RESUMO
Commonly used S235JR structural steel, generally associated with good weldability, was joined by high-speed friction welding (HSFW). The friction welding tests were performed with a rotational speed of n = 8000 rpm and four different values of the unit pressure in the friction phase (pf) in the range of 64−255 MPa. The obtained joints were subjected to metallographic observations using an optical microscope; in selected zones of friction joints the average grain size was specified in accordance with the EN ISO 643:2012 standard; the hardness of friction joints was measured using the Vickers method. The friction-welded joint with the highest pf was EBSD-investigated. The obtained friction-welded joints resembled an hourglass, and the microstructure of individual zones of the joints differed depending on the height (axis, radius) of the observations. The generated joining conditions resulted in a significant refinement of the microstructure in the friction weldthe average grain size is about 1 µm2 (for base material it was 21 µm2). The highest increase in hardness above 340 HV0.1 was recorded in the friction weld of the welded joint with the lowest used value pressure in the friction phase. Such a sharp increase in hardness can make the resulting friction-welded joint become sensitive to dynamic or fatigue loads. The electron backscatter diffraction (EBSD) investigation confirmed the strong refinement of the microstructure in the friction-welded joint and the occurrence of the phenomenon of dynamic recrystallization (DRX). The friction weld was also characterized by a large share of high-angle boundaries (HAGBs) >80%. These results may indicate that during high-speed friction welding it is possible to create conditions like those obtained during the High-Pressure Torsion (the method used to produce UFG materials) process.
RESUMO
The article presents the results of research on the structural evolution of the composite Fe-Al-based coating deposited by arc spray with initial low participation of in situ intermetallic phases. The arc spraying process was carried out by simultaneously melting two different electrode wires, aluminum and low alloy steel (98.6 wt.% of Fe). The aim of the research was to reach protective coatings with a composite structure consisting of a significant participation of FexAly as intermetallic phases reinforcement. Initially, synthesis of intermetallic phases took place in situ during the spraying process. In the next step, participation of FexAly fraction was increased through the annealing process, with three temperature values, 700 °C, 800 °C, and 900 °C. Phase structure evolution of the Fe-Al arc-sprayed coating, stimulated by annealing, has been described by means of SEM images taken with a QBSD backscattered electron detector and by XRD and conversion electron Mössbauer spectroscopy (CEMS) investigations. Microhardness distribution of the investigated annealed coatings has been presented.
RESUMO
The paper presents the microstructural investigation of a friction-welded joint made of 316L stainless steel with an ultrafine-grained structure obtained by hydrostatic extrusion (HE). Such a plastically deformed material is characterized by a metastable state of energy equilibrium, increasing, among others, its sensitivity to high temperatures. This feature makes it difficult to weld ultra-fine-grained metals without losing their high mechanical properties. The use of high-speed friction welding and a friction time of <1 s reduced the scale of the weakening of the friction joint in relation to result obtained in conventional rotary friction welding. The study of changes in the microstructure of individual zones of the friction joint was carried out on an optical microscope (OM), scanning electron microscope (SEM), transmission electron microscope (TEM) and electron backscattered diffraction (EBSD) analysis system. The correlation between the microstructure and hardness of the friction joint is also presented. The heat released during the high-speed friction welding initiated the process of dynamic recrystallization (DRX) of single grains in the heat-affected zone (HAZ). The additional occurrence of strong plastic deformations (in HAZ) during flash formation and internal friction (in the friction weld and high-temperature HAZ) contributed to the formation of a highly deformed microstructure with numerous sub-grains. The zones with a microstructure other than the base material were characterized by lower hardness. Due to the complexity of the microstructure and its multifactorial impact on the properties of the friction-welded joint, strength should be the criterion for assessing the properties of the joint.
