Antibacterial effect of bactericide immobilized in resin matrix.

OBJECTIVE: Biomaterials with anti-microbial properties are highly desirable in the oral cavity. Ideally, bactericidal molecules should be immobilized within the biomaterial to avoid unwanted side-effects against surrounding tissues. They may then however loose much of their antibacterial efficiency. The aim of this study was to investigate how much antibacterial effect an immobilized bactericidal molecule still has against oral bacteria. METHODS: Experimental resins containing 0, 1 and 3% cetylpyridinium chloride (CPC) were polymerized, and the bacteriostatic and bactericidal effects against Streptococcus mutans were determined. Adherent S. mutans on HAp was quantitatively determined using FE-SEM and living cells of S. mutans were quantified using real-time RT-PCR. The amount of CPC released from the 0%-, 1%- and 3%-CPC resin sample into water was spectrometrically quantified using a UV-vis recording spectrophotometer. RESULTS: UV spectrometry revealed that less than 0.11 ppm of CPC was released from the resin into water for all specimens, which is lower than the minimal concentration generally needed to inhibit biofilm formation. Growth of S. mutans was significantly inhibited on the surface of the 3%-CPC-containing resin coating, although no inhibitory effect was observed on bacteria that were not in contact with its surface. When immersed in water, the antibacterial capability of 3%-CPC resin lasted for 7 days, as compared to resin that did not contain CPC. SIGNIFICANCE: These results demonstrated that the bactericidal molecule still possessed significant contact bacteriostatic activity when it was immobilized in the resin matrix.

In vitro apatite formation on organic polymers modified with a silane coupling reagent.

Gamma-methacryloxypropyltrimethoxysilane (gamma-MPS) was grafted to high-density polyethylene, polyamide and silicone rubber substrates by the emulsion polymerization procedure in order to provide these organic polymers with in vitro apatite-forming ability. The contact angles towards distilled water of the gamma-MPS-grafted specimens were lower than those of the original organic polymer specimens, indicating that the grafted substrates were more hydrophilic. The in vitro apatite formation in a simulated body fluid (Kokubo solution) was confirmed for several of the gamma-MPS-grafted specimens.

Selective protein adsorption and blood compatibility of hydroxy-carbonate apatites.

We examined the blood compatibility and protein adsorption on hydroxyapatite and hydroxy-carbonate apatite. Those apatites were synthesized under a 0, 5, or 15% CO(2)-containing N(2) atmosphere by a wet-chemical method with a strong ammonia alkali solution of calcium nitrate and diammonium hydrogen phosphate (5:3 in molar ratio) and subsequent calcination in the range of 105-700 degrees C. From infrared (IR) analysis, the carbonate ions substituted both phosphate ions and hydroxyl ions in the hydroxyapatite lattice; the intensities of IR bands assignable to phosphate ions and hydroxyl ions were reduced on calcinations. The specific surface areas of synthesized apatites decreased with increasing calcination temperature. Blood-clotting properties were evaluated in terms of active partial thromboplastin time, prothrombin time, and the amount of fibrinogen for the plasma in contact with the apatites, indicating that all the apatites barely influenced the blood clotting system. The apatites were in contact with a solution containing both bovine serum albumin (BSA) and beta(2)-microglobulin (beta(2)-MG), and the amounts of those proteins adsorbed on them were examined: the amount of absorbed BSA and beta(2)-MG gradually increased with the calcination temperature below 500 degrees C, while it showed a sudden increase when more than 600 degrees C. Hydroxy-carbonate apatite synthesized under a 15% CO(2)-containing N(2) atmosphere and calcined below 400 degrees C had the greatest selectivity in adsorbing beta(2)-MG. Thus, a higher selectivity for beta(2)-MG adsorption was empirically correlated to carbonate ions incorporated in the hydroxyapatite lattice.

Platelet adhesion on titanium oxide gels: effect of surface oxidation.

The correlations between titanium oxide layers on oxidized titanium (Ti) substrates and platelet adhesion were examined. Ti substrates were prepared by three different oxidation methods: the first one was treated with hydrogen peroxide (H2O2) solution, the second one was heated in air at moderate temperatures, and the third one was processed with both H2O2 and heating. The titanium oxide layers formed on the Ti substrates were characterized by wettability, chemical composition, thickness, and crystal phase. The platelet adhesion on these oxide layers was examined and correlated to the characterizations of the surface layers. The number of adhesive platelets seemingly correlated with the contact angle towards distilled water, because the number increased close to 70-80 degrees of the contact angle. The effect of surface oxidation on platelet adhesion was examined in detail and it was found that the composition and thickness of the oxide layer influenced platelet adhesion rather than wettability. Thick titanium oxide layers formed on Ti substrates by heating displayed less platelet adhesion than thin oxide layers on untreated Ti substrates. The largest number of adhesive platelets was found on H2O2-oxidized substrates; the substrates found on amorphous titanium oxide contained the Ti-peroxide radical species. The number of platelets, on the other hand, could hardly be observed on Ti substrates treated with H2O2 and subsequently heated above 300 degrees C. The titanium oxide layer on the substrate was thick and we found it to consist of only a few radical species. That is, the effect of heat treatment accelerates the growth of the oxide layer, and decomposes or decreases the number of radical species. Ti substrates with H2O2 and heat treatment above 300 degrees C held the least number of platelets, and were concluded to be the most inhibitory for platelet adhesion.