and inexpensive impregnation process was selected to produce the PCMs, thus adopting low-environmental-impact materials and cheap processes, and respecting circular economy principles. The two PCMs, the first composed of PEG 800, namely LS/PEG800, and the second composed of a 50/50%wt. mix of the different LS/PEGs, i.e., LS/PEG800_LS/PEG1000, were added as aggregates to four types of mortars, based on aerial and hydraulic lime, gypsum, and cement. The obtained mortars were characterized in their fresh state to assess their workability, and in a solid state after a proper cure to determine their characteristic Latent Heat Thermal Energy Storage (LHTES) properties and mechanical properties in both flexural and compressive modes, taking the mortars not containing any PCM as the reference. The results revealed that, with the proper selection of mortar formulations, it was possible to achieve suitable workability and adequate mechanical characteristics. The selection of a PEG with a low range of phase change temperatures, such as PEG 800, allows one to obtain mortars characterized by a melting/crystallization range that can be considered appropriate in applications characterized by cold climates. The production of a mixed PCM, composed of both PEGs, led to mortars displaying a large interval of melting/crystallization temperatures, which could be suitable in both warm and cold climates.

Physical Properties of an Eco-Sustainable, Form-Stable Phase Change Material Included in Aerial-Lime-Based Mortar Intended for Different Climates.

The aim of this experimental investigation was to produce a form-stable phase change material (PCM) able to reduce the need for nonrenewable energy resources required for the heating/cooling of buildings located in regions characterized by different climatic conditions. The innovative PCM must also be sustainable and must be produced according to the principles of the circular economy. To achieve such ambitious goals, a form-stable, sustainable PCM was produced through vacuum impregnation. The form-stable PCM was produced starting from a low-toxicity, low-flammability polyethylene glycol of medium molecular weight (PEG 800), which was included in porous stone granules obtained as waste products of the cutting/processing of local (Lecce) stone. The thermal properties and thermal stability of PEG 800 and of its PCM-composite were evaluated by employing differential scanning calorimetry (DSC) and thermo-gravimetric analysis (TGA). The appropriate parameters to perform the impregnation procedure were identified through rheological and calorimetric analyses. A simple leakage test was performed to assess if the PEG polymer can leak from the stone flakes. Finally, the new PCM was added as an aggregate in aerial-lime-based mortars, and the mortar's properties were analyzed in fresh (workability) and hardened (flexural and compressive strength and thermal characteristics) states for potential applications, particularly in ancient buildings.

Thermal Performance of Mortars Based on Different Binders and Containing a Novel Sustainable Phase Change Material (PCM).

Increasing concerns about climate change and global warming bring about technical steps for the development of several energy-efficient technologies. Since the building sector is one of the largest energy users for cooling and heating necessities, the incorporation of a proper energy-efficient material into the building envelopes could be an interesting solution for saving energy. Phase change material (PCM)-based thermal energy storage (TES) seems suitable to provide efficient energy redistribution. This is possible because the PCM is able to store and release its latent heat during the phase change processes that occurs according to the environmental temperature. The purpose of this paper was the characterization of the thermal properties of a composite PCM (i.e., Lecce stone/poly-ethylene glycol, previously developed) incorporated into mortar compositions based on different binders (i.e., hydraulic lime and cement). The study was carried out using an experimental set up through which it was possible to simulate the different seasons of the years. It was observed that the addition of PCM in mortars leads to a decrease of the maximum temperatures and increase of the minimum temperatures. Furthermore, the results shown a reduction of the heating and cooling needs, thus confirming the capability of this material to save energy.

Applications of Sustainable Polymer-Based Phase Change Materials in Mortars Composed by Different Binders.

Eco-sustainable, low toxic and low flammable poly-ethylene glycol (PEG) was forced into flakes of the porous Lecce stone (LS), collected as stone cutting wastes, employing a very simple cheap method, to produce a "form-stable" phase change material (PCM). The experimental PCM was included in mortars based on different binders (hydraulic lime, gypsum and cement) in two compositions. The main thermal and mechanical characteristics of the produced mortars were evaluated in order to assess the effects due to the incorporation of the PEG-based PCM. The mortars containing the PEG-based PCM were found to be suitable as thermal energy storage systems, still displaying the characteristics melting and crystallization peaks of PEG polymer, even if the related enthalpies measured on the mortars were appreciably reduced respect to pure PEG. The general reduction in mechanical properties (in flexural and compressive mode) measured on all the mortars, brought about by the presence of PEG-based PCM, was overcome by producing mortars possessing a greater amount of binder. The proposed LS/PEG composite can be considered, therefore, as a promising PCM system for the different mortars analyzed, provided that an optimal composition is identified for each binder.

Phase Change Materials for Energy Efficiency in Buildings and Their Use in Mortars.

The construction industry is responsible for consuming large amounts of energy. The development of new materials with the purpose of increasing the thermal efficiency of buildings is, therefore, becoming, imperative. Thus, during the last decades, integration of Phase Change Materials (PCMs) into buildings has gained interest. Such materials can reduce the temperature variations, leading to an improvement in human comfort and decreasing at the same time the energy consumption of buildings, due to their capability to absorb and release energy from/in the environment. In the present paper, recent experimental studies dealing with mortars or concrete-containing PCMs, used as passive building systems, have been examined. This review is mainly aimed at providing information on the currently investigated materials and the employed methodologies for their manufacture, as well as at summarizing the results achieved so far on this subject.