RESUMO
A unique nanomaterial has been developed for sweat analysis, including glucose level monitoring. Simple resusable low-cost sensors from composite materials based on graphene, hexagonal boron nitride, and conductive PEDOT:PSS (poly(3,4-ethylenedioxythiophene)polystyrene sulfonate) polymer have been developed and fabricated via 2D printing on flexible substrates. The sensors were tested as biosensors using different water-based solutions. A strong increase in the current response (several orders of magnitude) was observed for aqua vapors or glucose solution vapors. This property is associated with the sorption capacity of graphene synthesized in a volume of plasma jets and thus having many active centers on the surface. The structure and properties of graphene synthesized in a plasma are different from those of graphene created by other methods. As a result, the current response for a wearable sensor is 3-5 orders of magnitude higher for the reference blood glucose concentration range of 4-14 mM. It has been found that the most promising sensor with the highest response was fabricated based on the graphene:PEDOT:PSS composite. The graphene:h-BN:PEDOT:PSS (h-BN is hexagonal boron nitride) sensors demonstrated a longer response and the highest response after the functionalization of the sensors with a glucose oxidase enzyme. The reusable wearable graphene:PEDOT:PSS glucose sensors on a paper substrate demonstrated a current response of 10-10 to 10-5 A for an operating voltage of 0.5 V and glucose range of 4-10 mM.
RESUMO
During the pyrolysis of hydrocarbons in helium plasma jets in a plasma-chemical reactor, graphene flakes of a different structure and resistance were obtained. The presence of hydrogen in these structures was established by physicochemical methods, and its content depends on the pressure in the plasma-chemical reactor and the composition of a plasma-forming system. In addition to hydrogen, a relatively low concentration of oxygen atoms is present in the graphene flakes. Hydrogen is involved in the graphene nucleation, whereas oxygen is absorbed on graphene flakes from the air at low temperatures. It was found that a pressure increase in the reactor (up to 710 Torr) leads to the formation of flakes with a low resistivity (0.12-0.20 kOhm sq-1) and low defect density. In the case of synthesis at a low pressure (350-500 Torr), the resistance of graphene flakes is increased by three orders of magnitude (100-400 kOhm sq-1) with a more complicated defect structure and built-in hydrogen. Moreover, hydrogen is difficult to remove from these flakes, and annealing at relatively high temperatures (up to 300 °C) leads to a weak decrease in the resistance due to flake deformation. Additionally, the functionalization of the graphene flakes synthesized at a low pressure with fluorine atoms is suppressed due to their structural features. In general, the selection of growth parameters (gas pressure in a camera, flow rate and content of impurity atoms) allows one to control the defects in graphene, and its structure and conductivity.
RESUMO
The possibility of creating antennas of the 5G standard (5.2-5.9 GHz) with specified electrodynamic characteristics by printing layers of variable thickness using a graphene suspension has been substantiated experimentally and by computer simulation. A graphene suspension for screen printing on photographic paper and other flexible substrates was prepared by means of exfoliation from graphite. The relation between the graphene layer thickness and its sheet resistance was studied with the aim of determining the required thickness of the antenna conductive layer. To create a two-sided dipole, a technology has been developed for the double-sided deposition of graphene layers on photographic paper. The electrodynamic characteristics of graphene and copper antennas of identical design are compared. The antenna design corresponds to the operating frequency of 2.4 GHz. It was found that the use of graphene as a conductive layer made it possible to suppress the fundamental (first) harmonic (2.45 GHz) and to observe radiation at the second harmonic (5.75 GHz). This effect is assumed to observe in the case when the thickness of graphene is lower than that of the skin depth. The result indicates the possibility of changing the antenna electrodynamic characteristics by adjusting the graphene layer thickness.
RESUMO
The structure and electric properties of hexagonal boron nitride (h-BN):graphene composite with additives of the conductive polymer PEDOT:PSS and ethylene glycol were examined. The graphene and h-BN flakes synthesized in plasma with nanometer sizes were used for experiments. It was found that the addition of more than 10-3 mass% of PEDOT:PSS to the graphene suspension or h-BN:graphene composite in combination with ethylene glycol leads to a strong decrease (4-5 orders of magnitude, in our case) in the resistance of the films created from these suspensions. This is caused by an increase in the conductivity of PEDOT:PSS due to the interaction with ethylene glycol and synergetic effect on the composite properties of h-BN:graphene films. The addition of PEDOT:PSS to the h-BN:graphene composite leads to the correction of the bonds between nanoparticles and a weak change in the resistance under the tensile strain caused by the sample bending. A more pronounced flexibility of the composite films with tree components is demonstrated. The self-organization effects for graphene flakes and polar h-BN flakes lead to the formation of micrometer sized plates in drops and uniform-in-size nanoparticles in inks. The ratio of the components in the composite was found for the observed strong hysteresis and a negative differential resistance. Generally, PEDOT:PSS and ethylene glycol composite films are promising for their application as electrodes or active elements for logic and signal processing.
RESUMO
The possibility of graphene synthesis (the bottom-up approach) in plasma and the effective control of the morphology and electrical properties of graphene-based layers were demonstrated. Graphene flakes were grown in a plasma jet generated by a direct current plasma torch with helium and argon as the plasma-forming gases. In the case of argon plasma, the synthesized graphene flakes were relatively thick (2-6 nm) and non-conductive. In helium plasma, for the first time, graphene with a predominance of monolayer flakes and high conductivity was grown in a significant amount using an industrial plasma torch. One-dimensional (1D) flow modeling shows that the helium plasma is a less charged environment providing the formation of thinner graphene flakes with low defect density. These flakes might be used for a water-based suspension of the graphene with PEDOT:PSS (poly(3,4-ethylenedioxythiophene): polystyrene sulfonate) composite to create the structures employing the 2D printing technologies. Good structural quality, low layer resistance, and good mechanical strength combined with the ability to obtain a large amount of the graphene powder, and to control the parameters of the synthesized particles make this material promising for various applications and, above all, for sensors and other devices for flexible electronics and the Internet of things ecosystem.
RESUMO
A few-layer graphene-based hybrid material with high thermal and chemical stability and reproducible and tunable electronic properties was fabricated by intercalation of N-methylpyrrolidone into a few-layer graphene combined with heat treatment. Depending on the process temperature, the obtained material could be produced with the following properties: a broad range of resistivity values (six to seven orders of magnitude) in combination with a high carrier mobility, a tunable band-gap (from 0 up to 3-4 eV) and sp² or sp³ hybridization of carbon atoms. The extremely strong step-like temperature dependence (within 10 °C) of its properties observed in the vicinity of two temperatures, 90 and 200 °C, seems to be important for various applications. The hybrid material opens viable routes to progress in the design of three-dimensional nanostructures.
