[Tissue biomechanics: connective tissue characterization : Cluster tissue biomechanics]. / Gewebebiomechanik: Charakterisierung von Bindegewebe : Cluster Gewebebiomechanik.

The various connective tissues of the body have different functions, which result from their specific structure and composition. The identification of this structure-function relationship is of great importance for various disciplines such as medicine, biology or tissue engineering. Connective tissue consists mainly of an extracellular matrix (ECM) and a limited number of cells. It is extremely adaptable because the activity of the cells remodels the composition and structure of the ECM in order to adapt the mechanical properties (functions) to the new demands (e.g. an increased mechanical stimulus).

The biomechanical properties of human menisci: A systematic review.

Biomechanical characterization of meniscal tissue ex vivo remains a critical need, particularly for the development of suitable meniscus replacements or therapeutic strategies that target the native mechanical properties of the meniscus. To date, a huge variety of test configurations and protocols have been reported, making it extremely difficult to compare the respective outcome parameters, thereby leading to misinterpretation. Therefore, the purpose of this systematic review was to identify test-specific parameters that contribute to uncertainties in the determination of mechanical properties of the human meniscus and its attachments, which derived from common quasi-static and dynamic tests in tension, compression, and shear. Strong evidence was found that the determined biomechanical properties vary significantly depending on the specific test parameters, as indicated by up to tenfold differences in both tensile and compressive properties. Test mode (stress relaxation, creep, cyclic) and configuration (unconfined, confined, in-situ), specimen shape and dimensions, preconditioning regimes, loading rates, post-processing of experimental data, and specimen age and degeneration were identified as the most critical parameters influencing the outcome measures. In conclusion, this work highlights an unmet need for standardization and reporting guidelines to facilitate comparability and may prove beneficial for evaluating the mechanical properties of novel meniscus constructs. STATEMENT OF SIGNIFICANCE: The biomechanical properties of the human meniscus have been studied extensively over the past decades. However, it remains unclear to what extent both test protocol and specimen-related differences are responsible for the enormous variability in material properties. Therefore, this systematic review analyzes the biomechanical properties of the human meniscus in the context of the underlying testing protocol. The most sensitive parameters affecting the determination of mechanical properties were identified and critically discussed. Currently, it is of utmost importance for scientists evaluating potential meniscal scaffolds and biomaterials to have a control group rather than a direct comparison to the literature. Standardization of both test procedures and reporting requirements is needed to improve and accelerate the development of meniscal replacement constructs.

Radial and longitudinal meniscus tears show different gapping patterns under stance phase conditions.

Meniscal tearing can increase the contact pressure between the tibia and femur by causing gapping of torn meniscus tissue. The aim of this study was to quantify gapping behavior of radial and longitudinal tears and their impact on peak contact pressure and mean contact area. Twelve porcine knee joints underwent unicondylar, convertible osteotomy for exact tear application and consecutive suturing. Six tantalum marker beads were positioned along meniscus tears. The joints were preloaded with sinusoidal loading cycles ranging between 0 N and 350 N. Peak load was held constant and two synchronized Roentgen stereophotogrammetric analysis x-ray images were obtained to evaluate gapping, peak contact pressure and mean contact area in the native, torn and repaired states. There was no change in gapping or peak contact pressure in longitudinal tear. By contrast, the radial tear led to a significant gapping when compared to the native state, while the inside-out suture was able to restore gapping in parts of the meniscus. An increase in contact pressure after radial tear was detected, which was again normalized after suturing. The most important finding of the study is that longitudinal tears did not gap under pure axial loading, whereas radial tears tended to separate the tear interfaces.

Impact of hyaluronic acid injection on the knee joint friction.

PURPOSE: The purpose of this in vitro study was to investigate whether or not hyaluronic acid supplementation improves knee joint friction during osteoarthritis progression under gait-like loading conditions. METHODS: Twelve human cadaveric knee joints were equally divided into mild and moderate osteoarthritic groups. After initial conservative preparation, a passive pendulum setup was used to test the whole joints under gait-like conditions before and after hyaluronic acid supplementation. The friction-related damping properties given by the coefficient of friction µ and the damping coefficient c (in kg m2/s) were calculated from the decaying flexion-extension motion of the knee. Subsequently, tibial and femoral cartilage and meniscus samples were extracted from the joints and tested in an established dynamic pin-on-plate tribometer using synthetic synovial fluid followed by synthetic synovial fluid supplemented with hyaluronic acid as lubricant. Friction was quantified by calculating the coefficient of friction. RESULTS: In the pendulum tests, the moderate OA group indicated significantly lower c0 values (p < 0.05) under stance phase conditions and significantly lower µ0 (p = 0.01) values under swing phase conditions. No degeneration-related statistical differences were found for µend or cend. Friction was not significantly different (p > 0.05) with regard to mild and moderate osteoarthritis in the pin-on-plate tests. Additionally, hyaluronic acid did not affect friction in both, the pendulum (p > 0.05) and pin-on-plate friction tests (p > 0.05). CONCLUSION: The results of this in vitro study suggested that the friction of cadaveric knee joint tissues does not increase with progressing degeneration. Moreover, hyaluronic acid viscosupplementation does not lead to an initial decrease in knee joint friction.

Free-floating medial meniscus implant kinematics do not change after simulation of medial open-wedge high tibial osteotomy and notchplasty.

PURPOSE: The purpose of this in-vitro study was to examine the kinematics of an artificial, free-floating medial meniscus replacement device under dynamic loading situations and different knee joint states. METHODS: A dynamic knee simulator was used to perform dynamic loading exercises on three neutrally aligned and three 10° valgus aligned (simulating a medial openwedge high tibial osteotomy - MOWHTO) left human cadaveric knee joints. The knee joints were tested in three states (intact, conventional notchplasty, extended notchplasty) while 11 randomised exercises were simulated (jump landing, squatting, tibial rotation and axial ground impacts at 10°, 30° and 60° knee joint flexion) to investigate the knee joint and implant kinematics by means of rigidly attached reflective marker sets and an according motion analysis. RESULTS: The maximum implant translation relative to the tibial plateau was < 13 mm and the maximum implant rotation was < 19° for all exercises. Both, the notchplasties and the valgus knee alignment did not affect the device kinematics. CONCLUSIONS: The results of the present in-vitro study showed that the non-anchored free-floating device remains within the medial knee joint gap under challenging dynamic loading situations without indicating any luxation tendencies. This also provides initial benchtop evidence that the device offers suitable stability and kinematic behaviour to be considered a potential alternative to meniscus allograft transplantation in combination with an MOWHTO, potentially expanding the patient collective in the future.

A Bioinspired Orthopedic Biomaterial with Tunable Mechanical Properties Based on Sintered Titanium Fibers.

Inadequate mechanical compliance of orthopedic implants can result in excessive strain of the bone interface, and ultimately, aseptic loosening. It is hypothesized that a fiber-based biometal with adjustable anisotropic mechanical properties can reduce interface strain, facilitate continuous remodeling, and improve implant survival under complex loads. The biometal is based on strategically layered sintered titanium fibers. Six different topologies are manufactured. Specimens are tested under compression in three orthogonal axes under 3-point bending and torsion until failure. Biocompatibility testing involves murine osteoblasts. Osseointegration is investigated by micro-computed tomography and histomorphometry after implantation in a metaphyseal trepanation model in sheep. The material demonstrates compressive yield strengths of up to 50 MPa and anisotropy correlating closely with fiber layout. Samples with 75% porosity are both stronger and stiffer than those with 85% porosity. The highest bending modulus is found in samples with parallel fiber orientation, while the highest shear modulus is found in cross-ply layouts. Cell metabolism and morphology indicate uncompromised biocompatibility. Implants demonstrate robust circumferential osseointegration in vivo after 8 weeks. The biometal introduced in this study demonstrates anisotropic mechanical properties similar to bone, and excellent osteoconductivity and feasibility as an orthopedic implant material.

Accuracy measurement of different marker based motion analysis systems for biomechanical applications: A round robin study.

INTRODUCTION: Multiple camera systems are widely used for 3D-motion analysis. Due to increasing accuracies these camera systems gained interest in biomechanical research areas, where high precision measurements are desirable. In the current study different measurement systems were compared regarding their measurement accuracy. MATERIALS AND METHODS: Translational and rotational accuracy measurements as well as the zero offset measurements of seven different measurement systems were performed using two reference devices and two different evaluation algorithms. All measurements were performed in the same room with constant temperature at the same laboratory. Equal positions were measured with the systems according to a standardized protocol. Measurement errors were determined and compared. RESULTS: The highest measurement errors were seen for a measurement system using active ultrasonic markers, followed by another active marker measurement system (infrared) having measurement errors up to several hundred micrometers. The highest accuracies were achieved by three stereo camera systems, using passive 2D marker points having errors typically below 20 µm. CONCLUSIONS: This study can help to better assess the results obtained with different measurement systems. With the focus on the measurement accuracy, only one aspect in the selection of a system was considered. Depending on the requirements of the user, other factors like measurement frequency, the maximum analyzable volume, the marker type or the costs are important factors as well.

Comparison of Knotless and Knotted Single-Anchor Repair for Ruptures of the Upper Subscapularis Tendon: Outcomes at 2-Year Follow-up.

Background: Both knotted and knotless single-anchor repair techniques are used to repair transmural ruptures of the upper subscapularis (SSC) tendon. However, it is still unclear which technique provides better clinical and radiological results. Purpose/Hypothesis: To compare the clinical and magnetic resonance imaging (MRI) outcomes of knotless and knotted single-anchor repair techniques in patients with a transmural rupture of the upper SSC tendon at 2-year follow-up. It was hypothesized that the 2 techniques would not differ significantly in outcomes. Study Design: Cohort study; Level of evidence, 3. Methods: Forty patients with a transmural tear of the upper SSC tendon (grade 2 or 3 according to Fox and Romeo) were retrospectively enrolled. Depending on the repair technique, patients were assigned to either the knotless single-anchor or knotted single-anchor group. After a mean follow-up of 2.33 ± 0.43 years, patients were assessed by the ASES, WORC, OSS, CS, and SSV. A clinical examination that included the bear-hug, the lift-off, and the belly-press tests was performed, in which the force exerted by the subjects was measured. In addition, all patients underwent MRI of the affected shoulder to assess repair integrity, tendon width, fatty infiltration, signal-to-signal ratio of the upper and lower SSC muscle, and atrophy of the SSC muscle. Results: No significant difference was found between the 2 groups on any of the clinical scores [ASES (P = .272), WORC (P = .523), OSS (P = .401), CS (P = .328), SSV (P = .540)] or on the range-of-motion or force measurements. Apart from a higher signal-to-signal ratio of the lower SSC muscle in the knotless group (P = .017), no significant difference on imaging outcomes was found between the 2 groups. Conclusion: Both techniques can be used in surgical practice, as neither was found to be superior to the other in terms of clinical or imaging outcomes at 2-year follow-up.

Are Knotted or Knotless Techniques Better for Reconstruction of Full-Thickness Tears of the Superior Portion of the Subscapularis Tendon? A Study in Cadavers.

BACKGROUND: Knotted and knotless single-anchor reconstruction techniques are frequently performed to reconstruct full-thickness tears of the upper portion of subscapularis tendon. However, it is unclear whether one technique is superior to the other. QUESTIONS/PURPOSES: (1) When comparing knotless and knotted single-anchor reconstruction techniques in full-thickness tears of the upper subscapularis tendon, is there a difference in stiffness under cyclic load? (2) Are there differences in cyclic gapping between knotless and knotted reconstructions? (3) Are there differences in the maximal stiffness, yield load, and ultimate load to failure? (4) What are the modes of failure of knotless and knotted reconstruction techniques? METHODS: Eight matched pairs of human cadaveric shoulders were dissected, and a full-thickness tear of the subscapularis tendon (Grade 3 according to the Fox and Romeo classification) was created. The cadavers all were male specimens, with a median (range) age of 69 years (61 to 75). Before biomechanical evaluation, the specimens were randomized into two equal reconstruction groups: knotless single anchor and knotted single anchor. All surgical procedures were performed by a single orthopaedic surgeon who subspecializes in sports orthopedics and shoulder surgery. With a customized set up that was integrated in a dynamic material testing machine, the humeri were consecutively loaded from 10 N to 60 N, from 10 N to 100 N, and from 10 N to 180 N for 50 cycles. Furthermore, the gapping behavior of the tear was analyzed using a video tracking system. Finally, the stiffness, gapping, maximal stiffness, yield loads, and maximum failure loads of both reconstruction groups were statistically analyzed. Failure was defined as retearing of the reconstructed gap threshold due to rupture of the tendon and/or failure of the knots or anchors. After biomechanical testing, bone quality was measured at the footprint of the subscapularis using microCT in all specimens. Bone quality was equal between both groups. To detect a minimum 0.15-mm difference in gap formation between the two repair techniques (with a 5% level of significance; α = 0.05), eight matched pairs (n = 16 in total) were calculated as necessary to achieve a power of at least 90%. RESULTS: The first study question can be answered as follows: for stiffness under cyclic load, there were no differences with the numbers available between the knotted and knotless groups at load stages of 10 N to 60 N (32.7 ± 3.5 N/mm versus 34.2 ± 5.6 N/mm, mean difference 1.5 N/mm [95% CI -6.43 to 3.33]; p = 0.55), 10 N to 100 N (45.0 ± 4.8 N/mm versus 45.2 ± 6.0 N/mm, mean difference 0.2 N/mm [95% CI -5.74 to 6.04]; p = 0.95), and 10 N to 180 N (58.2 ± 10.6 N/mm versus 55.2 ± 4.7 N/mm, mean difference 3 N/mm [95% CI -5.84 to 11.79]; p = 0.48). In relation to the second research question, the following results emerged: For cyclic gapping, there were no differences between the knotted and knotless groups at any load levels. The present study was able to show the following with regard to the third research question: Between knotted and knotless repairs, there were no differences in maximal load stiffness (45.3 ± 8.6 N/mm versus 43.5 ± 10.2 N/mm, mean difference 1.8 [95% CI -11.78 to 8.23]; p = 0.71), yield load (425.1 ± 251.4 N versus 379.0 ± 169.4 N, mean difference 46.1 [95% CI -276.02 to 183.72]; p = 0.67), and failure load (521.1 ± 266.2 N versus 475.8 ± 183.3 N, mean difference 45.3 [95% CI -290.42 to 199.79]; p = 0.69). Regarding the fourth question concerning the failure modes, in the knotted repairs, the anchor tore from the bone in 2 of 8, the suture tore from the tendon in 6 of 8, and no suture slipped from the eyelet; in the knotless repairs, the anchor tore from the bone in 2 of 8, the suture tore from the tendon in 3 of 8, and the threads slipped from the eyelet in 3 of 8. CONCLUSION: With the numbers available, we found no differences between single-anchor knotless and knotted reconstruction techniques used to repair full-thickness tears of the upper portion of subscapularis tendon. CLINICAL RELEVANCE: The reconstruction techniques we analyzed showed no differences in terms of their primary stability and biomechanical properties at the time of initial repair and with the numbers available. In view of these experimental results, it would be useful to conduct a clinical study in the future to verify the translationality of the experimental data of the present study.

Meniscus Injury and its Surgical Treatment Does not Increase Initial Whole Knee Joint Friction.

While it is generally accepted that traumatic meniscus pathologies lead to degenerative articular cartilage changes in the mid-to long-term and consecutively to post-traumatic osteoarthritis (PTOA), very little is known about how such injuries initiate tribological changes within the knee and their possible impact on PTOA acceleration. Therefore, the aim of this study was to investigate the influence of three different medial meniscus states (intact, posterior root tear, total meniscectomy) on the initial whole knee joint friction. Six ovine knee joints were tested in a passive pendulum friction testing device under an axial load of 250 N and an initial deflection of 12°, representing swing phase conditions, and under an axial load of 1000 N and an initial deflection of 5°, simulating stance phase conditions. To additionally consider the influence of the time-dependent viscoelastic nature of the knee joint soft tissues on whole joint friction, the tests were performed twice, directly following load application and after 20 min creep loading of either 250 N or 1000 N axial load. On the basis of a three-dimensional joint kinematic analysis, the energy loss during the passive joint motion was analyzed, which allowed considerations on frictional and damping processes within the joint. The so-called "whole knee joint" friction was evaluated using the boundary friction model from Stanton and a viscous friction model from Crisco et al., both analyzing the passive joint flexion-extension motion in the sagittal plane. Significantly lower friction coefficients were observed in the simulated swing phase after meniscectomy (p < 0.05) compared to the intact state. No initial whole joint friction differences between the three meniscus states (p > 0.05) were found under stance phase conditions. Soft tissue creeping significantly increased all the determined friction coefficients (p < 0.05) after resting under load for 20 min. The exponential decay function of the viscous friction model provided a better fit (R 2∼0.99) to the decaying flexion-extension data than the linear decay function of the boundary friction model (R 2∼0.60). In conclusion, this tribological in vitro study on ovine knee joints indicated that neither a simulated posterior medial meniscus root tear nor the removal of the medial meniscus resulted in an initially increased whole joint friction.

Neuromapping of the Capsuloligamentous Knee Joint Structures.

PURPOSE: To investigate neuromuscular electromyographic response of the of the upper and lower leg muscles after the application of an intraoperative, isolated mechanical stimulus of the capsuloligamentous structures, including the anterior (ACL) and posterior cruciate ligaments (PCL), lateral (LM) and medial menisci (MM), plica mediopatellaris (PM), and Hoffa's fat pat (HFP). METHODS: The electromyographic response of the upper and lower leg muscles (M. rectus femoris; M. vastus medialis; M. semitendinosus; M. biceps femoris; M. gastrocnemius lateralis) of 15 male patients were measured after an isolated mechanical stimulus of the capsuloligamentous structures during an arthroscopic intervention using a customized intraoperative setup. Target parameters were the short (SLR; <30 milliseconds) and medium latency responses (MLR; >30 milliseconds) after the mechanically-induced trigger. RESULTS: The ACL, PCL, LM, and MM displayed high interindividual reproducibility of >76%. The MM was the only structure indicating both an SLR and MLR for all muscles. Although signals could be detected, there was no reproducibility in electromyographic signal activation for the HFP. The most rapid MLR was observed for the PM (quadriceps: 37 milliseconds). CONCLUSIONS: Each stimulated structure displayed an individual MLR response, which allowed us to create neuromapping combining the anatomical and quantitative representations of the individual muscular activation patterns after isolated mechanical stimulation of the capsuloligamentous knee joint structures, corroborating our hypothesis. LEVEL OF EVIDENCE: Diagnostic - Level II.

Forces at the Anterior Meniscus Attachments Strongly Increase Under Dynamic Knee Joint Loading.

BACKGROUND: The anatomic appearance and biomechanical and clinical importance of the anterior meniscus roots are well described. However, little is known about the loads that act on these attachment structures under physiological joint loads and movements. HYPOTHESES: As compared with uniaxial loading conditions under static knee flexion angles or at very low flexion-extension speeds, more realistic continuous movement simulations in combination with physiological muscle force simulations lead to significantly higher anterior meniscus attachment forces. This increase is even more pronounced in combination with a longitudinal meniscal tear or after total medial meniscectomy. STUDY DESIGN: Controlled laboratory study. METHODS: A validated Oxford Rig-like knee simulator was used to perform a slow squat, a fast squat, and jump landing maneuvers on 9 cadaveric human knee joints, with and without muscle force simulation. The strains in the anterior medial and lateral meniscal periphery and the respective attachments were determined in 3 states: intact meniscus, medial longitudinal tear, and total medial meniscectomy. To determine the attachment forces, a subsequent in situ tensile test was performed. RESULTS: Muscle force simulation resulted in a significant strain increase at the anterior meniscus attachments of up to 308% (P < .038) and the anterior meniscal periphery of up to 276%. This corresponded to significantly increased forces (P < .038) acting in the anteromedial attachment with a maximum force of 140 N, as determined during the jump landing simulation. Meniscus attachment strains and forces were significantly influenced (P = .008) by the longitudinal tear and meniscectomy during the drop jump simulation. CONCLUSION: Medial and lateral anterior meniscus attachment strains and forces were significantly increased with physiological muscle force simulation, corroborating our hypothesis. Therefore, in vitro tests applying uniaxial loads combined with static knee flexion angles or very low flexion-extension speeds appear to underestimate meniscus attachment forces. CLINICAL RELEVANCE: The data of the present study might help to optimize the anchoring of meniscal allografts and artificial meniscal substitutes to the tibial plateau. Furthermore, this is the first in vitro study to indicate reasonable minimum stability requirements regarding the reattachment of torn anterior meniscus roots.

Degeneration Affects Three-Dimensional Strains in Human Menisci: In situ MRI Acquisition Combined With Image Registration.

Degenerative changes of menisci contribute to the evolution of osteoarthritis in the knee joint, because they alter the load transmission to the adjacent articular cartilage. Identifying alterations in the strain response of meniscal tissue under compression that are associated with progressive degeneration may uncover links between biomechanical function and meniscal degeneration. Therefore, the goal of this study was to investigate how degeneration effects the three-dimensional (3D; axial, circumferential, radial) strain in different anatomical regions of human menisci (anterior and posterior root attachment; anterior and posterior horn; pars intermedia) under simulated compression. Magnetic resonance imaging (MRI) was performed to acquire image sequences of 12 mild and 12 severe degenerated knee joints under unloaded and loaded [25%, 50% and 100% body weight (BW)] conditions using a customized loading device. Medial and lateral menisci as well as their root attachments were manually segmented. Intensity-based rigid and non-rigid image registration were performed to obtain 3D deformation fields under the respective load levels. Finally, the 3D voxels were transformed into hexahedral finite-element models and direction-dependent local strain distributions were determined. The axial compressive strain in menisci and meniscal root attachments significantly increased on average from 3.1% in mild degenerated joints to 7.3% in severe degenerated knees at 100% BW (p ≤ 0.021). In severe degenerated knee joints, the menisci displayed a mean circumferential strain of 0.45% (mild: 0.35%) and a mean radial strain of 0.41% (mild: 0.37%) at a load level of 100% BW. No significant changes were observed in the circumferential or radial directions between mild and severe degenerated knee joints for all load levels (p > 0.05). In conclusion, high-resolution MRI was successfully combined with image registration to investigate spatial strain distributions of the meniscus and its attachments in response to compression. The results of the current study highlight that the compressive integrity of the meniscus decreases with progressing tissue degeneration, whereas the tensile properties are maintained.

Automatic segmentation of knee menisci - A systematic review.

Magnetic resonance imaging (MRI) has proved to be an invaluable component of pathogenesis research in osteoarthritis. Nevertheless, the detection of a meniscal lesion from magnetic resonance (MR) images is always challenging for both clinicians and researchers, because the surrounding tissues lead to similar signals within MR measurements, thus being difficult to discriminate. Moreover, the size and shape of osteoarthritic and non-osteoarthritic menisci vary to a large extent between individuals of same features, e.g. height, weight, age, etc. An effective way to visualize the entire volume of knee menisci is to segment the menisci voxels from the MR images, which is also useful to evaluate particular properties quantitatively. However, segmentation is a tedious and time-consuming task, and requires adequate training for being done properly. With the advancement of both MRI technology and computer methods, researchers have developed several algorithms to automate the task of meniscus segmentation of the individual knee during the last two decades. The objective of this systematic review was to present available fully automatic and semi-automatic segmentation methods of the knee meniscus published in different scientific articles according to the PRISMA statement. This review should provide a vivid description of the scientific advancements to clinicians and researchers in this field to help developing novel automated methods for clinical applications.

Impact of five different medial patellofemoral ligament-reconstruction strategies and three different graft pre-tensioning states on the mean patellofemoral contact pressure: a biomechanical study on human cadaver knees.

BACKGROUND: The medial patellofemoral ligament (MPFL) is the main stabiliser of the patella and thus mostly reconstructed in the surgical treatment of patellofemoral dislocation. The aims of this study were to gain a better understanding of the influence of altered MPFL graft-fixation locations and different graft pre-tensions on patellofemoral contact pressure. METHODS: Six human cadaveric knee joints were placed in a six-degree-of-freedom knee simulator. Mean PFCP (mPFCP) was evaluated in knee flexion of 0, 30 and 90° using a calibrated pressure-measurement system. After data assessment of the native knee joint, five MPFL reconstruction conditions were conducted: Anatomical double bundle; non-anatomical proximal patellar; non-anatomical distal patellar; non-anatomical proximal femoral; non-anatomical ventral femoral. The gracilis graft was fixed at a defined knee flexion of 30° and pre-tensioned to 2, 10 and 20 N. RESULTS: Kruskal-Wallis testing resulted in no mPFCP differences between the native and anatomical reconstruction states. Comparing the native and anatomical reconstruction states with the non-anatomical reconstruction states, no difference in the mPFCP both in knee extension (0°) (p>0.366) and in 30° knee flexion (p>0.349) was found. At 90° knee flexion, the following differences were identified: compared to the native knee state, the mPFCP increased after non-anatomical proximal femoral and non-anatomical ventral femoral reconstruction by 257% (p=0.04) and 292% (p=0.016), respectively. Compared to the anatomical reconstruction state, the mPFCP increased after non-anatomical proximal femoral reconstruction by 199% (p=0.042). DISCUSSION AND CONCLUSIONS: With respect to all study findings and to restore a physiological PFCP, we recommend using the anatomical footprints for MPFL reconstruction and a moderate graft pretensioning of 2-10 N.

ACL double-bundle reconstruction with one tibial tunnel provides equal stability compared to two tibial tunnels.

PURPOSE: The purpose of this study was to investigate whether an anterior cruciate ligament (ACL) double-bundle reconstruction with one tibial tunnel displays the same in vitro stability as a conventional double-bundle reconstruction with two tibial tunnels when using the same tensioning protocol. METHODS: In 11 fresh-frozen cadaveric knees, ACL double-bundle reconstruction with one and two tibial tunnels was performed. The two grafts were tightened using 80 N in different flexion angles (anteromedial-bundle at 60° and posterolateral-bundle at 15°). Anterior tibial translation (134 N) and translation with combined rotatory and valgus loads (10 Nm valgus stress and 4 Nm internal tibial torque) were determined at 0°, 30°, 60° and 90° flexion. Measurements were taken in intact ACL, resected ACL, three-tunnel reconstruction and four-tunnel reconstruction. Additionally, the tension on the grafts was determined. Student's t test was performed for statistical analysis of the related samples. Significance was set at p < 0.017 according to Bonferroni correction. RESULTS: The two reconstructive techniques displayed no significant differences in comparison with the intact ACL in anterior tibial translation at 0°, 60° and 90° of flexion. The same results were obtained for the anterior tibial translation with a combined rotatory load at 60° and 90°. When directly comparing both reconstructive techniques, there were no significant differences for the anterior tibial translation and combined rotatory load at all flexion angles. The measured tension on grafts displayed similar load sharing between both bundles. Except at full extension, both grafts displayed a significantly different tension increase under anterior tibial translation for both techniques (p = 0.0086). CONCLUSIONS: Tightening both bundles in ACL double-bundle reconstruction with one or two tibial tunnels in different flexion angles achieved comparable restoration of stability, although there was different load sharing on the bundles. With regard to individualized ACL reconstruction, the double-bundle technique with one tibial tunnel offers a possibility to address small tibial insertion sites without compromising the advantages of a double-bundle procedure.

Impact of measurement errors on the determination of the linear modulus of human meniscal attachments.

For the development of meniscal substitutes and related finite element models it is necessary to know the mechanical properties of the meniscus and its attachments. Measurement errors can falsify the determination of material properties. Therefore the impact of metrological and geometrical measurement errors on the determination of the linear modulus of human meniscal attachments was investigated. After total differentiation the error of the force (+0.10%), attachment deformation (-0.16%), and fibre length (+0.11%) measurements almost annulled each other. The error of the cross-sectional area determination ranged from 0.00%, gathered from histological slides, up to 14.22%, obtained from digital calliper measurements. Hence, total measurement error ranged from +0.05% to -14.17%, predominantly affected by the cross-sectional area determination error. Further investigations revealed that the entire cross-section was significantly larger compared to the load-carrying collagen fibre area. This overestimation of the cross-section area led to an underestimation of the linear modulus of up to -36.7%. Additionally, the cross-sections of the collagen-fibre area of the attachments significantly varied up to +90% along their longitudinal axis. The resultant ratio between the collagen fibre area and the histologically determined cross-sectional area ranged between 0.61 for the posterolateral and 0.69 for the posteromedial ligament. The linear modulus of human meniscal attachments can be significantly underestimated due to the use of different methods and locations of cross-sectional area determination. Hence, it is suggested to assess the load carrying collagen fibre area histologically, or, alternatively, to use the correction factors proposed in this study.

Effect of partial meniscectomy at the medial posterior horn on tibiofemoral contact mechanics and meniscal hoop strains in human knees.

We examined the influence of partial meniscectomy of 10 mm width on 10 human cadaveric knee joints, as it is performed during the treatment of radial tears in the posterior horn of the medial meniscus, on maximum contact pressure, contact area (CA), and meniscal hoop strain in the lateral and medial knee compartments. In case of 0° and 30° flexion angle, 20% and 50% partial meniscectomy did not influence maximum contact pressure and area. Only in case of 60° knee flexion, 50% partial resection increased medial maximum contact pressure and decreased the medial CA statistically significant. However, 100% partial resection increased maximum contact pressure and decreased CA significantly in the meniscectomized medial knee compartment in all tested knee positions. No significant differences were noted for meniscal hoop strain. From a biomechanical point of view, our in vitro study suggests that the medial joint compartment is not in danger of accelerated cartilage degeneration up to a resection limit of 20% meniscal depth and 10 mm width. Contact mechanics are likely to be more sensitive to partial meniscectomy at higher flexion angles, which has to be further investigated.