Numerical design and characterization of a novel parallel beam combined lens based on X-ray capillary optics.

A novel parallel beam combined lens (PBCL) was designed based on a parabolic monocapillary x-ray lens (PMXRL). The proposed PBCL converted a divergent X-ray beam into a near-solid parallel one, which retains the low divergence characteristics of PMXRL and significantly improves the intensity gain by about one order of magnitude. Compared with the traditional polycapillary parallel x-ray lens (PPXRL), the divergence performance of this lens is improved by an order of magnitude, and the light intensity gain is improved by 3-4 times. In addition, we developed a MATLAB-based visualization tool to simulate X-ray transmission within the PBCL through ray tracing. This tool facilitated the assessment of the PBCL's transmission efficiency and its comparison with conventional PMXRL and the PPXRL. The transport process of the PBCL is systematically investigated under the comprehensive consideration of multiple parameters. This study provided a new idea and theoretical basis for the further development of X-ray modulation technology.

Magnified x ray ghost imaging with tapered polycapillary optics free of the penumbra effect.

X ray ghost imaging (XGI) offers both radiation dose-reduction potential and cost-effective benefits owing to the utilization of a single-pixel detector. Most XGI schemes with laboratory x ray sources require a mechanically moving mask for either structured illumination or structured detection. In either configuration, however, its resolution remains limited by the source size and the unit size of the mask. Upon propagation, the details of the object can actually be magnified by the divergence of x rays, but at the same time, the penumbra effect produced by the finite source size is dramatically intensified, which ultimately leads to a degradation of image quality in XGI. To address these limitations, this work proposes a magnified XGI scheme using structured detection equipped with tapered polycapillary optics, which can efficiently suppress the object's penumbra as well as resolve the magnified details of the object. In general, the resolution of this scheme is no longer affected by the source size but by the microcapillary size of polycapillary. Our work fundamentally achieves cancellation of penumbra effect-induced aberration, thus paving the way for high-resolution magnified XGI.

Determination of Hepatic Iron Deposition in Drug-Induced Liver Fibrosis in Rats by Confocal Micro-XRF Spectrometry.

Liver fibrosis is the intermediate process and inevitable stage of the development of chronic liver disease into cirrhosis. Reducing the degree of liver fibrosis plays an extremely important role in treating chronic liver disease and preventing liver cirrhosis and liver cancer. The formation of liver fibrosis is affected by iron deposition to a certain extent, and excessive iron deposition further induces liver cirrhosis and liver cancer. Herein, confocal microbeam X-ray fluorescence (µ-XRF) was used to determine the intensity and biodistribution of iron deposition at different time points in the process of liver fibrosis induced by thioacetamide (TAA) in rats. To our best knowledge, this is the first study using confocal µ-XRF to analyze hepatic iron deposition in hepatic fibrosis. The results showed that there are minor and trace elements such as iron, potassium, and zinc in the liver of rats. Continuous injection of TAA solution resulted in increasing liver iron deposition over time. The intensity of iron deposition in liver tissue was also significantly reduced after bone mesenchymal stem cells (BMSCs) were injected. These findings indicated that confocal µ-XRF can be used as a nondestructive and quantitative method of evaluating hepatic iron deposition in hepatic fibrosis, and iron deposition may play an important role in the progression of hepatic fibrosis induced by TAA.

Fast method for computing a system matrix using a polar-coordinate pixel model with concentric annuluses of different radial widths.

Despite better reconstruction quality for incomplete or noisy projection data compared to analytic reconstruction, computed tomography iterative techniques are time-consuming, mainly due to high system matrix computation. A polar-coordinate pixel model with concentric annuluses of different radial widths was established and a fast method for computing the system matrix was presented based on characteristics of this model. Compared with the Siddon algorithm and an efficient Cartesian algorithm introduced by Zhang, the proposed algorithm based on the simultaneous algebraic reconstruction technique shows speed advantages for both numerical simulation and experiment, without noticeable loss of image quality.

Measurement of the inner diameter of monocapillary with confocal x-ray scattering technology based on capillary x-ray optics.

The inner diameter is one of most important parameters in the design and fabrication of monocapillary x-ray optics, which are widely used in x-ray technology. The confocal x-ray scattering method based on x-ray capillary optics was proposed to nondestructively measure the inner and outer diameters of the monocapillary. The positions of the boundaries of monocapillary x-ray optics were determined by a knife-edge scanning method, and the x-ray optics were profiled in two planes or in three-dimensional space accordingly. This confocal method could conveniently give the inner surface topography of the monocapillary optics, which can be used to show the difference between the actual inner surface and the theoretical one, and has potential applications in nondestructive measurements of stratified substances, or the profile morphology of a specific interface.

Confocal total reflection X-ray fluorescence technology based on an elliptical monocapillary and a parallel polycapillary X-ray optics.

A total reflection X-ray fluorescence (TXRF) spectrometer based on an elliptical monocapillary X-ray lens (MXRL) and a parallel polycapillary X-ray lens (PPXRL) was designed. This TXRF instrument has micro focal spot, low divergence and high intensity of incident X-ray beam. The diameter of the focal spot of MXRL was 16.5 µm, and the divergence of the incident X-ray beam was 3.4 mrad. We applied this TXRF instrument to the micro analysis of a single-layer film containing Ni deposited on a Si substrate by metal vapor vacuum arc ion source.

Confocal depth-resolved fluorescence micro-X-ray absorption spectroscopy for the study of cultural heritage materials: a new mobile endstation at the Beijing Synchrotron Radiation Facility.

A confocal fluorescence endstation for depth-resolved micro-X-ray absorption spectroscopy is described. A polycapillary half-lens defines the incident beam path and a second polycapillary half-lens at 90° defines the probe sample volume. An automatic alignment program based on an evolutionary algorithm is employed to make the alignment procedure efficient. This depth-resolved system was examined on a general X-ray absorption spectroscopy (XAS) beamline at the Beijing Synchrotron Radiation Facility. Sacrificial red glaze (AD 1368-1644) china was studied to show the capability of the instrument. As a mobile endstation to be applied on multiple beamlines, the confocal system can improve the function and flexibility of general XAS beamlines, and extend their capabilities to a wider user community.

Energy-dispersive small-angle X-ray scattering with cone collimation using X-ray capillary optics.

Energy-dispersive small-angle X-ray scattering (ED-SAXS) with an innovative design of cone collimation based on an ellipsoidal single-bounce capillary (ESBC) and a polycapillary parallel X-ray lens (PPXRL) had been explored. Using this new cone collimation system, scattering angle 2θ has a theoretical minimum angle related to the mean half-opening angle of the hollow cone beam of 1.42 mrad, and with the usable X-ray energy ranging from 4 to 30 keV, the resulting observable scattering vector q is down to a minimum value of about 0.003 Å-1 (or a Bragg spacing of about 2100 Å). However, the absorption of lower energies by X-ray capillary optics, sample transmission, and detector response function limits the application range to lower energy. Cone collimation ED-SAXS experiments carried out on pure water, Lupolen, and in situ temperature-dependent measurement of diacetylenic acid/melamine micelle solid were presented at three different scattering angles 2θ of 0.18°, 0.70° and 1.18° to illustrate the new opportunities offered by this technique as well as its limitations. Also, a comparison has been made by replacing the PPXRL with a pinhole, and the result shows that cone collimation ED-SAXS based on ESBC with PPXRL was helpful in improving the signal-to-noise ratio (i.e., reducing the parasitic background scattering) than ESBC with a pinhole. The cone collimation instrument based on X-ray capillary optics could be considered as a promising tool to perform SAXS experiments, especially cone collimation ED-SAXS has potential application for the in situ temperature-dependent studying on the kinetics of phase transitions.

Authentication of vegetable oils by confocal X-ray scattering analysis with coherent/incoherent scattered X-rays.

This paper presents an alternative analytical method based on the Rayleigh to Compton scattering intensity ratio and effective atomic number for non-destructive identification of vegetable oils using confocal energy dispersive X-ray fluorescence and scattering spectrometry. A calibration curve for the Rayleigh to Compton scattering intensity ratio and effective atomic number was constructed on the basis of a reliable physical model for X-ray scattering. The content of light elements, which are "invisible" using X-ray fluorescence, can be calculated "by difference" from the calibration curve. In this work, we demonstrated the use of this proposed approach to identify complex organic matrices in different vegetable oils with high precision and accuracy.

Focal construct geometry for high intensity energy dispersive x-ray diffraction based on x-ray capillary optics.

We presented a focal construct geometry (FCG) method for high intensity energy dispersive X-ray diffraction by utilizing a home-made ellipsoidal single-bounce capillary (ESBC) and a polycapillary parallel X-ray lens (PPXRL). The ESBC was employed to focus the X-rays from a conventional laboratory source into a small focal spot and to produce an annular X-ray beam in the far-field. Additionally, diffracted polychromatic X-rays were confocally collected by the PPXRL attached to a stationary energy-resolved detector. Our FCG method based on ESBC and PPXRL had achieved relatively high intensity diffraction peaks and effectively narrowed the diffraction peak width which was helpful in improving the potential d-spacing resolution for material phase analysis.

[Application of Three Dimensional Confocal Micro X-Ray Fluorescence Technology Based on Polycapillary X-Ray Lens in Analysis of Rock and Mineral Samples].

Confocal three dimensional (3D) micro X-ray fluorescence (XRF) spectrometer based on a polycapillary focusing X-ray lens (PFXRL) in the excitation channel and a polycapillary parallel X-ray lens (PPXRL) in the detection channel was developed. The PFXRL and PPXRL were placed in a confocal configuration. This was helpful in improving the signal-to-noise ratio of the XRF spectra, and accordingly lowered the detection limitation of the XRF technology. The confocal configuration ensured that only the XRF signal from the confocal micro-volume overlapped by the output focal spot of the PFXRL and the input focal spot of the PPXRL could be detected by the detector. Therefore, the point-to-point information of XRF for samples could be obtained non-destructively by moving the sample located at the confocal position. The magnitude of the gain in power density of the PFXRL was 10(3). This let the low power conventional X-ray source be used in this confocal XRF, and, accordingly, decreased the requirement of high power X-ray source for the confocal XRF based on polycapillary X-ray optics. In this paper, we used the confocal 3D micro X-ray fluorescence spectrometer to non-destructively analyzed mineral samples and to carry out a 3D point-to-point elemental mapping scanning, which demonstrated the capabilities of confocal 3D micro XRF technology for non-destructive analysis elements composition and distribution for mineral samples. For one mineral sample, the experimental results showed that the area with high density of element of iron had high density of copper. To some extent, this reflected the growth mechanisms of the mineral sample. The confocal 3D micro XRF technology has potential applications in such fields like the analysis identification of ore, jade, lithoid utensils, "gamble stone" and lithoid flooring.

Monochromatic X-ray imaging using a combination of doubly curved crystal and polycapillary X-ray lens.

A monochromatic X-ray imaging setup based on a combination of a doubly curved crystal and a polycapillary focusing X-ray lens was designed. In this setup, the bent crystal optic was used not only to monochromatize but also to focus the divergent X-ray beam from a conventional X-ray source to form a monochromatic X-ray focal spot with a size of 426 × 467 µm2 at 17.5 keV. The beam expanding from this focal point was focused by the polycapillary optic to obtain a focal spot which was then used as the monochromatic X-ray imaging virtual source. The output focal spot size of the focusing polycapillary optic at 17.5 keV was 97 µm. Compared with the beam expansion after the focal spot of the bent crystal optic, the beam expansion after the focal spot of the focusing polycapillary optic was relatively large. This was helpful for magnifying the X-ray image of the sample. The focused beam was helpful to decrease the exposure time for imaging small samples.

Adjustable hollow-cone output x-ray beam from an ellipsoidal monocapillary with a pinhole and a beam stop.

A combined shading system (CSS) consisting of a beam stop and a pinhole is proposed to be used between an ellipsoidal monocapillary (EM) and a conventional laboratory x-ray source to obtain an adjustable hollow-cone output beam for different experiments with no need for changing the EM. The CSS can change the incident x-ray beam on the EM by adjusting the position of the beam stop and the pinhole, with the corresponding change of the output beam of the EM. In this study, the adjustable hollow-cone output x-ray beam of an 80-mm-long EM with a CSS was studied in detail with a laboratory Cu x-ray generator with a focal spot diameter of 50 µm. The adjustable range of the focal spot size of the EM was from 8.6 to 58.7 µm. The adjustable range of the gain of the focal spot of the EM was from 0 to 1350. The beam divergence of the hollow-cone output beam of the EM ranged from 6 to 16.75 mrad. The illumination angle of the hollow-cone output beam of the EM ranged from 0 to 5.95 mrad. In addition, the potential application of the proposed adjusting method in testing the performance of the EM is briefly discussed.

Application of confocal X-ray fluorescence micro-spectroscopy to the investigation of paint layers.

A confocal micro X-ray fluorescence (MXRF) spectrometer based on polycapillary X-ray optics was used for the identification of paint layers. The performance of the confocal MXRF was studied. Multilayered paint fragments of a car were analyzed nondestructively to demonstrate that this confocal MXRF instrument could be used in the discrimination of the various layers in multilayer paint systems.

In-situ and elementally resolved determination of the thickness uniformity of multi-ply films by confocal micro XRF.

Confocal micro X-ray fluorescence (CM-XRF) with quasi-monochromatic excitation based on polycapillary X-ray optics was used to measure the thickness of multi-ply films. The relative errors of measuring an Fe film with a thickness of 16.3 µm and a Cu film with a thickness of 24.5 µm were 7.3% and 0.4%, respectively. The non-destructive and in-situ measurement of the thickness and uniformity of multi-ply films of Cu, Fe and Ni on a silicon surface was performed. CM-XRF was convenient in in-situ and elementally resolved analysis of the thickness of multi-ply films without a cumbersome theoretical correction model.

Spatially resolved in situ measurements of the ion distribution near the surface of electrode in a steady-state diffusion in an electrolytic tank with confocal micro X-ray fluorescence.

Confocal micro-X-ray fluorescence (MXRF) technology based on a polycapillary focusing X-ray lens and a polycapillary parallel X-ray lens was used to carry out element-resolved and in situ analysis of ion distribution near the surface of the electrode in a steady-state diffusion in an electrolytic tank. The standard curve of the Cu Kα fluorescence intensity corresponding to the concentration of CuCl2 was measured to quantitatively determine the ion distribution near the surface of the electrode in a steady-state diffusion. The distribution of the electrolytic ions around the surface of the electrode in the electrolytic tank was measured in situ, and the effects of the concentration of the electrolyte and the bath voltage on the shape of the layer with a nonuniform distribution of the Cu(2+) ions near the cathode surface in a steady state were analyzed with the confocal MXRF. The confocal MXRF has potential applications in spatially resolved analysis of the liquid mass transfer in electrolytic tanks in situ.

[Application of confocal technology based on polycapillary X-ray lens in measuring thickness].

A confocal micro X-ray fluorescence thickness gauge based on a polycapillary focusing X-ray lens, a polycapillary parallel X-ray lens and a laboratory X-ray source was designed in order to analyze nondestructively the thickness of thin film and cladding material. The performances of this confocal thickness gauge were studied. Two Ni films with a thickness of about 25 and 15 microm respectively were measured. The relative errors corresponding to them were 3.5% and 7.1%, respectively. The thickness uniformity of a Ni films with a thickness of about 10 microm was analyzed. This confocal technology for measuring the thickness was both spatially resolved and elemental sensitive, and therefore, it could be used to measure the thickness of the multilayer sample and analyze the thickness uniformity of the sample. This confocal thickness gauge had potential applications in analyzing the thickness of sample.

Full-field transmission x-ray imaging with confocal polycapillary x-ray optics.

A transmission x-ray imaging setup based on a confocal combination of a polycapillary focusing x-ray optic followed by a polycapillary collimating x-ray optic was designed and demonstrated to have good resolution, better than the unmagnified pixel size and unlimited by the x-ray tube spot size. This imaging setup has potential application in x-ray imaging for small samples, for example, for histology specimens.

[Application of confocal micro-beam X-ray fluorescence in nondestructive scanning analysis of the distribution of elements in a single hair].

The confocal micro X-ray fluorescence (XRF) based on polycapillary X-ray lens and conventional X-ray source was used to carry out the scanning analysis of the distribution of the elements in a single hair. The elemental distribution in the single hair was obtained. In the confocal micro XRF technology, the output focal spot of the polycapillary focusing X-ray lens and the input focal spot of the polycapillary parallel X-ray lens were adjusted confocally. The detector could only detect the X-rays from the overlapping foci. This confocal structure decreased the effects of the background on the X-ray spectra, and was accordingly helpful for improving the accuracy of this XRF technology. A polycapillary focusing X-ray lens with a high gain in power density was used to decrease the requirement of power of the X-ray source used in this confocal technology, and made it possible to perform such confocal micro XRF analysis by using the conventional X-ray source with low cost. Experimental results indicated that the confocal micro X-ray fluorescence based on polycapillary X-ray lens had potential applications in analyzing the elemental distribution of individual hairs.

Focusing synchrotron radiation using a polycapillary half-focusing X-ray lens for imaging.

An imaging system based on a polycapillary half-focusing X-ray lens (PHFXRL) and synchrotron radiation source has been designed. The focal spot size and the gain in power density of the PHFXRL were 22 microm (FWHM) and 4648, respectively, at 14.0 keV. The spatial resolution of this new imaging system was better than 5 microm when an X-ray charge coupled device with a pixel size of 10.9 x 10.9 microm was used. A fossil of an ancient biological specimen was imaged using this system.