Practical Guides for X-Ray Photoelectron Spectroscopy (XPS): First Steps in planning, conducting and reporting XPS measurements.

Over the past three decades, the widespread utility and applicability of X-ray photoelectron spectroscopy (XPS) in research and applications has made it the most popular and widely used method of surface analysis. Associated with this increased use has been an increase in the number of new or inexperienced users which has led to erroneous uses and misapplications of the method. This article is the first in a series of guides assembled by a committee of experienced XPS practitioners that are intended to assist inexperienced users by providing information about good practices in the use of XPS. This first guide outlines steps appropriate for determining whether XPS is capable of obtaining the desired information, identifies issues relevant to planning, conducting and reporting an XPS measurement, and identifies sources of practical information for conducting XPS measurements. Many of the topics and questions addressed in this article also apply to other surface-analysis techniques.

Fabrication and luminescence of ZnS:Mn2+ nanoflowers.

Visually striking nanoflowers composed of ZnS:Mn2+ nanoparticles are prepared and characterized. The configurations of these fractal structures are very sensitive to both the pH values of the particle solutions from which they are precipitated and the substrates on which they are deposited. At pH 2.2, the fractal structures resemble trees without leaves; at pH 7.7, they are tree-like with four arms and at pH 11.0 they resemble trees with six arms. High resolution transmission microscopy reveals that the nanoflowers are composed of ZnS:Mn2+ nanoparticles of 2-5 nm in size. X-ray photoelectron spectral data indicate that the sample compositions of nitrogen, chlorine, and sulfur vary gradually with pH values of the solutions. These changes may have an impact on both the fractal configuration and the luminescence properties. The emission spectra of the particle solutions at pH values of 2.2 and 11.0 are similar with the emission maximum at 475 nm. As the pH value approaches 7.7, the emission spectral maximum shifts to longer wavelengths. At a pH value of 7.7, the emission peak wavelength is the reddest, 520 nm. The emission peak of the nanoflowers at a pH value of 9.3 is 510 nm, while the emission spectrum of the nanoflowers at 5.2 has two peaks at 500 nm and 440 nm, respectively. These blue-green emissions are attributed to defects and are the dominant luminescence from the nanoflowers. The emission from Mn2+ dopant is only observed in the delayed spectra of the fractal solid samples.

Methanobactin, a copper-acquisition compound from methane-oxidizing bacteria.

Siderophores are extracellular iron-binding compounds that mediate iron transport into many cells. We present evidence of analogous molecules for copper transport from methane-oxidizing bacteria, represented here by a small fluorescent chromopeptide (C45N12O14H62Cu, 1216 daltons) produced by Methylosinus trichosporium OB3b. The crystal structure of this compound, methanobactin, was resolved to 1.15 angstroms. It is composed of a tetrapeptide, a tripeptide, and several unusual moieties, including two 4-thionyl-5-hydroxy-imidazole chromophores that coordinate the copper, a pyrrolidine that confers a bend in the overall chain, and an amino-terminal isopropylester group. The copper coordination environment includes a dual nitrogen- and sulfur-donating system derived from the thionyl imidazolate moieties. Structural elucidation of this molecule has broad implications in terms of organo-copper chemistry, biological methane oxidation, and global carbon cycling.

Electrochemically deposited sol-gel-derived silicate films as a viable alternative in thin-film design.

Sol-gel-derived silicate films were electrochemically deposited on conducting surfaces from a sol consisting of tetramethoxysilane (TMOS). In this method, a sufficiently negative potential is applied to the electrode surface to reduce oxygen to hydroxyl ions, which serves as the catalyst for the hydrolysis and condensation of TMOS. The electrodeposition process was followed by the electrochemical quartz crystal microbalance and cyclic voltammetry. The electrodeposited films were characterized for their surface morphology, porosity, and film thickness using atomic force microscopy, electrochemical probe techniques, surface area and pore size analysis, and profilometry. The electrodeposited films were found to have a completely different surface structure and to be significantly rougher relative to spin-coated films. This is likely due in part to the separation of the gelation and evaporation stages of film formation. The electrodeposited films were found to be permeable to simple redox molecules, such as ruthenium(III) hexaammine and ferrocene methanol. Film thickness can be easily varied from < 75 nm to > 15 microm by varying the electrode potential from -600 mV to more than -1000 mV, respectively. The electrodeposition process was further applied for the electroencapsulation of redox molecules and organic dyes within the silicate network. Cyclic voltammograms for the gel-entrapped ferrocene methanol (FcCH2OH) and ruthenium(II) tris(bipyridine) (Ru(bpy)3(2+)) exhibited the characteristic redox behavior of the molecules. The electroencapsulation of organic dyes in their "native" form proved to be more difficult because these species typically contain reducible functionalities that change the structure of the dye.