Impedance Analysis and Noise Measurements on Multi Walled Carbon Nanotube Networks.

The electrical impedance characteristics of multi-walled carbon nanotube (MWCNTs) networks were studied as a function of CNT concentrations in the frequency range of 1 kHz-1 MHz. The novelty of this study is that the MWCNTs were not embedded in any polymer matrix and so the response of the device to electrical measurements are attributed to the CNTs in the network without any contribution from a polymer host matrix. Devices with low MWCNT packing density (0.31-0.85 µg/cm2) exhibit a frequency independent plateau in the low-frequency regime. At higher frequencies, the AC conductivity of these devices increases following a power law, characteristic of the universal dynamic response (UDR) phenomenon. On the other hand, devices with high MWCNT concentrations (>1.0 µg/cm2) exhibit frequency independent conductivity over the entire frequency range (up to 1 MHz), indicating that conduction in these devices is due to direct contact between the CNTs in the network. A simple single-relaxation time electrical equivalent circuit with an effective resistance and capacitance is used to describe the device performance. The electrical noise measurements on devices with different MWCNT packing densities exhibit bias-dependent low-frequency 1/f noise, attributed to resistance fluctuations.

Using a Novel Approach to Estimate Packing Density and Related Electrical Resistance in Multiwall Carbon Nanotube Networks.

In this work, we use contrast image processing to estimate the concentration of multi-wall carbon nanotubes (MWCNT) in a given network. The fractal dimension factor (D) of the CNT network that provides an estimate of its geometrical complexity, is determined and correlated to network resistance. Six fabricated devices with different CNT concentrations exhibit D factors ranging from 1.82 to 1.98. The lower D-factor was associated with the highly complex network with a large number of CNTs in it. The less complex network, having the lower density of CNTs had the highest D factor of approximately 2, which is the characteristic value for a two-dimensional network. The electrical resistance of the thin MWCNT network was found to scale with the areal mass density of MWCNTs by a power law, with a percolation exponent of 1.42 and a percolation threshold of 0.12 µg/cm2. The sheet resistance of the films with a high concentration of MWCNTs was about six orders of magnitude lower than that of less dense networks; an effect attributed to an increase in the number of CNT-CNT contacts, enabling more efficient electron transfer. The dependence of the resistance on the areal density of CNTs in the network and on CNT network complexity was analyzed to validate a two-dimension percolation behavior.

Design and Demonstration of High-Efficiency Quantum Well Solar Cells Employing Thin Strained Superlattices.

Nanostructured quantum well and quantum dot III-V solar cells provide a pathway to implement advanced single-junction photovoltaic device designs that can capture energy typically lost in traditional solar cells. To realize such high-efficiency single-junction devices, nanostructured device designs must be developed that maximize the open circuit voltage by minimizing both non-radiative and radiative components of the diode dark current. In this work, a study of the impact of barrier thickness in strained multiple quantum well solar cell structures suggests that apparent radiative efficiency is suppressed, and the collection efficiency is enhanced, at a quantum well barrier thickness of 4 nm or less. The observed changes in measured infrared external quantum efficiency and relative luminescence intensity in these thin barrier structures is attributed to increased wavefunction coupling and enhanced carrier transport across the quantum well region typically associated with the formation of a superlattice under a built-in field. In describing these effects, a high efficiency (>26% AM1.5) single-junction quantum well solar cell is demonstrated in a device structure employing both a strained superlattice and a heterojunction emitter.

Experimental and theoretical study of the optical and electrical properties of nanostructured indium tin oxide fabricated by oblique-angle deposition.

Oblique-angle deposition of indium tin oxide (ITO) is used to fabricate optical thin-film coatings with a porous, columnar nanostructure. Indium tin oxide is a material that is widely used in industrial applications because it is both optically transparent and electrically conductive. The ITO coatings are fabricated, using electron-beam evaporation, with a range of deposition angles between 0 degrees (normal incidence) and 80 degrees. As the deposition angle increases, we find that the porosity of the ITO film increases and the refractive index decreases. We measure the resistivity of the ITO film at each deposition angle, and find that as the porosity increases, the resistivity increases superlinearly. A new theoretical model is presented to describe the relationship between the ITO film's resistivity and its porosity. The model takes into account the columnar structure of the film, and agrees very well with the experimental data.

Growth of highly oriented ZnO nanowires on GaN substrates for electronic and optical sensor applications.

In this Paper we present growth and characterization results of highly oriented ZnO nanowires grown on wide bandgap GaN substrates. Experimental results on the ZnO nanowires grown on p-GaN are presented with growth morphology and dimensionality control. We also present experimental results on these nanowire arrays such as I-V measurements and UV sensitivity measurements. The ZnO nanowires can be used for a variety of nanoscale optical and electronics applications.

Gigantic enhancement in response and reset time of ZnO UV nanosensor by utilizing Schottky contact and surface functionalization.

UV response of ZnO nanowire nanosensor has been studied under ambient condition. By utilizing Schottky contact instead of Ohmic contact in device fabrication, the UV sensitivity of the nanosensor has been improved by four orders of magnitude, and the reset time has been drastically reduced from approximately 417 to approximately 0.8 s. By further surface functionalization with function polymers, the reset time has been reduced to approximately 20 ms even without correcting the electronic response of the measurement system. These results demonstrate an effective approach for building high response and fast reset UV detectors.

Patterned growth of horizontal ZnO nanowire arrays.

We report an approach to fabricating patterned horizontal ZnO nanowire arrays with a high degree of control over their dimensionality, orientation, and uniformity. Our method combines electron beam lithography and a low temperature hydrothermal decomposition. This approach opens up possibilities to fabricate ZnO NW array based strain and force sensors, two-dimensional photonic crystals, integrated circuit interconnects, and alternative current nanogenerators.