Whey protein concentrate and skimmed milk powder as encapsulation agents for coffee silverskin extracts processed by spray drying.

We tested the hypothesis that milk proteins, through microencapsulation, guarantee protection against bioactive substances in coffee silverskin extracts. Therefore, the aim of this study was to carry out technological, nutritional and physicochemical characterisation of a coffee silverskin extract microencapsulated using instant skim milk powder and whey protein concentrate as wall materials. The aqueous extract of coffee silverskin was spray-dried using 10% (w/v) skim milk powder and whey protein concentrate. The samples were characterised by determining the water content, water activity, particle size distribution, colour analysis and total phenolic compound content as well as antioxidant activity using 2,2-diphenyl-radical 1-picrylhydrazyl scavenging methods, nitric oxide radical inhibition and morphological analysis. The product showed water activity within a range that ensured greater stability, and the reduced degradation of the dried coffee silverskin extract with whey protein concentrate resulted in better rehydration ability. The luminosity parameter was higher and the browning index was lower for the encapsulated samples than for the pure coffee silverskin extract. The phenolic compound content (29.23 ± 8.39 and 34.00 ± 8.38 mg gallic acid equivalents/g for the coffee silverskin extract using skimmed milk powder and whey protein concentrate, respectively) and the antioxidant activity of the new product confirmed its potential as a natural source of antioxidant phenolic compounds. We conclude that the dairy matrices associated with spray drying preserved the bioactive and antioxidant activities of coffee silverskin extracts.

The effect of homogenisation pressure on the microstructure of milk during evaporation and drying: particle-size distribution, electronic scanning microscopy, water activity and isotherm.

Homogenisation is a widely used technique in manufacturing powdered milk with a direct impact on product solubility, and the homogenisation pressure is a central attribute of this process. We aimed to understand the effect of increasing homogenisation pressures (0/0, 15/5, and 75/5 MPa, 1st/2nd stages) on particle-size distribution during homogenised whole milk powder manufacture and rehydration of the final product. The fluid milk was thermally treated, homogenised, concentrated by rotary evaporation, and then dried using a spray dryer. Particle size (Dv90) was monitored at all stages of the manufacturing process. The final product (milk powder) was analysed using particle-size distribution, electronic scanning microscopy, water activity, and isotherms. The results demonstrated that increasing the homogenisation pressure leads to milk powder with smaller particle size when rehydrated (Dv90 values: 6.08, 1.48 and 0.64 µm for 0, 20 and 80 MPa, respectively). Furthermore, the volume (%) of the particles in the 'sub-micro' region (smaller than 1.0 µm) presented an inversely proportional profile to the homogenisation pressure (homogenised fluid milk: 86.1, 29.3 and 2.4%; concentrated milk: 86.1, 26.5 and 5.7%, and reconstituted milk powder: 84.2, 31.8 and 10.9%). Surprisingly, this pattern was not observed in the SPAN value (which corresponds to the width or range of the size distribution based on the volume). Additionally, the increase in the homogenisation pressure did not affect the sorption isotherm pattern. These results demonstrate that increasing the homogenisation pressure decreases the particle size of the reconstituted powdered milk, indicating the potential for future studies on how this phenomenon affects its physicochemical and final product properties.

Stability of milk proteins subjected to UHT treatments: challenges and future perspectives.

Ultra-high temperature (UHT) treatments are of high economic relevance for food industries because they contribute to extending the shelf life of food products and facilitating their distribution. In the dairy segment, UHT treatments are applied to a wide range of products containing variable protein amounts. In this sense, the changes in the molecular structure of milk proteins induced by the severity of UHT treatments may lead to fouling in equipment during processing or sedimentation and/or gelation during storage. Nowadays, these concerns are even more relevant due to the increasing demand for UHT-treated high-protein beverages. This review will discuss the two main strategies used by industries to increase the stability of milk proteins during and/or after UHT treatments: (i) addition of chelating agents and (ii) use of polysaccharides. Moreover, the challenges and opportunities associated with promising strategies to improve the stability of milk proteins during and/or after UHT treatments will be covered in this review. The information compiled will be useful to guide researchers and industries in developing more stable UHT dairy products in harmony with consumers' demands.

Effects of calcium chloride substitution on the physicochemical properties of Minas Frescal cheese.

The aim in this research paper was to investigate the effect of using calcium monophosphate (MCP) and MCP mixed with commercial phosphates salts, in total or partial replacement of calcium chloride (CaCl2) in the manufacture of Minas Frescal cheese. Initially, model cheeses were made to perform the rheological analysis during the coagulation process. Of these, the five best treatments were chosen to carry out the production of Minas Frescal cheese, used only CaCl2 and MCP, and partial replacements of MCP + polyphosphate, MCP + potassium monophosphate (MKP) and MCP. The cheeses showed no significant difference in physicochemical composition, yield and syneresis, however, the cheese with partial replacement of CaCl2 by MCP + polyphosphate and MCP + MKP showed the highest hardness values, like the control. This demonstrates that it is possible to replace calcium chloride without significant changes in the physicochemical characteristics and yield of Minas Frescal cheese, and it is still possible to modulate the hardness of the cheese produced according to the type of calcium/phosphate source used. This allows the industry to replace the source of calcium in the manufacture of Minas Frescal cheese according to the desired hardness.

Edible insect as an alternative protein source: a review on the chemistry and functionalities of proteins under different processing methods.

The consumption of edible insects can be anadvantageous alternative to the conventional food supply chain, which involves global water waste, land deficit, undernutrition, and starvation. Besides the nutritional aspects, insect proteins have demonstrated a wide range of functional properties such as foamability, emulsifying and gelling abilities. The protein content and amino acid profile of some insects have revealed a good nutritional value and interesting functional properties. However, it is crucial to comprehend how the protein quality is affected by insect feeding, drying, and defatting. There is a knowledge gap about the impact of industrial treatment, such as pH, ionic strength, and heat treatment, on insect proteins' functional properties. In this review, we have aimed to highlight the potential application of insect proteins as a nutritional source and their promising technological applications. The study reported the principal insect protein characterization methodologies that have been investigated in the literature aiming to correlate the physicochemical parameters to possible protein functionalities. The research on the functional properties of insect proteins is at the exploratory level. Further detailed studies are needed to clarify the structure-function relation of insect proteins and how these functionalities and insect processing can increase consumer acceptance.

Colloidal stability of milk: reinterpretation of alcohol test results by digital microscopy.

In this research communication we propose a new approach by portable digital microscopy with a 200× objective to improve the visualization of microparticles of pasteurized milk submitted to the alcohol test. Not only did the method reduce the subjectivity of the readings, but also generated high resolution images of the microparticles, which allows the creation of a specific image pattern for each type of final product. In comparison to a control pasteurized milk treatment, the results confirmed the effect and the specificity of added salts (sodium citrate, disodium phosphate or their combination) on the stability of the milk to the alcohol test. Finally, the mixture of stabilizing salts of citrate/phosphate provided the highest degree of stability to pasteurized milk among the treatments studied.

Influence of sucrose reduction on fouling during the production of dulce de leche.

In this Research Communication we focus the food industry´s broad tendency to decrease sugar content in food products onto dulce de leche (DL) and examine the influence of sucrose reduction on the detrimental deposits formed during the production process. The method used to identify the impact produced directly on the heat exchanger during the production of this product with low sucrose content required varying the quantity of sucrose in the milk. Different percentages of sucrose (20, 15, 10, 5 and 0% w/w) were submitted to the DL concentration process in a process simulator. After concentration, the quantification of the deposits formed in each was carried out and these deposits were characterized according to their composition. Methods such as Kjeldahl, Pregl-Dumas and sem-EDS were used. Thus, the work highlights the need to change the product manufacturing process due to changes in the formulation that directly impact the formation of deposits in the equipment used (fouling). This deposit changes significantly in relation to its quantity as well as in relation to the composition and chemical characteristics as the gradual reduction of the sucrose content in the production takes place. Therefore, these impacts must be considered in order to maintain better manufacturing and ensure efficient cleaning of equipment.

Lactose-free Dulce de leche: compositional characterization, browning and texture profile.

Our objective was to elaborate lactose-free Dulce de leche (DL) and evaluate the influence of the hydrolysis of this sugar on the attributes of the products. Fluid milk used was divided into two portions and, in one of them, enzymatic hydrolysis of lactose was carried through. Next, the homogenization of milk was performed at 20 MPa. Four different treatments were studied. The final products were evaluated in relation to their composition and physico-chemical characteristics. The main results show that the homogenized lactose-free DL obtained a higher concentration of free 5-Hydroxymethylfurfural (HMF) (133.77 ± 3.42 µmol l-1). Consequently, browning was more intense due to Maillard Reaction. Texture parameters were higher (1611.00 ± 598.78 g hardness and 19.52 ± 2.46 g gumminess) when compared to the homogenized traditional product (28.45 ± 1.16 µmol l-1 free HMF, 437.17 ± 279.3 g hardness, and 406.20 ± 311.69 g gumminess). Lactose-free products are in high demand by consumers; however, the results of this work highlight the challenges to properly control the browning and the texture parameters of DL.

Recent patent applications in beverages enriched with plant proteins.

Recently, many consumers have been adding plant-based beverages to their diets, due to different reasons. The addition of plant proteins to enrich these products in order to make them more nutritionally balanced has become a trend, mainly because of their lower prices and reduced environmental damage. Thus, the aims of the present patent review are to discuss the potential of, and challenges posed by, plant proteins to the beverage industry, as well as to check market trends, focused on raw materials and beverage types. Based on the results, pea, rapeseed, bean, peanut, chickpea, lentil, hempseed, sunflower seed, and cottonseed were among the most often addressed raw materials. Furthermore, this enrichment process is not limited to create products that mimic dairy, therefore expansion in plant proteins used to enrich carbonated beverages, sports drinks, or even juices is expected to happen. Thus, plant-derived proteins have been promising to high-quality beverage production, as well as to ensure food security, animal welfare, and low environmental impacts.

Physical properties of UHT light cream: impact of the high-pressure homogenization and addition of hydrocolloids.

The beneficial effects of a healthy diet on the quality of life have prompted the food industry to develop low-fat variants, but fat content directly affects the physicochemical and sensory properties of food products. The utilization of high-pressure homogenization (HP) and incorporation of hydrocolloids have been suggested as strategies to improve the physical stability and rheological properties of light cream. Thus, this study aims to analyze the associated effect of high-pressure homogenization (80 MPa) and three different hydrocolloids: microcrystalline cellulose, locust bean gum and xanthan gum, on emulsion stability and rheological properties of ultra-high-temperature (UHT) light cream (ULC) with a 15% w/w fat content. The stability of ULC was determined by the ζ potential of oil droplets and emulsion stability percentage. Rheological characterization was based on flow behavior tests and dynamic oscillatory measurements, which were carried out in a rheometer. Results showed that the high-pressure homogenization process did not influence the emulsion stability of the treatments. Moreover, the hydrocolloids added to systems present weak interactions with milk proteins since all ULC showed macroscopical phase separation. The samples presented the same rheological behavior and were classified as pseudoplastic fluids (n < 1). ULC treated at 80 MPa was significantly (P ≤ 0.05) more consistent than the treatments at 20 MPa. All ULC showed a predominant elastic behavior (G' > G″), and a remarkable increase in both G' and G″ at 80 MPa. The results presented in this study highlight the potential of HP for altering some rheological characteristics of UHT light cream, for example, to increase its consistency. These results are important for the dairy industry and ingredient suppliers, in the standardization of UHT light cream and/or to develop low-fat products.

5-Hydroxymethylfurfural formation and color change in lactose-hydrolyzed Dulce de leche.

The work described in this Research Communication concerns the production of Dulce de leche (DL), that is a traditional product from South America obtained by concentration. Maillard reaction (MR) products are mainly responsible for the formation of color and flavor in this product. Lactose-hydrolyzed products have been developed to supply consumer demand, but this hydrolysis may affect the flavor, color, taste, texture and even some nutritional aspects of the product. We studied the influence of different levels of lactose-hydrolysis, sucrose addition and initial pH on the development of MR, appraised by the determination of 5-hydroxymethylfurfural (HMF). A process simulator with multi-monitoring system was used to produce 15 DL. Box-Behnken 33 experimental design was applied for the three factors: pH, lactose-hydrolysis level and sucrose concentration. Lipids, protein, ashes, carbohydrates, water activity, dissolved solids, colorimetric analysis and HMF (free and total) are among the physicochemical attributes and MR indicators analyzed in this work. The products showed significant differences in composition but all the values were in agreement with the literature. Moreover, higher levels of lactose hydrolysis and higher pH presented a direct relation with the development of MR, observed by an increase in coloration (lower luminosity) and more formation of HMF, both free and total. The present study expands the knowledge about DL spread made of lactose-hydrolyzed milk, allowing the food industries to produce a lactose free DL with nutritional and sensory characteristics closer to the traditional product.

Technological aspects of lactose-hydrolyzed milk powder.

Few reports describe the effect of lactose hydrolysis on the properties of milk powder during production and storage. Hence, the aim of this study was to evaluate the effects of five different levels of enzymatic lactose hydrolysis during the production and storage of milk powder. As the lactose hydrolysis rate increased, adhesion to the drying chamber also increased, due to higher levels of particle agglomeration. Additionally, more brown powder was obtained when the lactose hydrolysis rate was increased, which in turn negatively affected rehydration ability. Using Raman spectroscopy, crystallization of the lactose residues in various samples was assessed over 6weeks of accelerated aging at a room temperature environment with 75.5% of air moisture. Products with 25% or greater lactose hydrolysis showed no signs of crystallization, in contrast to the non-hydrolyzed sample.

Supplementation with concentrated milk protein in patients undergoing hematopoietic stem cell transplantation.

OBJECTIVE: The aim of this study was to analyze the influence of dietary supplementation with whey protein concentrate (WPC) in the incidence of oral mucositis (OM) in patients undergoing hematopoietic stem cell transplantation (HSCT). METHODS: Patients were supplemented with a daily intake of WPC delivering 50% of the daily protein requirements (DPR) according to the Dietary Reference Intakes and classified later based on the amount of ingested supplement until OM median onset. RESULTS: We evaluated 73 patients. Forty-three were part of the historical control and 30 were supplemented with WPC. The OM had a mean duration of 5.3 d (SD 4.5), ranging from the day of the infusion of stem cells until the 17th day after infusion and a median of 5 d after infusion. OM duration was influenced by the conditioning protocol (P < 0.01) and WPC (P = 0.01). Patients who consumed the WPC in an amount ≥40% of DPR had a 35% reduction in duration of OM, and the incidence of OM grades 3 and 4 was 11 times smaller. Body mass index, serum albumin, and adverse reactions, such as diarrhea, nausea and vomiting, dysphagia, dry mouth and drooling, showed no statistically significant differences. CONCLUSION: WPC intake ≥40% of DPR helped to reduce the severity and duration of OM. The use of WPC in patients undergoing HSCT was shown to be safe, encouraging new studies in this population to assess its action mechanism.

Analysis of spreadable cheese by Raman spectroscopy and chemometric tools.

In this work, FT-Raman spectroscopy was explored to evaluate spreadable cheese samples. A partial least squares discriminant analysis was employed to identify the spreadable cheese samples containing starch. To build the models, two types of samples were used: commercial samples and samples manufactured in local industries. The method of supervised classification PLS-DA was employed to classify the samples as adulterated or without starch. Multivariate regression was performed using the partial least squares method to quantify the starch in the spreadable cheese. The limit of detection obtained for the model was 0.34% (w/w) and the limit of quantification was 1.14% (w/w). The reliability of the models was evaluated by determining the confidence interval, which was calculated using the bootstrap re-sampling technique. The results show that the classification models can be used to complement classical analysis and as screening methods.

FT-Raman and chemometric tools for rapid determination of quality parameters in milk powder: Classification of samples for the presence of lactose and fraud detection by addition of maltodextrin.

FT-Raman spectroscopy has been explored as a quick screening method to evaluate the presence of lactose and identify milk powder samples adulterated with maltodextrin (2.5-50% w/w). Raman measurements can easily differentiate samples of milk powder, without the need for sample preparation, while traditional quality control methods, including high performance liquid chromatography, are cumbersome and slow. FT-Raman spectra were obtained from samples of whole lactose and low-lactose milk powder, both without and with addition of maltodextrin. Differences were observed between the spectra involved in identifying samples with low lactose content, as well as adulterated samples. Exploratory data analysis using Raman spectroscopy and multivariate analysis was also developed to classify samples with PCA and PLS-DA. The PLS-DA models obtained allowed to correctly classify all samples. These results demonstrate the utility of FT-Raman spectroscopy in combination with chemometrics to infer about the quality of milk powder.

Evaluation of the synergistic effects of milk proteins in a rapid viscosity analyzer.

Protein systems (PS) are routinely used by companies from Brazil and around the globe to improve the texture, yield, and palatability of processed foods. Understanding the synergistic behavior among the different protein structures of these systems during thermal treatment under the influence of pH can help to better define optimum conditions for products and processes. The interpretation of the reactions and interactions that occur simultaneously among the protein constituents of these systems as dispersions during thermal processing is still a major challenge. Here, using a rapid viscosity analyzer, we observed the rheological changes in the startup viscosities of 5 PS obtained by combining varying proportions of milk protein concentrate and whey protein concentrate under different conditions of pH (5.0, 6.5, and 7.0) and heat processing (85°C/15min and 95°C/5min). The solutions were standardized to 25% of total solids and 17% of protein. Ten analytical parameters were used to characterize each of the startup-viscosity ramps for 35 experiments conducted in a 2×3 × 5 mixed planning matrix, using principal component analysis to interpret behavioral similarities. The study showed the clear influence of pH 5.5 in the elevation of the initial temperature of the PS startup viscosity by at least 5°C, as well as the effect of different milk protein concentrate:whey protein concentrate ratios above 15:85 at pH 7.0 on the viscographic profile curves. These results suggested that the primary agent driving the changes was the synergism among the reactions and interactions of casein with whey proteins during processing. This study reinforces the importance of the rapid viscosity analyzer as an analytical tool for the simulation of industrial processes involving PS, and the use of the startup viscosity ramp as a means of interpreting the interactions of system components with respect to changes related to the treatment temperature.

Classification of frankfurters by FT-Raman spectroscopy and chemometric methods.

Frankfurters are widely consumed all over the world, and the production requires a wide range of meat and non-meat ingredients. Due to these characteristics, frankfurters are products that can be easily adulterated with lower value meats, and the presence of undeclared species. Adulterations are often still difficult to detect, due the fact that the adulterant components are usually very similar to the authentic product. In this work, FT-Raman spectroscopy was employed as a rapid technique for assessing the quality of frankfurters. Based on information provided by the Raman spectra, a multivariate classification model was developed to identify the frankfurter type. The aim was to study three types of frankfurters (chicken, turkey and mixed meat) according to their Raman spectra, based on the fatty vibrational bands. Classification model was built using partial least square discriminant analysis (PLS-DA) and the performance model was evaluated in terms of sensitivity, specificity, accuracy, efficiency and Matthews's correlation coefficient. The PLS-DA models give sensitivity and specificity values on the test set in the ranges of 88%-100%, showing good performance of the classification models. The work shows the Raman spectroscopy with chemometric tools can be used as an analytical tool in quality control of frankfurters.

Determination of amylose content in starch using Raman spectroscopy and multivariate calibration analysis.

Fourier transform Raman spectroscopy and chemometric tools have been used for exploratory analysis of pure corn and cassava starch samples and mixtures of both starches, as well as for the quantification of amylose content in corn and cassava starch samples. The exploratory analysis using principal component analysis shows that two natural groups of similar samples can be obtained, according to the amylose content, and consequently the botanical origins. The Raman band at 480 cm(-1), assigned to the ring vibration of starches, has the major contribution to the separation of the corn and cassava starch samples. This region was used as a marker to identify the presence of starch in different samples, as well as to characterize amylose and amylopectin. Two calibration models were developed based on partial least squares regression involving pure corn and cassava, and a third model with both starch samples was also built; the results were compared with the results of the standard colorimetric method. The samples were separated into two groups of calibration and validation by employing the Kennard-Stone algorithm and the optimum number of latent variables was chosen by the root mean square error of cross-validation obtained from the calibration set by internal validation (leave one out). The performance of each model was evaluated by the root mean square errors of calibration and prediction, and the results obtained indicate that Fourier transform Raman spectroscopy can be used for rapid determination of apparent amylose in starch samples with prediction errors similar to those of the standard method.

Spectroscopic and theoretical study of the "azo"-dye E124 in condensate phase: evidence of a dominant hydrazo form.

Spectroscopic techniques, including Raman, IR, UV/vis, and NMR were used to characterize the samples of the azo dye Ponceau 4R (also known as E124, New Coccine; Cochineal Red; C.I. no. 16255; Food Red No. 102), which is 1,3-naphthalenedisulfonic acid, 7-hydroxy-8-[(4-sulfo-1-naphthalenyl) azo] trisodium salt in aqueous solution and solid state. In addition, first principle calculations were carried out for the azo (OH) and hydrazo (NH) tautomers in order to assist in the assignment of the experimental data. The two intense bands observed in the UV/vis spectrum, centered at 332 and 507 nm, can be compared to the calculated values at 296 and 474 nm for azo and 315 and 500 nm for hydrazo isomer, with the latter in closer agreement to the experiment. The Raman spectrum is quite sensitive to tautomeric equilibrium; in solid state and aqueous solution, three bands were observed around 1574, 1515, and 1364 cm(-1), assigned to mixed modes including deltaNH + betaCH + nuCC, deltaNH + nuC horizontal lineO + nuC horizontal lineN + betaCH and nuCC vibrations, respectively. These assignments are predicted only for the NH species centered at 1606, 1554, and 1375 cm(-1). The calculated Raman spectrum for the azo (OH) tautomer showed two strong bands at 1468 (nuN = N + deltaOH) and 1324 cm(-1) (nuCC + nuC-N), which were not obtained experimentally. The (13)C NMR spectrum showed a very characteristic peak at 192 ppm assigned to the carbon bound to oxygen in the naphthol ring; the predicted values were 165 ppm for OH and 187 for NH isomer, supporting once again the predominance of NH species in solution. Therefore, all of the experimental and theoretical results strongly suggest the food dye Ponceau 4R or E124 has a major contribution of the hydrazo structure instead of the azo form as the most abundant in condensate phase.