Spatial beam self-cleaning and supercontinuum generation with Yb-doped multimode graded-index fiber taper based on accelerating self-imaging and dissipative landscape.

We experimentally demonstrate spatial beam self-cleaning and supercontinuum generation in a tapered Ytterbium-doped multimode optical fiber with parabolic core refractive index profile when 1064 nm pulsed beams propagate from wider (122 µm) into smaller (37 µm) diameter. In the passive mode, increasing the input beam peak power above 20 kW leads to a bell-shaped output beam profile. In the active configuration, gain from the pump laser diode permits to combine beam self-cleaning with supercontinuum generation between 520-2600 nm. By taper cut-back, we observed that the dissipative landscape, i.e., a non-monotonic variation of the average beam power along the MMF, leads to modal transitions of self-cleaned beams along the taper length.

Distributed Bragg reflector fiber laser directly written in a composite fiber manufactured by melting phosphate glass in a silica tube.

We demonstrate a single-frequency distributed Bragg reflector (DBR) fiber laser based on the novel erbium-doped composite fiber fabricated by melting phosphate glass in a silica tube. The fabricated composite fiber was single-mode at the wavelength of 1.55 µm; the measured cutoff wavelength was 1.4 µm. The composite fiber was photosensitive to irradiation at the wavelength of 193 nm. Using the phase mask method, the DBR fiber laser cavity with the total length of 21 mm was inscribed directly into the erbium-doped composite fiber. A stable single-frequency regime of the fabricated DBR laser at the wavelength of 1565 nm is demonstrated.

Four-photon absorption cross-section measurements in UV fused silica at 473 nm.

With the use of I- and z-scan techniques, the four-photon absorption cross section in a UV fused silica sample has been measured to be σ4=(1.0±0.5)×10-115 cm8 s3 at 473 nm. This value is more than an order of magnitude lower than that known for other optical materials (KBr, KI, NaCl, TeO2, and GeS2).

Raman fiber laser with random distributed feedback based on a twin-core fiber.

An operation of a linearly polarized Raman fiber laser with random distributed feedback based on a polarization-maintaining twin-core fiber (TCF) is demonstrated for the first time, to the best of our knowledge. The results indicate that the TCF allows one to obtain laser generation with a linewidth that is about five times smaller than that for the random laser based on a conventional fiber with similar parameters. The reasons for narrowing include both the weakening of nonlinear effects due to the power density reduction and the spectrally selective properties of the TCF.

High-beam quality, high-efficiency laser based on fiber with heavily Yb(3+)-doped phosphate core and silica cladding.

We have fabricated and tested a composite fiber with an Yb(3+)-doped phosphate glass core and silica cladding. Oscillation with a slope efficiency of 74% was achieved using core pumping at 976 nm with fiber lengths of 48-90 mm in a simple laser configuration, where the cavity was formed by a high-reflectivity Bragg grating and the cleaved fiber end. The measured M(2) factors were as low as 1.05-1.22 even though the fiber was multimode at the lasing wavelength.

Multicore fiber with rectangular cross-section.

We have fabricated, to our knowledge, the first rectangular cross-section multicore fiber with eight cores arranged in a line. We have shown that the rectangular cross-section remains practically unchanged during the fiber-drawing process. The heterogeneous version of the proposed fiber design could be beneficial for crosstalk reduction because of the low influence of fiber bends on crosstalk between neighboring cores.

Phosphate-core silica-clad Er/Yb-doped optical fiber and cladding pumped laser.

We present a composite optical fiber with a Er/Yb co-doped phosphate-glass core in a silica glass cladding as well as cladding pumped laser. The fabrication process, optical properties, and lasing parameters are described. The slope efficiency under 980 nm cladding pumping reached 39% with respect to the absorbed pump power and 28% with respect to the coupled pump power. Due to high doping level of the phosphate core optimal length was several times shorter than that of silica core fibers.

Single-mode all-silica photonic bandgap fiber with 20-microm mode-field diameter.

An all-silica photonic bandgap fiber with a cladding index difference of approximately 2 % and diameter-to-pitch ratio (d/wedge) of 0.12 was fabricated and studied. To our knowledge, this is the first report on the properties of photonic bandgap fiber with such a small d/wedge. The fiber is single-mode in the fundamental bandgap. The mode field diameter in the 1000-1200 nm wavelength range is 19-20 microm. The minimum loss in the same range is 20 dB/km for a 30-cm bending diameter. In our opinion, all-silica photonic bandgap fiber can serve as a potential candidate for achieving single-mode propagation with a large mode area.

Effect of polymer coating on leakage losses in Bragg fibers.

It is found that the reflection of leaky radiation from the interface between the outer silica cladding and the coating polymer greatly modifies the loss spectrum of Bragg fibers. A simple model that describes this effect is proposed and confirmed by measurement and computation.

Low-loss singlemode large mode area all-silica photonic bandgap fiber.

We describe the design and characterization of solid core large mode area bandgap fibers exhibiting low propagation loss and low bend loss. The fibers have been prepared by modified chemical vapor deposition process. The bandgap guidance obtained thanks to a 3-bilayer periodic cladding is assisted by a very slight index step (5.10-4) in the solid core. The propagation loss reaches a few dB/km and is found to be close to material loss.

Broadband dispersion-compensating fiber for high-bit-rate transmission network use.

The optimum refractive-index profile and drawing temperature were investigated so as to maximize the figure of merit for multicladding broadband dispersion-compensating fibers. Based on the results of the investigation, the authors have fabricated a highly bend-resistant fiber with a 92.6-ps/(nm dB) figure of merit using the modified chemical-vapor deposition method for dispersion compensation in the 1.5-1.6-µm wavelength region. The manufactured dispersion compensator does not suffer bend loss at 1.55 µm for curvatures of radia of 6.3 and 3.3 cm, and it has a 1.1-dB/km bend loss at a curvature of radius of 1.6 cm. Codoping the germanium silicate core with fluorine diminishes the optical loss down to 0.70 dB/km at a 1.55-µm wavelength.