Dye removal by activated carbon produced from Agave americana fibers: stochastic isotherm and fractal kinetic studies.

The present work investigates the use of Agave americana fibers (AGF) as a precursor for activated carbon (AC) preparation via chemical activation using phosphoric acid (H3PO4), and the study of the influence of the preparation conditions on the adsorption capacity of the prepared AC toward Alpacide Yellow (AY). The preparation experiments have been conducted at different impregnation ratios: acid/AGF (20 g/1 g, 30 g/1 g, and 40 g/1 g) with varied impregnation times (2 h, 4 h, and 6 h) and at different carbonization temperatures (200 °C, 400 °C, and 600 °C). The impregnation ratio of 40 g/1 g, the impregnation time of 6 h, and the carbonization temperature of 400 °C were selected as the optimal conditions for the preparation of AC with enhanced properties. Despite its low specific surface area (25 m2/g), the prepared AC showed a higher adsorption capacity toward AY (5.71 mg/g) as compared with that of the commercial activated carbon (CC) (5.27 mg/g) which showed a higher specific surface area (825 m2/g). This could be due to the existence of pores and functional groups on the surface of AC, as evidenced by the analysis results of FTIR, DSC, and SEM. The adsorption process was found fast and fractal since it followed the kinetic model of the Brouers-Sotolongo fractal (BSf) (R2 = 0.999), while the mathematical modeling of the adsorption isotherm of AY on the synthesized AC was stochastic since it followed the General Brouers-Sotolongo (GBS) (R2 = 0.999).

Effect of the adsorption pH and temperature on the parameters of the Brouers-Sotolongo models.

The goal of the present paper was to elucidate if-and how-the parameters of the Brouers-Sotolongo fractal (BSf) (n,α) kinetic model (α and τC) on the one hand, and of the generalised Brouers-Sotolongo (GBS) isotherm model (a and b) on the other hand, are correlated with adsorption pH and temperature. For that purpose, adsorption of aqueous solutions of two common dyes, methylene blue (MB) and methyl orange (MO) was carried out on four activated carbons (ACs) at three temperatures (25, 35 and 50 °C) and three pH (2.5, 5 and 8). Adsorption kinetics and isotherms were measured, and the corresponding curves were best fitted with specific forms of the aforementioned models, and corresponding to equations known as BSf (1,α) kinetic and Brouers-Gaspard isotherm models. Correlations between all model parameters and adsorption conditions were found, bringing some information about the adsorbate-adsorbent interaction.

Influence of alternating current on the adsorption of indigo carmine.

The main purpose of this work is to study the effect of a new process of accelerating which consist to couple the electrochemical process with the adsorption to remove an anionic dye, the indigo carmine. That is why, we investigated the effects of the new process of accelerating the adsorption process by using alternating current (AC) on the retention of an anionic dye, the indigo carmine. The adsorption capacity of dye (mg/g) was raised with the raise of current voltage in solution, temperature, and initial indigo carmine concentration and decreased with the increase of initial solution pH, current density, and mass of carbon. The results demonstrate that the removal efficiency of 97.0 % with the current voltage of 15 V is achieved at a current density of 0.014 A/cm2, of pH 2 using zinc as electrodes and contact time of 210 min for adsorption in the presence of AC. Concerning the adsorption without AC, the results obtained showed that for an initial concentration equal to 20 mg/L, more than 95 % amount of adsorbed dye was retained after 405 min of contact in batch system. The comparison between adsorption in the presence and absence of an alternating current shows the importance of the alternating current in the acceleration of the adsorption method and improve the performances of FILTRASORB 200. For both cases, the adsorption mechanism follows the fractal kinetics BSf(n,α) model and the Brouers-Sotolongo isotherm model provides a good fit of the experimental data for both adsorption with and without alternating current.