Monolithic Two-Terminal Perovskite/Perovskite/Silicon Triple-Junction Solar Cells with Open Circuit Voltage >2.8 V.

The efficiency of perovskite/silicon tandem solar cells has exceeded the previous record for III-V-based dual-junction solar cells. This shows the high potential of perovskite solar cells in multi-junction applications. Perovskite/perovskite/silicon triple-junction solar cells are now the next step to achieve efficient and low-cost multi-junction solar cells with an efficiency potential even higher than that for dual-junction solar cells. Here we present a perovskite/perovskite/silicon triple-junction solar cell with an open circuit voltage of >2.8 V, which is the record value reported for this structure so far. This is achieved through employing a gas quenching method for deposition of the top perovskite layer as well as optimization of interlayers between perovskite subcells. Moreover, for the measurement of our triple-junction solar cells, precise measurement procedures are implemented to ensure the reliability and accuracy of the reported values.

Complex refractive indices of Spiro-TTB and C60 for optical analysis of perovskite silicon tandem solar cells.

Evaporated charge extraction layers from organic molecular materials are vital in perovskite-based solar cells. For opto-electronic device optimization their complex refractive indices must be known for the visible and near infrared wavelength regime; however, accurate determination from thin organic films below 50 nm can be challenging. By combining spectrophotometry, variable angle spectroscopic ellipsometry, and X-ray reflectivity with an algorithm that simultaneously fits all available spectra, the complex refractive index of evaporated Spiro-TTB and C60 layers is determined with high accuracy. Based on that, an optical losses analysis for perovskite silicon solar cells shows that 15 nm of Spiro-TTB in the front of a n-i-p device reduces current by only 0.1 mA/cm2, compared to a substantial loss of 0.5 mA/cm2 due to 15 nm of C60 in a p-i-n device. Optical device simulation predicts high optical generation current densities of 19.7 and 20.1 mA/cm2 for the fully-textured, module-integrated p-i-n and n-i-p devices, respectively.

Vapor-Phase Formation of a Hole-Transporting Thiophene Polymer Layer for Evaporated Perovskite Solar Cells.

Homogeneous layer formation on textured silicon substrates is essential for the fabrication of highly efficient monolithic perovskite silicon tandem solar cells. From all well-known techniques for the fabrication of perovskite solar cells (PSCs), the evaporation method offers the highest degree of freedom for layer-by-layer deposition independent of the substrate's roughness or texturing. Hole-transporting polymers with high hole mobility and structural stability have been used as effective hole-transporting materials (HTMs) of PSCs. However, the strong intermolecular interactions of the polymers do not allow for a layer formation via the evaporation method, which is a big challenge for the perovskite community. Herein, we first applied a hole-transporting terthiophene polymer (PTTh) as an HTM for evaporated PSCs via an in situ vapor-phase polymerization using iodine (I2) as a sublimable oxidative agent. PTTh showed high hole mobility of 1.2 × 10-3 cm2/(V s) and appropriate energy levels as HTM in PSCs (EHOMO = -5.3 eV and ELUMO = -3.3 eV). The PSCs with the in situ vapor-phase polymerized PTTh hole-transporting layer and a co-evaporated perovskite layer exhibited a photovoltaic conversion efficiency of 5.9%, as a proof of concept, and high cell stability over time. Additionally, the polymer layer could fully cover the pyramidal structure of textured silicon substrates and was identified as an effective hole-transporting material for perovskite silicon tandem solar cells by optical simulation.

Semi-Transparent Perovskite Solar Cells with ITO Directly Sputtered on Spiro-OMeTAD for Tandem Applications.

Perovskite silicon tandem solar cells have the potential to overcome the efficiency limit of single-junction solar cells. For both monolithic and mechanically stacked tandem devices, a semi-transparent perovskite top solar cell, including a transparent contact, is required. Usually, this contact consists of a metal oxide buffer layer and a sputtered transparent conductive oxide. In this work, semi-transparent perovskite solar cells in the regular n-i-p structure are presented with tin-doped indium oxide (ITO) directly sputtered on the hole conducting material Spiro-OMeTAD. ITO process parameters such as sputter power, temperature, and pressure in the chamber are systematically varied. While a low temperature of 50 °C is crucial for good device performance, a low sputter power has only a slight effect, and an increased chamber pressure has no influence on device performance. For the 5 × 5 mm2 perovskite cell with a planar front side, a 105 nm thick ITO layer with a sheet resistance of 44 Ω sq-1 allowing for the omission of grid fingers and a MgF2 antireflection coating are used to improve transmission into the solar cells. The best device achieved an efficiency of 14.8%, which would result in 24.2% in a four-terminal tandem configuration.

Efficiency Enhancement and Hysteresis Mitigation by Manipulation of Grain Growth Conditions in Hybrid Evaporated-Spin-coated Perovskite Solar Cells.

Perovskite solar cells have become a game changer in the field of photovoltaics by reaching power conversion efficiencies beyond 23%. To achieve even higher efficiencies, it is necessary to increase the understanding of crystallization, grain formation, and layer ripening. In this study, by a systematic variation of methylammonium iodide (MAI) concentrations, we changed the stoichiometry and thereupon the crystal growth conditions in MAPbI3 perovskite solar cells, prepared by a two-step hybrid evaporation-spin-coating deposition method. Utilizing X-ray diffraction, scanning electron microscopy, atomic force microscopy, photoluminescence, and current-voltage ( J- V) characterization, we found that a relatively lower concentration of MAI, or in other words higher content of remnant and unconverted PbI2, correlates with smaller and stronger interconnected grains, as well as with an improved optoelectronic performance of the solar cells and mitigation of hysteresis. The possible explanations are grain and interface passivation by the excess PbI2 and a positive contribution of the grain boundaries to current extraction.

Novel Low-Temperature Process for Perovskite Solar Cells with a Mesoporous TiO2 Scaffold.

The most efficient organic-inorganic perovskite solar cells (PSCs) contain the conventional n-i-p mesoscopic device architecture using a semiconducting TiO2 scaffold combined with a compact TiO2 blocking layer for selective electron transport. These devices achieve high power conversion efficiencies (15-22%) but mainly require high-temperature sintering (>450 °C), which is not possible for temperature-sensitive substrates. Thus far, comparably little effort has been spent on alternative low-temperature (<150 °C) routes to realize high-efficiency TiO2-based PSCs; instead, other device architectures have been promoted for low-temperature processing. In this paper the compatibility of the conventional mesoscopic TiO2 device architecture with low-temperature processing is presented for the first time with the combination of electron beam evaporation for the compact TiO2 and UV treatment for the mesoporous TiO2 layer. Vacuum evaporation is introduced as an excellent deposition technique of uniform compact TiO2 layers, adapting smoothly to the rough fluorine-doped tin oxide substrate surface. Effective removal of organic binders by UV light is shown for the mesoporous scaffold. Entirely low-temperature-processed PSCs with TiO2 scaffold reach encouraging stabilized efficiencies of up to 18.2%. This process fulfills all requirements for monolithic tandem devices with high-efficiency silicon heterojunction solar cells as the bottom cell.

Controlled synthesis of multi-arm star polyether-polycarbonate polyols based on propylene oxide and CO2.

Multi-arm star copolymers based on a hyperbranched poly(propylene oxide) polyether-polyol (hbPPO) as a core and poly(propylene carbonate) (PPC) arms are synthesized in two steps from propylene oxide (PO), a small amount of glycidol and CO2 . The PPC arms are prepared via carbon dioxide (CO2 )/PO copolymerization, using hbPPO as a multifunctional macroinitiator and the (R,R)-(salcy)CoOBzF5 catalyst. Star copolymers with 14 and 28 PPC arms, respectively, and controlled molecular weights in the range of 2700-8800 g mol(-1) are prepared (Mw /Mn = 1.23-1.61). Thermal analysis reveals lowered glass transition temperatures in the range of -8 to 10 °C for the PPC star polymers compared with linear PPC, which is due to the influence of the flexible polyether core. Successful conversion of the terminal hydroxyl groups with phenylisocyanate demonstrates the potential of the polycarbonate polyols for polyurethane synthesis.